BootROM version: 1.0.30
Copyright (C) 2011 Brocade Communication.
CPU0: P3041, Version: 2.0, (0x82110320)
Core: E500MC, Version: 3.2, (0x80230032)
Clock Configuration:
CPU0:1500 MHz, CPU1:1500 MHz, CPU2:1500 MHz, CPU3:1500 MHz,
CCB:750 MHz,
DDR:500 MHz (1000 MT/s data rate) (Asynchronous), LBC:46.875 MHz
FMAN1: 375 MHz
PME: 375 MHz
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Model ID: 137
Board: P3041 CASTOR-T, 36-bit Addressing
reset reason was 0x00000001: Power Up
I2C: ready
DRAM: Initializing....
Enabled DHC_EN
DIMM 0 [0xfe008174=0x8675a607] [0xfe008f38=0x0c0e0b0f] [0xfe008f3c=0x0e0b0d0c] [0xfe008f40=0x11004004]
6 GiB left unmapped
DDR: 8 GiB (DDR3, 64-bit, CL=7, ECC on)
testdram value not set, dram test not run
Now running in RAM - U-Boot at: 7ff20000
FLASH: 4 MiB
L2: 128 KB enabled
Corenet Platform Cache: 1024 KB enabled
SERDES: bank 2 disabled
PCI: gd->brcd_flags = 0, PCI init
PCIE1 connected to Slot 1 as Root Complex (base addr fe200000)
Scanning PCI bus 01
PCIE0 on bus 00 - 01
In: serial
Out: serial
Err: serial
SRIO1: disabled
SRIO2: disabled
NVRAM/RTC oscillator already turned on in a previous boot
Net: Fman: Uploading microcode version 101.6.0.
FM1@DTSEC4, FM1@DTSEC5
usb reset 0
(Re)start USB 0...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Hit ESC to stop autoboot: 5 4 3 2 1 0
Loading Environment 0 from NVRAM...
(Re)start USB 0...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
setting prt to 1
Loading file "boot/zImage.tree.initrd" from usb device 0:1 (usbda1)
3538211 bytes read
Loading file "boot/silkworm.dtb" from usb device 0:1 (usbda1)
21396 bytes read
Loading file "boot/hv.uImage" from usb device 0:1 (usbda1)
420128 bytes read
Loading file "boot/silkworm_hct.dtb" from usb device 0:1 (usbda1)
12843 bytes read
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 02000000 ...
Image Name:
Image Type: PowerPC Linux Kernel Image (uncompressed)
Data Size: 420064 Bytes = 410.2 KiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 04000000
Booting using the fdt blob at 0x4000000
Loading Kernel Image ... OK
OK
Loading Device Tree to 00ff7000, end 00fff393 ... OK
=======================================
Freescale Hypervisor 0.8-004
Hypervisor command line: config-addr=0x3000000 p1-linux="root=/dev/sda1 rootfstype=ext4 quiet"
[0] malloc_init: using 31 MiB at 0x7e0b7930 - 0x7fffffff
Device tree compatible: brocade,SILKWORM_PB
[0] dt_read_aliases: Alias pci1 points to non-existent /pcie@ffe201000
[0] dt_read_aliases: Alias sec_jr0 points to non-existent /soc@ffe000000/crypto@300000/jr@1000
[0] dt_read_aliases: Alias sec_jr1 points to non-existent /soc@ffe000000/crypto@300000/jr@2000
[0] dt_read_aliases: Alias sec_jr2 points to non-existent /soc@ffe000000/crypto@300000/jr@3000
[0] dt_read_aliases: Alias sec_jr3 points to non-existent /soc@ffe000000/crypto@300000/jr@4000
[0] dt_read_aliases: Alias rtic_a points to non-existent /soc@ffe000000/crypto@300000/rtic@6000/rtic-a@0
[0] dt_read_aliases: Alias rtic_b points to non-existent /soc@ffe000000/crypto@300000/rtic@6000/rtic-b@20
[0] dt_read_aliases: Alias rtic_c points to non-existent /soc@ffe000000/crypto@300000/rtic@6000/rtic-c@40
[0] dt_read_aliases: Alias rtic_d points to non-existent /soc@ffe000000/crypto@300000/rtic@6000/rtic-d@60
[0] assign_callback: device serial0 in serial0 not found
[0] assign_callback: device /hvcpld in fpga not found
[0] remap_restart_init: undefine restart-maps-to. Setting to remap_restart_unc.
