brocade

I have a Brocade ICX 6450 with router firmware. There are two VLANs 9 and 100. Both have a tagged port 1/1/1 that goes to an OpenWRT router. The OpenWRT router serves as DHCP server and firewall to WAN. I have been struggling for weeks now to configure this correctly. What I want...

Bought this layer 3 switch on Ebay. SFP ports are not working. I presumed it was a configuration issue. I have worked on it for days to find a way to enter the configuration mode, and never succeeded. Tried hard reset dozen of times, but it does not react as stated in the manual: amber lights...

Hi all! I'm interested in getting the Brocade ICX6450-24p as part of a pfsense build for my home network and have a few questions: I've seen a user on here who is giving away keys for this switch, is that all legal? Is this a good switch for running pfsense if I want VLANs? What kind of Noctua...

Hello, i want to sell a few things. So here is a list: Brocade ICX6610-24p - one PSU - need to sell it cause of the to high power drain - 330€ Intel Optane 900p 280GB PCIe HHHL - 14TBW - 220€ Samsung PM1725a 3.2TB PCIe3x8 HHHL- High Endurance drive 29.2PBW ( 0,044PB used) - 6200MB/s read...

Looking for some expertise here. Acquired this turboiron 24x on Ebay for a grand total of $80 delivered (canadian). Missing the OS. Installed the latest firmware (boot + primary) via TFTP. When booting though, I get a screen full of the errors during the boot cycle, and once booted.. if I...

I'm selling my Brocade ICX 6450-24P for 175 EUR plus shipping in the EU. This is the 24-ports 1GbE copper PoE version with 4x 10GbE SFP+. It's a full layer 3 switch with IPV4 + IPV6 routing, L2/L3/L4 ACL's, VRRP, OSPF, SNMP and sflow. The switch is fully upgraded to its latest firmware. The...

Brocade ICX 6610-48P I bought this switch on ebay for for $150 back at the end of January. It's too loud for me in my workshop. I've updated it to the latest firmware and did the whole license upgrade which I will blank out before shipping, but instructions on how to get unlimited ports on...

Hello everyone, I cannot get my switch to boot. I've tried re-flashing the uboot and the software via TFTP, which flash successfully. But but I run into errors each time I try to boot. I believe it might be completely bricked. Please assist if possible. Log output: Bootloader Version...

Hi there, i have recently aquired a couple of these badboys. The router itself is included with two PSU's, and missing the management module. they are from a former datacenter, that has turned the key. Shipping is possible in europe and costs around 230 USD. Local pickup in Denmark is also...

:( they work great but my pregnant wife cant yell at me from upstairs for me to hear her in my office. they are fully updated but will not have any licenses on them (you can reach out to fohdeesha for that :) will sell with 2 fans and 2 power supplies (switch is POE but power supplies are not...

Hi All, I am looking to get 2 high density 10GB switches to replace my brocade VDX 6720 the vdx 6720 is fine but the 2 I have have 2 limitations that make them not that usefull 1- I have only 16 ports licensed 2- to connect both switches I dont have qsfp port so I am using 4 out of the 16...

Hello, Looking for a reasonably priced Aruba S2500-45P or Brocade ICX 6450-48P. Located in California, in the Bay Area.

Hello everyone, I'm looking for (a) reasonably priced Brocade ICX 6450 (2 x 24 port w/ at least 1 having PoE, or 1 x 48 port w/ PoE) switch(es) to start my home lab. I just bought an old Dell PowerEdge R210 ii to build a router and I now need a switch. I'm located in the northern California...

Have any of you had any experience with Ubiquiti (Ubnt) gear and the ICX? I am trying to keep the 10gb traffic constrained within the 10gb ports, and only route out when needed to reach a client on the wifi or the internet since the PR01 is connected via 1gb links. I can setup static routes...

Hello STH, I was hoping someone here might be able to help me convert an existing config snippet from a Dell 62xx/70xx to the Brocade FastIron equivalent on an ICX6610 (8.0.30sa)... Background: In order to use your own router with the Google Fiber 1gb/1gb service (at least their...

Hi there all, I've just finished setting up a nice AIO proxmox server and between it and my workstation (direct connection), it saturates 10Gb or gives a faster then local SSD speed depending on work load (NFS maxes out at 4GB/s but thats a different thread)......and now I want more. Well not...

Hi everyone. This is my first post here. Hopefully this is the right place for my thread. If not please point me in the right direction. :) Anyway, I bought a Brocade ICX 6430-C12 on ebay last week. I just got it today, hooked up my console cable, powered up the switch, and it is not booting...

UPDATE 7/11/2018 - It's been discovered that the version 8 Brocade firmware originally on the site was an internal-use only, untested beta version. It has been removed from the guide and replaced with the latest v7 mainstream release which is rock stable, well tested and has had a few more...