dell

Are OCP 3.0 interchangeable? they are normally very pricey, but I have that 1U Lenovo that is lovely but lacks pcie slots, and has the OCP 3.0 slot available... These Dell are "reasonably" priced, but will they work? Not vendor locked?

Hi and thank you for the great community! I have a 4TB SATA HDD, Dell-branded, model ST4000NM0035, manufactured by Seagate. I would like to update its firmware, but am having a tough time. Below I will describe what I have tried so far. The HDD came in a Lenovo P330 SFF gen 2. In this...

Hello folks! I'm considering buying a Dell PowerEdge M1000e Blade Server Chassis which comes with a Mellanox M3601Q switch I/O module on the chassis. The thing is that this switch according to Dell documentation is a Infiniband switch. Is that possible to convert it to an ethernet switch? Like...

UPDATE: I opened a support ticket with Intel and they were able to confirm that the x710-DA2 does not support x2 speed. Only x1, x4, or x8. I have 10gb networking in my desktop and recently upgraded from an Intel x520-DA2 to an Intel x710-DA2 (Dell OEM original fully updated firmware). I did...

It is time. I have a pair of loaded dell servers that I am now ready to sell. They are similar in spec to the following: Dell PowerEdge XR12 Server - Xeon 8352M 32-Core 512GB RAM 6x 3.84TB SSD H355 | eBay They want $14K for one. I can sell 2 of a similar (actually better in some of the...

recently had a couple Dell-branded 5100 PRO M2 drives (installed in BOSS-S1 cards in some PowerEdge M640's) die. naturally, the Dell version (model MTFDDAV240TCB-1AR1ZABDA) of this drive seems to be long out of production, and is super expensive. i bought a few of the standard, non-customized...

I recently purchased a PCIe NVMe drive for my PowerEdge R740. It is the "Dell PM1725 NVMe SSD," manufactured by Samsung. The Samsung part number is MZPLK3T2HCJL. iDRAC9 showed an available firmware update: "Express Flash PCIe SSD." After successfully downloading the update, the installation...

Hello! I have just gotten my hands on a Dell H330, and I have two questions. Firstly, can I flash to IT mode with a different computer than the original one? I found a few guides on flashing it, but all of them seem to use the server it was in. Secondly, what cables can I use with it? In the...

I was about to get a 9361-16i from eBay for my new Minisforum MS-01 when I noticed that I can get a "Dell MegaRAID 9460-16i" (aka 42PDX) at a better price. And as a newer generation, I guess it should be a better card, right? But can it be flashed to a proper LSI 9460-16i? If so, how? And I do...

Words fail me in dealing with these damn things. Here follows a choice selection of merely the most perplexing and baffling of issues... 1) You may never again see your screen light up after a RAM or CPU upgrade. 2) RAM errors can be CPU-dependent; simply leaving you screenless on one chip...

For sale are 3x PowerEdge R730 2U servers Each server has 2 Xeon E5-2690v4 CPUs Those are 14 core, 28 thread clocked at 2.6GHz 24 sticks of 32GB DDR4 ECC for 768GB of RAM in each server. 2400MHz RDIMMs (Samsung) They have 8x 2.5" drive sleds Doesn't come with drive sleds (only blanks) but...

SOLD Selling a Dell PowerEdge T640 18LFF 3.5" server. This is a homelab dream server with 18 LFF 3.5" bays for massive storage potential. Has 9 PCIe slots (less one for the HBA) for all your GPU, NVME cards, etc. These towers run nice and quiet also. This comes fully populated with trays as...

I've been dealing with this for the last few days: I've been trying to setup a TP-Link AP with two SSIDs on two different VLANs, to connect to my OPNSense box via a Dell X1026 switch. Seems straight forward, right? Yeah, but I guess I'm missing something because I can't even get a DHCP lease...

We have a range of Dell servers (R710, R720, R520, R320, R820s) - I noted in IDRAC that some of the PSU's shows present | failure, however, the PSU seems to work without an issue. We unplugged the other cable and the "failed" PSU still works. Rebooting the server does not take the error away...

I bought an Epyc 7713 off of eBay, the processor, it was listed as a Dell part (didn't see until after bought). The CPU has been used before (small scratches). Installed it into a new ROMED8-2T and I was able to install Ubuntu onto it. Does this mean the CPU isn't locked, or are there other...

Hello, So I recently got my hands on two Dell z9100-ON switches. I plan to run these in VXD failover mode, but I'm struggling to even get a single interface up. I should mention, I am completely new to SONiC OS (and all NOS's for that matter). I have flashed both switches to Sonic-OS NOS ...

Hello, I have a set of used R7525's, and I've filled all the hdd's as I need, but I dont have any hdd blanks for the front. I cant seem to find a product code for it (I can only find them for the Rx30 series servers. Can anybody help?

DELL EMC 9hxk6 12tb 7.2k rpm nlsas 12gbps 512e Hey there! So, I've got this DELL EMC 9hxk6 hard drive that's been chilling in my place. I got it a while back for a project that never really took off. It's 12TB, spinning at a decent 7.2K RPM Selling for $205 This runs on NLSAS at a speedy...

I recently got a Dell EMC VEP 4600 and noticed the fans run a little too fast. Is anyone experiencing something similar. I saw couple units that were "normal with fans around 6k, but mine seems stuck with fans fans at 12k-14k rpms when the cpu tems is ~33C. It seems a little too excessive to me...

I've scored two Dell PowerEdge T420 servers at a steal on Facebook Marketplace. I'm gearing up to install Unraid on one of them, and could use any insights available. Will Unraid play nice with iDRAC? Also, I've seen theres talk about flashing the RAID controller - any firsthand experiences or...