[0] watchdog enabled with period 38
HV> [1] watchdog enabled with period 38
HV> [2] watchdog enabled with period 38
HV> [3] watchdog enabled with period 38
HV> [0] assign_callback: device /soc/memory-controller@9000 in memory-controller@9000 not found
HV> [0] assign_callback: device mdio0 in mdio0 not found
HV> [0] assign_callback: device phy5 in phy5 not found
HV> Bootargs set for cpu = 0 guest p1-linux bootagrs = root=/dev/sda1 rootfstype=ext4 quiet
HV>
part1 ACTIVE
HV> [0] loading binary image from 0x79fff000 to 0x3000000
HV> [0] Loading uImage from 0x78000000 to 0
HV> [0] branching to guest p1-linux, 2 cpus
HV> this is quiet!
end of DRAM 4294967296 memstart_addr0 total_lowmem 4294967296
SLUB: dfree enabled
PRIMING SLUB: main caches
SLUB: export __kmalloc at 0x401068c0 changed to 0x40106c80
SLUB: export vmalloc at 0x400f55a8 changed to 0x400f535c
SLUB: export vfree at 0x400f4748 changed to 0x400f4678
network namespace NR (VRF) started
mdio_bus mdio: /devices/fman0/mdio@f1000/p4080ds-xmdio1 has invalid PHY address
mmod_sysctl_inited: 1
Fman microcode 51 45 46
FMAN microcode UC size 0x1b64
default MII is 0xc10a8000 for tsec0
default MII is 0xc10b0000 for tsec0
Uboot wdt counter value: 0
INIT: version 2.78 booting
e2fsck 1.41.12 (17-May-2010)
/dev/sda1: clean, 16342/122160 files, 172513/488281 blocks
e2fsck 1.41.12 (17-May-2010)
/dev/sda2: recovering journal
/dev/sda2: clean, 6967/122160 files, 124695/488192 blocks
Firmware Integrity Check is default off
Bypassing firmware validation.
