thats the QWAT
i have it on X11SPM BIOS 1.6 - was latest that time
X12SPL-F Failing to boot after Bios
- Thread starter John Burns
- Start date
Notice: Page may contain affiliate links for which we may earn a small commission through services like Amazon Affiliates or Skimlinks.
i have it on X11SPM BIOS 1.6 - was latest that time
or just send offer to this seller, QWAP is little better
Intel Xeon Platinum 8368Q ES QWAP 2.3GHz 38C/76T 57MB 270W LGA4189 CPU for C621A | eBay
Find many great new & used options and get the best deals for Intel Xeon Platinum 8368Q ES QWAP 2.3GHz 38C/76T 57MB 270W LGA4189 CPU for C621A at the best online prices at eBay! Free shipping for many products!
www.ebay.com
no that is the Firmware for the CPLD( "Complex Programmable Logic Device" ) chip on the motherboard
the "Lattice" above the battery.
Guys, help me with a question
updated the system
BMC Firmware Version 01.03.11
BIOS Firmware Version 1.9
but the Internet does not work, it says unidentified network
reinstalled Windows did not help, question, how to solve the problem
NOTE: I move the same disk to the X10 system, the Internet works
updated the system
BMC Firmware Version 01.03.11
BIOS Firmware Version 1.9
but the Internet does not work, it says unidentified network
reinstalled Windows did not help, question, how to solve the problem
NOTE: I move the same disk to the X10 system, the Internet works
connected to BMC LAN ? this is at stock config not accessible with OS, only for remote.
use other 2 1GbE LAN ports.
if you still use these two your router may not support 1GbE.
Thanks for the answer
I did the following, updated Bmc and then Bios and Ethernet was restored
Now I'm faced with a new problem: for some reason the processor is running at full power in stock and the memory frequencies are not displayed
BIOS Date: 01/03/2024 Ver 1.9
BMC 01.03.11
Another question.
What should be the system update sequence?
Bios-first and after BMC or BMC-first and Bios
What should be the system update sequence?
Bios-first and after BMC or BMC-first and Bios
only if problems(never change a running system)
BMC then BIOS (with BMCWebGUI or SUM)
note on X12/h12 systems only the BMC can flash Firmware,
wait longer to complete windows background processes.
and in windows high perf.profile it looks like that for minutes after boot.
its not a desktop board, on server boards the BMC gets full access of RAMs SPD i.e.
install correct drivers and use actual HWinfo version.
I already realized this a few hours ago when I tried to reflash it through Afudos and sewed the Shell
you mostly brick the board with AFUxxx. read the notes, ther is a warning/note from supermicro.I already realized this a few hours ago when I tried to reflash it through Afudos and sewed the Shell
Yes, my router supports to 2.5GbE i have optical i-net connection
and cables are connected correctly
I tried to update BMC and BIOS as in the picture, v 1.6 but the problem was not solved
remove the cable from BMC LAN(should not avail. in public)
and use this for the other LAN ports. btw. they look not plugged correctly...
device-manager ? intel NIC drivers correct installed ?
edit:
LAN Port Enable/Disable Jumper ???
Last edited:
still no device manager access ?
if there is a problem it will be reported. if no problem, cable or NIC defective = RMA board.
Today at some stage of the installation there was internet for a while, but when I rollback to 1.6 the internet stopped working, I tried updating to the latest version with no results
Last edited: