H12SSL-I Stuck at "bmc initiating"

Notice: Page may contain affiliate links for which we may earn a small commission through services like Amazon Affiliates or Skimlinks.

Dick Lee

Member
Nov 6, 2022
30
0
6
Hi All!

A green hand here. I bought an OEM H12SSL-I to set up my first server. It was working fine until some meddling with the bios. Result? It cannot boot up and stays at "bmc initiating" forever! Now, I can't enter bios or ipmi console no matter how I tried. Any advise to make it work again?
 

i386

Well-Known Member
Mar 18, 2016
4,382
1,619
113
35
Germany
OEM Board?
What does medling with the BIOS mean? Playing with settings or modifying IT with external Tool?
 

i386

Well-Known Member
Mar 18, 2016
4,382
1,619
113
35
Germany
Could it be caused by changing several PCIE devices without switching off the machine?
You mean like plug and play? :D
I wouldn't do that. Even when pcie as a standard supports some sort of it most devices, their drivers, os and the mainboards can't handle it...
 
  • Like
Reactions: Sogndal94

NablaSquaredG

Bringing 100G switches to homelabs
Aug 17, 2020
1,564
1,010
113
Not stupid as that, just switching pcie cards after shutting down OS but not PSU.
Usually not, I do it all the time. But maybe if you haven't taken ESD precautions...

Have you tried booting the board on a table to make sure there are not standoffs at wrong positions causing short circuits?
 

RageBone

Active Member
Jul 11, 2017
638
165
43
indeed, try a cmos reset.
Also, it is very very weird that you can't access the ipmi, has that always been the case?
 

Dick Lee

Member
Nov 6, 2022
30
0
6
indeed, try a cmos reset.
Also, it is very very weird that you can't access the ipmi, has that always been the case?
I had done exactly as RolloZ170 suggested but to no avail. Some googling let me know that BMC initiates before bios. Really, the issue is BMC not bios.
 

RolloZ170

Well-Known Member
Apr 24, 2016
6,321
1,930
113
Some googling let me know that BMC initiates before bios. Really, the issue is BMC not bios.
you switch the PSU on and wait for the BMC heartbeat LED to flash, then press the power button.
if you start the system to early the BIOS waits for the BMC to initialize...
The BIOS want to give the BMC some data, if not responding nothing happens then.
Do you had access to the IPMI WebGui before your manipulations ?
 

Dick Lee

Member
Nov 6, 2022
30
0
6
No IPMI ip settings are done and I had never accessed the webgui. One strange thing: once I plugged in the power cord and turned on the psu, the cpu fan spun at highspeed immediately. When the server functioned properly, I needed to push the power button to turn on the machine. Any implications?
 

RageBone

Active Member
Jul 11, 2017
638
165
43
No IPMI ip settings are done and I had never accessed the webgui. One strange thing: once I plugged in the power cord and turned on the psu, the cpu fan spun at highspeed immediately. When the server functioned properly, I needed to push the power button to turn on the machine. Any implications?
do you even have a BMC Heartbeat?
If not, well, something is seriously wrong.
Hopefully just FW
 

Dick Lee

Member
Nov 6, 2022
30
0
6
do you even have a BMC Heartbeat?
If not, well, something is seriously wrong.
Hopefully just FW
It beated crazily and that was why I knew it was stuck at "bmc initiating". I know a BMC reflesh should solve the problem but the problem is that I have no access to the console. Any ideas?
 

RolloZ170

Well-Known Member
Apr 24, 2016
6,321
1,930
113
I know a BMC reflesh should solve the problem but the problem is that I have no access to the console. Any ideas?
USB programmer like ch341a. or buy a preprogrammed chip, and replace the BMC chip.
you need no special equipm.cut one pin row with a side-cutter and bent the chip as long it drops off, clean the pads with solder iron, resolder the new chip.
 

Dick Lee

Member
Nov 6, 2022
30
0
6
USB programmer like ch341a. or buy a preprogrammed chip, and replace the BMC chip.
you need no special equipm.cut one pin row with a side-cutter and bent the chip as long it drops off, clean the pads with solder iron, resolder the new chip.
I'll take this as the last resort. Is there any other way to reset, reflash BMC? I guess toys like Supermicro IPMI SIMLP-3+ are not usefull in this scenario?