mount: sysfs already mounted or /sys busy
mount: according to mtab, none is already mounted on /sys
mknod: /dev/fsl-hv: File exists
Hostname is ETH2
INIT: Entering runlevel: 3
FIPS-mode test application
1. Non-Approved cryptographic operation test...
a. Excluded algorithm (MD5)...successful
b. Included algorithm (D-H)...successful
2. Automatic power-up self test...successful
3. AES-128,192,256 CBC encryption/decryption...successful
4. RSA key generation and encryption/decryption...successful
4.1. RSA 2048 with 'SHA256' testing...successful
5. TDES-CBC encryption/decryption...successful
6a. SHA-1 hash...successful
6b. SHA-256 hash...successful
6c. SHA-512 hash...successful
6d. HMAC-SHA-1 hash...successful
6e. HMAC-SHA-224 hash...successful
6f. HMAC-SHA-256 hash...successful
6g. HMAC-SHA-384 hash...successful
6h. HMAC-SHA-512 hash...successful
7. Non-Approved cryptographic operation test...
a. Excluded algorithm (MD5)...Not executed
b. Included algorithm (D-H)...successful as expected
8. Zero-ization...Successful
9. TLS KDF...successful
10. SSH KDF...successful
All tests completed with 0 errors
Waiting to starting configuration management service
Starting configuration management service
[wmd_init]: chunk_size = 0xa00000
[wmd_init]: Checksum does not match. current_cksum = 0x16c0388f stored_cksum = 0x8fd5a6c1
[wmd_init]: FPGA version = 0x70007445
[wmd_init]: reset_reason = 0x1
[wmd_init]: updated reset_reason = 0x0
Reset reason = 0x1
wmem: b0004000:247439360
tbuf: 8ff00000:536854528
Found 1(threshold 5) abnormal reboots within 3000 seconds window(threshold)
KernelSpace rastrace_register
SWBD module launch ... Sat Oct 16 10:09:59 GMT 2021
Castor: PCIe Err handler init plat_pci_init[636]
bhpc_irq_init: Using default device map. Size 10
pcie_event_isr: ###### virq 174 core 0 MCSR 0x0 MSR 0x10021002 count 1
plat_pcie_error:Last addresses 0x0 0x0 0x0 0x0
0x0 0x0 0x0 0x0
0x0 0x0
CPLD INIT DONE
PCIe Event [UNKNOWN] slot 0 Source Bus 0 Dev 0 MM Parent Bus 0 Dev 0 Events: 1
AQ1402: Loaded Platform 137
MDIO Driver: Name [Freescale P4080DS MDIO Bus], Address [8acaa220]
GPIO CCSR phys addr = 0xffe130000, virt addr = 0xd830a000
cbr_rev_init: pci config word 0xc0220008 for Castors
cbr_rev_init: prs_reg[0].ctrl=0x00000102
cbr_rev_init: chip_rev detected=2
Cobra rev B found
Found Castor-T Type board Blade ID 145
Info: panic dump has been initialized!
Creating L3-L2 fifo Sat Oct 16 10:10:10 GMT 2021 ...
Starting HASM ... Sat Oct 16 10:10:10 GMT 2021
Exisitng reboot reason fsize = 5 rb=
Global Fan Direction: Port Side EXHAUST
Network OS (ETH2)
ETH2 console login: Starting Dcmd ... Sat Oct 16 10:10:19 GMT 2021
Starting Ccmd ... Sat Oct 16 10:10:19 GMT 2021
server starting
Restoring CCM databaseserver starting
Restoring DCM database..tp_register, got none fss tp handle=10000001h
2021/10/16-10:10:24, [HASM-1004], 45336,, INFO, VDX6740T, Processor reloaded - Reset.
........done
....................................waiting for server to shut down..... done
server stopped
...pg_ctl: PID file "/etc/fabos/Dcmd/WaveDatabase/postmaster.pid" does not exist
Is server running?
Dcmd Database is corrupted. Hence, clearing the database.
Sat Oct 16 10:12:54 GMT 2021 :: Confd: Waiting for Dcmd to become ready...
CHASSIS RECOV_ACTIVE
SNMP Research EMANATE/Lite Agent Version 16.2.0.9
Copyright 1989-2006 SNMP Research, Inc.
Sat Oct 16 10:13:09 GMT 2021 :: Triggering confd load phase1 after waiting for 5 secs
pcap_master_init - sm is NULL after ha_calloc
Critical FDB init success
2021/10/16-10:13:22, [BGP-1002], 45337,, INFO, ETH2, BGP: Daemon ready for action
.
Warn: imi_debug :zg->protocol is not set before lib_start()
CMSH called
nsm_client_start - ret = 0
nsm_client_start_resp_socket-2874 Starts ...
message_client_connect_resp_socket-859 ends
nsm_client_start_resp_socket-2894 succeeds.
Activating haml.. l2sys_client_haml_activate
NOS : Initialize DY-SYNC LIB : mgmt_state 34002110
NOS : Init bc_pkt 1024cc54 bc_index 20 ***
***********************************************************
hal_new_link_cb: NSM: initialized system SVI mac: 50:eb:1a:f4:a9:1f
************************************************************
2021/10/16-10:13:30, [NSM-1019], 45338, DCE, INFO, ETH2, Interface Ve 4093 is administratively up.
2021/10/16-10:13:32, [MFIC-1002], 45339,, INFO, ETH2, Chassis FRU header not programmed for switch NID, using defaults (applies only to FICON environments).
2021/10/16-10:13:46, [IPAD-1002], 45340,, INFO, VDX6740T, Switch name has been successfully changed to sw0.
