Minisforum MS-01 PCIe Card and RAM Compatibility Thread

Notice: Page may contain affiliate links for which we may earn a small commission through services like Amazon Affiliates or Skimlinks.
Where can I find the oculink 8i PCIe card and egpu enclosure?

That's unfortunately a question I don't know how the answer to.

I bought it off of Superbuy and it took a couple of months to get to me.

In that time the listing disappeared and I've not seen another one.

It's an OSMETA EG-01 GEN 4 and they made a gen 5.

But the taobao and superbuy links seem to have fallen off the face of the earth.

Not sure what that means as I don't reas Chinese.
 
Can anyone tell me what comes in the box with the machine? I have bought two NVMe drives for my barebones model but only one of them came with a screw, do I need to get my hands on a screw for the other one and a set of standoffs for both?
 
Can anyone tell me what comes in the box with the machine? I have bought two NVMe drives for my barebones model but only one of them came with a screw, do I need to get my hands on a screw for the other one and a set of standoffs for both?

No, you're good, there are standoffs and screws for all three M2 slots.
 
  • Like
Reactions: nickramsbottom
QNAP 4-port SFF-8088 adapter from the QNAP TL-D400S JBOD kit.

I'm having problems with this one, driving me a bit nuts. The SFF-8088 card included with the TL-D400s – a qxp-400es-a1164 – is not recognized in the MS-01. The card is good, shows up fine in my desktop (tried in windows, ubuntu and unraid) but the minisforum does not see it.

I tried a network card to check if the PCIe slot was perhaps bad in the MS-01: it's not, the NIC shows up fine.

Before I send back the QNAP, is there anything obvious I'm missing? Any advice appreciated!
 
Help needed!
I have a WD Black 850 playstation version, it barely fit on the leftmost slot PCIe 4.0 x4 so I am thinking about putting on the SSD with an adapter on the PCIe 4.0 x16 slot so that i would take advantage of full 7000mb/s speed
The leftmost slot would be used for my Samsung 990Pro which fits with the heatsink that Minis Provides with the MS-01 and use the other two slot for older/slower NVME (proxmox OS)

Any issue I may encounter? I am new to proxmox so I am afraid of compatibilities issue

thank you !
 
I'm planning to get a Samsung 990 pro 4TB for my ms-01 and I'm struggling to decide if I should buy the one with a heat sink or not. The one with a heat sink is a bit cheaper and could help with the heat, but will it fit? Does anyone know? :)

For those in the future I got a Samsung 980 Pro with Heatsink, and it does not fit, not because its too tall, but because its slightly too wide!

I got the barebones MS-01, and it does indeed come with its own heatsink. Ill probably end up removing the heatsink and using the provided one. Got a RX 6400 card as well and that fits just fine, after swapping out the bracket for a low profile bracket.
 
  • Like
Reactions: Relock25
For those in the future I got a Samsung 980 Pro with Heatsink, and it does not fit, not because its too tall, but because its slightly too wide!

I got the barebones MS-01, and it does indeed come with its own heatsink. Ill probably end up removing the heatsink and using the provided one. Got a RX 6400 card as well and that fits just fine, after swapping out the bracket for a low profile bracket.

If anyone gets the Samsung ssd with heatsink as well by mistake and it doesnt fit too, here is a guide with images I found for removing the heatsink: . Haven't tried it yet as I don't have the screw bit needed.
 
Support got back to me and asked me to try T500 in slot 1 with GPU but disable vt-d and sure enough that worked. It sure looks like a bios issue now. Sure hope they fix this soon, I definitely don't want to leave that disabled for future VM plans.
Well we have a bios update. I will report back when I try it.
 
I have moved my MS-01 fully into "production" in my homelab. It's now running everything that was previously running on my Lenovo Tiny with a 10GbE NIC installed. The power consumption continues to impress--steady state with everything running is still right around 20W, 5W lower than the Tiny, with a more powerful CPU.

My only issue thus far is thermals, which is not unexpected. NVME temps are pretty solid, even with all 3 NVME slots populated. CPU temps at base loads are fine, but not great--10-12C above ambient. But as soon as anything CPU-heavy starts running, it gets to 90C and starts to throttle pretty quickly. I may ultimately try replacing the stock thermal interface material. I don't have any liquid metal around and haven't used it in the past. Am I likely to see any benefit from simply repasting with halfway decent thermal paste like Arctic MX-4?

Thanks.
 
  • Like
Reactions: minisfckr-01
Okay so after diving through this forum I have been left a little confused on the topic of if the 12th gen CPU actaully can account for 96GB RAM. I mean opinions are at times conflicting and I simply wish there was evidence. Well someone shared that with me and they are okay with me showing it with you guys so see the image attached. This is with a system that has a Intel Arc A310 GPU in it by the way.Screenshot 2024-05-01 025451.png
 
I have moved my MS-01 fully into "production" in my homelab. It's now running everything that was previously running on my Lenovo Tiny with a 10GbE NIC installed. The power consumption continues to impress--steady state with everything running is still right around 20W, 5W lower than the Tiny, with a more powerful CPU.

My only issue thus far is thermals, which is not unexpected. NVME temps are pretty solid, even with all 3 NVME slots populated. CPU temps at base loads are fine, but not great--10-12C above ambient. But as soon as anything CPU-heavy starts running, it gets to 90C and starts to throttle pretty quickly. I may ultimately try replacing the stock thermal interface material. I don't have any liquid metal around and haven't used it in the past. Am I likely to see any benefit from simply repasting with halfway decent thermal paste like Arctic MX-4?

Thanks.

I was seeing temps in the 80s when I first got my MS-01.

I cleaned up the paste and put some of that PTM7950 Honeywell phase changing stuff on.

Last night I monitored it for 10 hours and the highest temp I saw recorded was 75 degrees.

Probably not running the same load you are, I was just watching TV on Plex and playing FFXIV.

Redoing the paste is def worth it
 
My only issue thus far is thermals, which is not unexpected. NVME temps are pretty solid, even with all 3 NVME slots populated. CPU temps at base loads are fine, but not great--10-12C above ambient. But as soon as anything CPU-heavy starts running, it gets to 90C and starts to throttle pretty quickly. I may ultimately try replacing the stock thermal interface material. I don't have any liquid metal around and haven't used it in the past. Am I likely to see any benefit from simply repasting with halfway decent thermal paste like Arctic MX-4?

Thanks.

FWIW I applied liquid metal for the first time on my MS-01 CPU and it was not difficult, just take your time. CPU temps went down significantly (~10C).