supermicro

Finally getting around to selling this. I'm sure everyone is pretty familiar with this system. It was my main home server for near three years and would be an excellent NAS or home router: Supermicro | Products | SuperServers | 1U | 5018A-TN4 Importantly, I had it sent to Supermicro already...

Hello all, I'm new to server building and have an issue. I bought a Gigabyte GA-7TESM dual 1366 motherboard and a Supermicro CSE-835TQ 3U case, both refurbished. The chassis has dual redundant 1200w p/s. I've installed everything correctly, except the OH LED and Intrusion Detection. I cannot...

Hi everyone, I have a Supermicro X11SSM-F that is currently housed in a tower enclosure. In order to provider neater organization and to allow for drive expansion (even with my 4-in-3 Icy Docks, I'm limited to ~ 12 drives in my tower chassis), I'd like to move this into a proper chassis. After...

Hi All I have a client who is buying a 1U single socket Supermicro server with an Epyc 7351P 16 Core processor. The application is as a small Proxmox host, running Debian VM instances for clients. The intention is to run about 40 VM's at 128GB of RAM (32GB modules), but retaining the option...

Googled, but no luck... Seems like Supermicro H11DSi-series is the only motherboard for Dual EPYC configuration... The other choice is Gigabyte MZ31-AR0 or Tyan Tomcat SX S8026, but it has only a single EPYC socket... I like my Supermicro H11DSi-NT, but it has no Hard Disk Drive activity LED...

Hello, I have a X11SAT-F motherboard with IPMI support running linux under EFI mode. I want to use SOL for the remote server. I appended the kernel command line to the following, linux /@/vmlinuz-4.9.95-gentoo root=ZFS=rpool/ROOT/gentoo ro spl.spl_hostid=0xa8c06f01 console=tty0...

I built this at the end of last year but have since decided to use 3x Cisco UCS servers for my hosts. Specs: 1x CSE-216 SAS2 24-bay 2U chassis with SAS2-216EL1 backplane 1x Supermicro X10DRI-B Dual LGA2011 EATX Mobo 1x Supermicro Active CPU Heatsink SNK-P0048AP4 1x Intel E5-2630v3 2.4GHz...

I am trying to decide between purchasing an sc836 barebones chassis, one with the Bpn-sas-836tq backplane and the other with a Bpn-SAS2-836el1 backplane for about the same price. I will be connecting either backplane to a SAS2 HBA and still haven’t decided on SAS or SATA drives so I would like...

Hi, I just got a Supermicro X9SRi-F, and am using a Xeon E5-2670 with it. My problem is that when I turn it on, the fans spin, and I can access IPMI, but there is no VGA output and as far as I can tell it doesn't boot (IPMI can't read temp or other stats). No beep codes happen. Any ideas?

Have a chassis with the narrower set of inner rails, tool-less, snap-in, made by Repon but no part number, looks to be similar to a Rev B set of inner rails. They came included with a 847E1-R1400UB chassis. The inner rails are looking for their forever match- a pair of left and right outer...

I got tired of the noise with my SuperMicro X10 Server (4027GR-TRT), but didn't want to get into involved hardware fan swaps which still may produce unsatisfactory results. For reference, the "Optimal" fan setting decided to run half of the fans at 8000RPM at idle, and the other half at 5000RPM...

Hi, I have a supermicro 2U case which I love, but it's in my office and it's a little loud for office work (can even be heard over my switch, which is also loud). My girlfriend has also been complaining about it recently. I replaced (most) the fans in the switch with noctunas, which I had to...

Supermicro CSE846 SAS 2 2 PWS-920P SQ PSU All sleds includes NO Rails included $564 Shipped

We have Hyper-V Server on which we created VMSwitch (with Switch Embedded Teaming) on two built in Intel x722 adapters. On VMSwitch we have NetAdapter for Management OS with ip assigned (created along with vmswitch). After creation everything works fine until reboot, after which we are...

Hi All, I've been doing a bit of reading on how to use impitool to adjust the fan thresholds on my motherboard, to prevent the spin up/down issue that some people have previously reported. The basic steps I took were as per Decrease Supermicro IPMI Fan Threshold This MB has 5 headers, FAN 1...

Supermicro X11 or H11 onboard LSI 3008 are shipped with IR mode firmware ph.10. After few email exchange with Supermicro Support, here is the summary, its their official advisory that user can invalid their warranty if they want to flash the onboard LSI 3008 controller firmware to IT Mode...

I'm building a 4 node vmware cluster using supermicro x9scm-f mainboards. I've setup 2 nodes so far without any issues. This third node seems to have a strange mainboard id on the vmware boot screen. Did anyone ever see this before ? What could this be ? I've double checked all bios settings...

Hello, I am trying to pull some parts together from Supermicro and was wondering if you could give me some guidance on compatibility. I purchased a used X9SCA-F motherboard and had the following questions: 1. It appears that if the board is running BIOS revision 2.0 or above that it...

Hey STH, Wondering if anyone has seen a server that has top load 2.5" drive bays. Similar to the SuperMicro or 45-Drives 60/90 bay top load servers but for 2.5" drives. Where that came up was we just brought in EMC's XIO platform at work and the drive enclosures are top load, approximately 2U...

Hi folks! At work we have an older Nexenta ZFS rig serving mostly iSCSI to ESXi blades that my boss is getting worried about because we have no "support" and the drives are getting old, and the people who built it made a zpool ashift choice error (default ashift=9 rather than forcing 12) so we...