routing

  1. D

    40G/10G network issues/config

    I have a 40gb network that handles the storage for my ESXI enviroments, 3 hosts and a SAN. For a while this networrk was only ever accessible to the machines connected directly to the SX6036. I wanted some of my other machiens to be able to access this on their 10g conenctions that are connected...
  2. BackupProphet

    ipv6 Linux router

    So I just got a 2001:1234:2000:200::/56 network from my ISP and is trying to get it to work. Most thing seems to work as they should. But for some reason it feels like my *internal server* is behind a NAT. There is internet access, but is unreachable from other ipv6 instances on the internet. I...
  3. T

    [Solved] One way routing through VLANs and L3 switches - Brocade ICX7150

    Hi all. I'm sure I'm missing something obvious, but I'm a hardware guy trying to get into a software world. So this may or may not be a super easy fix. I currently run a flat network, 192.168.0.0/24, which I am working to replace entirely with a vlan'd up network, coming soon when my other...
  4. G

    Mellanox 10G Dual-Port card does not do any routing with IPoIB?

    Hey folks, I have 3 servers equipped with the Connect-X2 MT26418, all running Proxmox (debian11). The cards are all 2 Port ones, and I got 2 cables running between them like this: +---------------------------+ | serv1 | +---------------------------+ | Port 2 |...
  5. S

    Basic help / step by step to convert home network to L3 / vlan routing

    I hope I'm phrasing the question right. I've got a configuration in place right now, and I want to reconfigure, but the terms and concepts are confusing me a bit. I only sort of understand the concept and I'm trying to learn this stuff and apply it to my setup. At the moment, my inter-VLAN...
  6. J

    pfSense replacing a Cisco Router - not acting as expected

    Hey all. So I have just replaced my old Cisco 2921 with a little pfSense build on a desktop box with an added 4 port NIC card. All just GB connections, so nothing fancy there. I thought it would just be a case of remove and replace. That didn't seem to work though. Firstly, my entire network...
  7. AveryFreeman

    Setting up routing between 2 different subnets - what are the basics?

    Hey, So this might be kind of complicated - so far it's a bit over my head, but I know it's absolutely possible. I'm trying to set up routing between two subnets with an AD trust between the two of them, but let's put the AD/IPA trust aside for a minute, because none of it will work without...
  8. AveryFreeman

    Accelerated packet pushers, e.g. XDP vs DPDK - what do you use, and why?

    @mmx01 I have a VM running VyOS I'm using as a packet pusher for a storage network. I'd like to offload it to an old E3 board I'm using as an OPNsense router. But my storage network is 40Gbps, and it's impossible for even a fast board to get that kind of throughput, let alone a dual core E3...
  9. N

    EU FS: Brocade MLXE-4-MR2-M-AC IP/MPLS Router for datacenter

    Hi there, i have these 2 similar units that I dont use, nor do i intend to use them at home :) maybe somebody in here would be interested. The units comes without any modules beside the 2* PSU and 4 fans in the rear. (Management and interface modules is needed) My selling price is: 150 each...
  10. Bjorn Smith

    Mellanox SX6018 L3 Routing

    Hi, I have this nice switch that I am really happy with, but I want to start using VLANS. I have created 3 VLANS and want to be able to route traffic between the VLANS. Reading up on it, it seem like you have to do the following: interface ethernet 1/1/2 no switchport force Which sets the...
  11. K

    Unifi with ICX

    Have any of you had any experience with Ubiquiti (Ubnt) gear and the ICX? I am trying to keep the 10gb traffic constrained within the 10gb ports, and only route out when needed to reach a client on the wifi or the internet since the PR01 is connected via 1gb links. I can setup static routes...
  12. D

    Subnetting, Subnet Masks & vLans

    I've always just run everything in my 192.168.x.xxx network, all unmanaged switches, just everything, everywhere. I wanna learn more about selecting subnet masks, IP addresses (10.12.43.114 vs 192.168.1.114 for example), I wanna learn the difference between a subnet and a VLAN, and how traffic...