All service instances on Active
2021/10/16-10:13:46, [HASM-1108], 45341,, INFO, VDX6740T, All service instances become active.
2021/10/16-10:13:46, [DCM-1002], 45342,, INFO, VDX6740T, PostBoot processing on global config has started.
2021/10/16-10:13:46, [DOT1-1013], 45343, DCE, INFO, sw0, DOT1X test timeout value is set to 10.
2021/10/16-10:13:46, [ONMD-1002], 45344, DCE, INFO, sw0, LLDP global configuration is changed.
2021/10/16-10:13:46, [ONMD-1002], 45345, DCE, INFO, sw0, LLDP global configuration is changed.
2021/10/16-10:13:47, [EM-1034], 45346,, ERROR, VDX6740T, PS 2 is set to faulty, rc=2000e.
2021/10/16-10:13:48, [RAS-2001], 45347,, INFO, sw0, Audit message log is enabled.
2021/10/16-10:13:48, [RAS-2003], 45348,, INFO, sw0, Audit message class configuration has been changed to SECURITY,CONFIGURATION,FIRMWARE.
DCE Blade: board type 4 Revision 4 Software Model 137
In cbr_chip_cfg_init
In cbr_chip_cfg_init ldev size 2048
In cbr_chip_cfg_init ldev size 0
2021/10/16-10:13:49, [NSM-2014], 45349, DCE, INFO, sw0, VLAN sub-profile for port-profile UpgradedVlanProfile is created.
2021/10/16-10:13:49, [NSM-2017], 45350, DCE, INFO, sw0, Port-profile UpgradedVlanProfile is configured for switching properties.
2021/10/16-10:13:49, [NSM-2019], 45351, DCE, INFO, sw0, The trunk mode is configured for port-profile UpgradedVlanProfile.
2021/10/16-10:13:49, [NSM-2024], 45352, DCE, INFO, sw0, All VLANs are configured as tagged VLANs for port-profile UpgradedVlanProfile.
2021/10/16-10:13:49, [NSM-2044], 45353, DCE, INFO, sw0, Domain: default creation successful.
2021/10/16-10:13:49, [NSM-2046], 45354, DCE, INFO, sw0, Profile: UpgradedVlanProfile addition to domain default successful.
2021/10/16-10:13:49, [RTM-1023], 45355, DCE, INFO, sw0, Route 0.0.0.0/0 pointing to management interface will not be redistributed to other protocols.
.
2021/10/16-10:13:49, [DCM-1003], 45356,, INFO, VDX6740T, PostBoot processing on global config is complete.
FCOE agent in ctor function
2021/10/16-10:13:52, [HASM-1108], 45357,, INFO, VDX6740T, All service instances become active.
Enabling Eth switch... 1
POST1: started running Sat Oct 16 10:13:52 GMT 2021
POST1: Script PASSED with exit status of 0 Sat Oct 16 10:13:52 GMT 2021 took (0:0:0)
POST2: started running Sat Oct 16 10:13:56 GMT 2021
POST2: Test #1 - Running portloopbacktest -dports 1-48 (10G)
POST2: Test #2 - Running portloopbacktest -dports 49-64 (40G)
POST2: Script PASSED with exit status of 0 Sat Oct 16 10:14:03 GMT 2021 took (0:0:7)
LPM Critical Data Size [526336]
NH Critical Data Size [6272]
QOS-TXQ Critical Data Structure Size = [13704]
2021/10/16-10:14:10, [BL-1000], 45358,, INFO, VDX6740T, Initializing ports...
2021/10/16-10:14:12, [BL-1034], 45359,, INFO, VDX6740T, SWITCH CEE initialization completed.
Set VLP module index 0 to module 0
sys_init: before msg_init1
init_dy_sync_slave(), sync_type = 49 >= 49
module_slot_pre_init: setting module # 0 fid_base to: 1774
link is up
2021/10/16-10:14:18, [NSM-1019], 45360, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/1 is administratively up.
