You are correct, I had screwed up the port VLAN membership - open to ideas on how to lock it down!This is wrong. I am accessing the WEB interface from a different VLAN.
You are correct, I had screwed up the port VLAN membership - open to ideas on how to lock it down!This is wrong. I am accessing the WEB interface from a different VLAN.
It's a limitation of the switch chip/platform used. That's why it's available in either 4 + 2 or 8 + 1 variants. There are new switches using MaxLinear switch chips hitting the market that support 8 + 2 though, although unmanaged versions so far.Got the switch to enhance my 2.5 GbE capabilities in December. Bit weird to only have one SFP+ for eight 2.5 GbE ports. Would love to see a new version with two SFP+ ports to fully enable all ports utilizing the full bandwidth at the same time.
Amazing! Thanks for letting me know and pointing me the right direction
Try creating the user root (password doesn't matter), save config changes. SSH in. Profit! (Hopefully).Anyone tried to SSH into MokerLink 2G05210GSM switch? I have tried to SSH in, but it gives me 'Incorrect User Name!!' error even though it's the same admin account I login to GUI.
View attachment 34746
Are you just guessing or have you seen that same error before?Try creating the user root (password doesn't matter), save config changes. SSH in. Profit! (Hopefully).
Hello friends,Just want to say thank you to folks in here. I bricked my XikeStor 8 +1 managed by installing the wrong firmware (used the SWTG118AS as this is what the PCB was marked as).
The router did not automatically switch over to recovery mode, but once I hooked up a FTDI USB to serial and powered on while holding the Esc key with Putty open and set to use the ttyUSB0 connection and at 57600 it came to life and I was able to load the correct firmware.
For anyone else flashing a managed switch, make sure you use SWTGW218AS even though the PCB is marked 118AS.
Also, I came across another "brand" of this same switch called "YuLinca" on amazon.ca. I just received so I haven't cracked it open yet, but from the outside other than the faceplate and the fact that this one bears the UKCA mark in addition to the CE mark, it is identical.
The power supply is not the same. The YuLinca looks and feels a lot cheaper than what came with the XikeStor. $109 CAD with $10 off coupon.
Usually a fast blinking LED indicates it's in download mode at http://192.168.1.1 (not https, some browsers will force https so disable that feature)I have a few questions.
1. Which pins to connect on the motherboard (pictures above) with the FTDI FT232BL USB device (if possible please send me a sample photo).
2. what software will I need to upload the new software?
3.Brief instructions so that I can upload the new original soft.
4. Can I program the flash itself using CH341 programmer?
Please step by step to revive my device. Thank You my friend's!!!
Is this how it should be ?Usually a fast blinking LED indicates it's in download mode at http://192.168.1.1 (not https, some browsers will force https so disable that feature)
1. SWTG118AS/photos/SWTG118AS-v1.0/SWTG118AS-v1-pcb-front.jpg at main · up-n-atom/SWTG118AS And make sure the jumper is set for 3.3V and you might need to swap RX and TX wires but typically it would be RX to TX and TX to RX (DO NOT CONNECT VCC)
2. Terminal Emulator like Putty or RealTerm or TeraTerm assuming you're on Windows and a Web Browser
For which hardware / firmware does this work?Try creating the user root (password doesn't matter), save config changes. SSH in. Profit! (Hopefully).
It's for a completely different switch platform (RTL8373 + RTL8224), which is why I directed the user (I think it was the same user) to the Hasivo thread for the particular unit that Mokerlink rebranded.For which hardware / firmware does this work?
It does not work for SWTGW215AS / SWTGW218AS with FW 1.9. Switch does not respond to ssh at all.