Supermicro H12SSL-CT Boot (0x62) and BIOS update Problem.

[shub]

Hehey Folks

Ok i come directly to my situation.

What's the HW:
Mainboard: Supermicro H12SSL-CT ( REV: 1.01 )
CPU: AMD EPYC 7232P
RAM: 2x Samsung 8G 2Rx8 PC4-2133P-RE0-10-MB1 ( M393A1G43DB0-CPB2Q S )

If i put all power cables on ( both cpu and the big 24 pin) the POST stops at:
DXE--USB Initialization and right on the IPMI/BMC screen/console is the code 62.
The 0x62 is "Installation of the South Bridge Runtime Services", this is the end of the "POST"-road.

I've tried to put the RAM sticks solo or in any different kind on the board, i've tried to CMOS reset and factory reset and nothing brings me a step further.

So i downloaded the BMC and BIOS software and first i updated the BMC from 01.00.34 to 01.00.35 and it work, the new versions was there.
Then i updated the BIOS from 2.01 to 2.03, after the update process, the device does a reboot and ... ?!? it is still BIOS 2.01..

So, after reboot 3 times, i have to ask for help, the POST process stops still at (DXE--USB Initialization / 62) and i can't update the BIOS, the proces of the updates goes really smooth, but after it is still 2.01.

This is the data under BMC -> Firmware -> Inventory:
BIOS BIOS Date: 06/02/2021 Ver 2.1
BIOS Backup Not Present
BIOS Golden BIOS Date: 06/02/2021 Ver 2.1
BIOS Staging BIOS Date: 10/20/2021 Ver 2.3
BMC 01.00.35
BMC Backup Not Present
BMC Golden 01.00.34
BMC Staging 01.00.35
CPLD Motherboard F0.A6.44

I hope someone can tell me, what i'm doing wrong.

Best regards from Switzerland (sorry about my horrible english)

Andi

 

[RolloZ170]

I hope someone can tell me, what i'm doing wrong.

first the BIOS rev. you see in the IPMI is updated by the BIOS after successfull POST.
your POST is incomplete, so you see the last successfully data only.

 

[RolloZ170]

CPU: AMD EPYC 7232P

new unused CPU ? or out from DELL ?

 

[shub]

first the BIOS rev. you see in the IPMI is updated by the BIOS after successfull POST.
your POST is incomplete, so you see the last successfully data only.

Ok and that means ? Is there a way for troubleshoot or .. dead ? Its a new CPU.

 

[RolloZ170]

Ok and that means ? Is there a way for troubleshoot or .. dead ? Its a new CPU.

that means you see the rev. of the new BIOS if you got a successfull POST (hopefully) soon.

 

[RolloZ170]

reseat CPU.
some rumors say EPYC rome does not like 2133 RAM, is a chance to check with other ?

 

[shub]

yes but i've only non-ecc 8G-3200.

 

[RolloZ170]

Ok and that means ? Is there a way for troubleshoot or .. dead ? Its a new CPU.

Dein BIOS muss erstmal erfolgreich POSTen damit es dem BMC/IPMI die neue Version melden kann.

 

[RolloZ170]

yes but i've only non-ecc 8G-3200.

buy something cheap at ebay. not 2Rx8 8GB. may to oldish for the EPYC mem.controller

 

[shub]

Dein BIOS muss erstmal erfolgreich POSTen damit es dem BMC/IPMI die neue Version melden kann.

Ja das hab ich jetzt geschnallt, danke dir. Mit den 8G 3200 DDR4 Kann ich nix machen da, verträgt nur ECC RAM oder ?
Ja nächste Woche kommen 2x 16G 3200 ECC RAM. Leider musste ich sehr lange auf die warten.

 

[RolloZ170]

Ja das hab ich jetzt geschnallt, danke dir. Mit den 8G 3200 DDR4 Kann ich nix machen da, verträgt nur ECC RAM oder ?

genaugenommen nur RDIMM, ECC ist gut wenn es dabei ist.
RDIMM exactly. ECC is good to have.

 

[shub]

genaugenommen nur RDIMM, ECC ist gut wenn es dabei ist.
RDIMM exactly. ECC is good to have.

Hey vielen vielen dank für die Info, das hilft mir wirklich sehr weiter. Lese auch gerade weiter das es tatsächlich "rome" mit 2133 nicht so gut hat, sogar 2466 geht nur mit glück.

 

[RolloZ170]

but you can test with the 3200 RAM, if the error stays the same it snot the memory thought

 

[shub]

I did it already few mins ago, won't boot at all. Nothing, blank screen.

 

[jnolla]

Were you able to solve this problem?

 

[geonap]

i'm having this problem on an H13SSL-N with an epyc 9554, it's weird, i had booted this box before, i moved it to it's chassis after 2 months of it being in a static bag and it was stuck at the initial screen, i was able to update bmc.bios from bmc , it looked like it was going to boot up but sits at usb initializing, 62