2021/10/16-10:14:18, [NSM-1019], 45361, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/2 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45362, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/3 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45363, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/4 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45364, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/5 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45365, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/6 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45366, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/7 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45367, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/8 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45368, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/9 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45369, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/10 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45370, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/11 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45371, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/12 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45372, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/13 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45373, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/14 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45374, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/15 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45375, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/16 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45376, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/17 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45377, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/18 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45378, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/19 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45379, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/20 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45380, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/21 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45381, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/22 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45382, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/23 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45383, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/24 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45384, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/25 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45385, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/26 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45386, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/27 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45387, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/28 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45388, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/29 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45389, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/30 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45390, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/31 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45391, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/32 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45392, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/33 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45393, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/34 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45394, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/35 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45395, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/36 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45396, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/37 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45397, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/38 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45398, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/39 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45399, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/40 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45400, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/41 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45401, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/42 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45402, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/43 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45403, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/44 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45404, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/45 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45405, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/46 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45406, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/47 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45407, DCE, INFO, sw0, Interface TenGigabitEthernet 7/0/48 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45408, DCE, INFO, sw0, Interface FortyGigabitEthernet 7/0/49 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45409, DCE, INFO, sw0, Interface FortyGigabitEthernet 7/0/50 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45410, DCE, INFO, sw0, Interface FortyGigabitEthernet 7/0/51 is administratively up.
2021/10/16-10:14:19, [NSM-1019], 45411, DCE, INFO, sw0, Interface FortyGigabitEthernet 7/0/52 is administratively up.
2021/10/16-10:14:40, [DCM-1002], 45412,, INFO, VDX6740T, PostBoot processing on L0 config has started.
2021/10/16-10:14:54, [HASM-1111], 45413,, INFO, VDX6740T, Configuration replay has completed on SWITCH.
2021/10/16-10:14:54, [DCM-1003], 45414,, INFO, VDX6740T, PostBoot processing on L0 config is complete.
2021/10/16-10:14:54, [DCM-1004], 45415,, INFO, VDX6740T, Configuration File Replay has started.
2021/10/16-10:15:00, [IPAD-1002], 45416,, INFO, VDX6740T, Switch name has been successfully changed to ETH2.
2021/10/16-10:15:02, [SNMP-1005], 45417,, INFO, ETH2, SNMP configuration attribute, community string 1 , [ConvergedNetwork] has been added.
2021/10/16-10:15:03, [SNMP-1005], 45418,, INFO, ETH2, SNMP configuration attribute, community string 2 , [OrigEquipMfr] has been added.
2021/10/16-10:15:03, [SNMP-1005], 45419,, INFO, ETH2, SNMP configuration attribute, Access 2 , has changed from [false] to [true].
2021/10/16-10:15:03, [SNMP-1005], 45420,, INFO, ETH2, SNMP configuration attribute, community string 3 , [Secret C0de] has been added.
2021/10/16-10:15:03, [SNMP-1005], 45421,, INFO, ETH2, SNMP configuration attribute, Access 3 , has changed from [false] to [true].
2021/10/16-10:15:03, [SNMP-1005], 45422,, INFO, ETH2, SNMP configuration attribute, community string 4 , [common] has been added.
2021/10/16-10:15:04, [SNMP-1005], 45423,, INFO, ETH2, SNMP configuration attribute, community string 5 , [private] has been added.
2021/10/16-10:15:04, [SNMP-1005], 45424,, INFO, ETH2, SNMP configuration attribute, Access 5 , has changed from [false] to [true].
2021/10/16-10:15:04, [SNMP-1005], 45425,, INFO, ETH2, SNMP configuration attribute, community string 6 , [public] has been added.
2021/10/16-10:15:04, [SNMP-1005], 45426,, INFO, ETH2, SNMP configuration attribute, SNMPv3 User Name 1, [snmpadmin1] has been added.
2021/10/16-10:15:05, [SNMP-1005], 45427,, INFO, ETH2, SNMP configuration attribute, SNMPv3 User Name 2, [snmpadmin2] has been added.
