Notice: Page may contain affiliate links for which we may earn a small commission through services like Amazon Affiliates or Skimlinks.
Thank you for your reply
I currently have the 7402P on and it is working fine with bios 3.2.
Is there a big possibility that this milan ES is broken?
doesn't necessarily have to be.
have not seen asrock was reported running genesis A0.
I see...you mean it may not work with ROMED8.
I also have H12SSL I, but I have not tried this one yet.
Thanks for the information!
I've been looking into the H12SSL bios for a while now, but I couldn't find any information about it working with 2.0, so this is very helpful!
I've been on 2.4 since I bought it and supermicro says that if you update to 2.1 or higher, you can't roll back to before 2.1. Besides, it appears that they don't release bios prior to 2.5.
I will ask supermicro and the place I purchased it from if there is any way to roll back to 2.0.
I've been looking into the H12SSL bios for a while now, but I couldn't find any information about it working with 2.0, so this is very helpful!
I've been on 2.4 since I bought it and supermicro says that if you update to 2.1 or higher, you can't roll back to before 2.1. Besides, it appears that they don't release bios prior to 2.5.
I will ask supermicro and the place I purchased it from if there is any way to roll back to 2.0.
Thanks to your help, I was able to obtain 2.1 and 2.0.
First I tried updating 2.0 with BMC, but it warned me that it could not be rolled back, so I put in 2.1. 2.1 could not POST milanES, so I tried 2.0 with UEFISHELL, but at the last minute I got an image warning and could not downgrade. I could not downgrade.
I will ask Supermicro if there is any way to downgrade to 2.0.
Your kind advice has helped me a lot in troubleshooting. Thank you very much!
EFI tool can not access the BIOS on this platforms, it just uploads the BIOS file to the BMC and let em do the job.
only by replace of the BIOS chip with preprogrammed with 2.0
In the end, we did not send the H12SSL to Asrock, but bought a used mz32-ar0 rev1 and are trying to see if Milan ES will work. After gathering information, it seems that the bios containing milanpi 1.0.0.1 that you mentioned is in MZ62, but I could not find it in mz32-ar0.
Asrock, like Super Micro, has not released any bios other than the two most recent ones, so I'm stuck in a situation.
If you know of any bios that will work with Milan ES, please let me know
Thank you in advance.
Asrock, like Super Micro, has not released any bios other than the two most recent ones, so I'm stuck in a situation.
If you know of any bios that will work with Milan ES, please let me know
Thank you in advance.
if you run Rome you see RomePi not MilanPi
you need to run Rome/Milan BIOS, you have probably Naples/Rome BIOS now.
here is a BIOS for MZ32-AR0 MIlanPi 1.0.0.4 and Milan step. A0 microcode.
MZ32-AR0 rev.1.0 and 3.0 are same except Firmware.
server_bios_mz32-ar0_M07_R26.7z
note: use this link above, not the links from replies, they are not updated if i change it here.
Last edited:
Thank you for your response! The file did not seem to be in the link. If you don't mind, could you upload it again?
The BMC did not pass the PASS that was attached to it, and when I checked with the seller, they told me to reset it. I will talk to GIGABYTE about resetting it first.