2021/10/16-10:15:05, [SNMP-1005], 45428,, INFO, ETH2, SNMP configuration attribute, SNMPv3 User Name 3, [snmpadmin3] has been added.
2021/10/16-10:15:05, [SNMP-1005], 45429,, INFO, ETH2, SNMP configuration attribute, SNMPv3 User Name 4, [snmpuser1] has been added.
2021/10/16-10:15:06, [SNMP-1005], 45430,, INFO, ETH2, SNMP configuration attribute, SNMPv3 User Name 5, [snmpuser2] has been added.
2021/10/16-10:15:06, [SNMP-1005], 45431,, INFO, ETH2, SNMP configuration attribute, SNMPv3 User Name 6, [snmpuser3] has been added.
2021/10/16-10:15:09, [FW-1424], 45432,, WARNING, ETH2, Switch status changed from HEALTHY to MARGINAL.
2021/10/16-10:15:09, [FW-1427], 45433,, WARNING, ETH2, Switch status change contributing factor Power supply: 1 bad.
2021/10/16-10:15:13, [NSM-1010], 45434, DCE, INFO, ETH2, InterfaceMode changed from None to L2 for interface TenGigabitEthernet 7/0/3.
2021/10/16-10:15:13, [NSM-1011], 45435, DCE, INFO, ETH2, OperationalEndpointMode changed from None to Access for interface TenGigabitEthernet 7/0/3.
2021/10/16-10:15:14, [NSM-1010], 45436, DCE, INFO, ETH2, InterfaceMode changed from None to L2 for interface TenGigabitEthernet 7/0/5.
2021/10/16-10:15:14, [NSM-1011], 45437, DCE, INFO, ETH2, OperationalEndpointMode changed from None to Access for interface TenGigabitEthernet 7/0/5.
2021/10/16-10:15:15, [NSM-1020], 45438, DCE, INFO, ETH2, Interface TenGigabitEthernet 7/0/5 is administratively down.
2021/10/16-10:15:19, [NSM-1010], 45439, DCE, INFO, ETH2, InterfaceMode changed from None to L2 for interface TenGigabitEthernet 7/0/20.
2021/10/16-10:15:19, [NSM-1011], 45440, DCE, INFO, ETH2, OperationalEndpointMode changed from None to Access for interface TenGigabitEthernet 7/0/20.
2021/10/16-10:15:20, [NSM-1010], 45441, DCE, INFO, ETH2, InterfaceMode changed from None to L2 for interface TenGigabitEthernet 7/0/21.
2021/10/16-10:15:20, [NSM-1011], 45442, DCE, INFO, ETH2, OperationalEndpointMode changed from None to Access for interface TenGigabitEthernet 7/0/21.
2021/10/16-10:15:21, [NSM-1010], 45443, DCE, INFO, ETH2, InterfaceMode changed from None to L2 for interface TenGigabitEthernet 7/0/22.
2021/10/16-10:15:21, [NSM-1011], 45444, DCE, INFO, ETH2, OperationalEndpointMode changed from None to Access for interface TenGigabitEthernet 7/0/22.
2021/10/16-10:15:22, [NSM-1010], 45445, DCE, INFO, ETH2, InterfaceMode changed from None to L2 for interface TenGigabitEthernet 7/0/23.
2021/10/16-10:15:22, [NSM-1011], 45446, DCE, INFO, ETH2, OperationalEndpointMode changed from None to Access for interface TenGigabitEthernet 7/0/23.
2021/10/16-10:15:23, [NSM-1010], 45447, DCE, INFO, ETH2, InterfaceMode changed from None to L2 for interface TenGigabitEthernet 7/0/24.
2021/10/16-10:15:23, [NSM-1011], 45448, DCE, INFO, ETH2, OperationalEndpointMode changed from None to Access for interface TenGigabitEthernet 7/0/24.
2021/10/16-10:15:24, [NSM-1010], 45449, DCE, INFO, ETH2, InterfaceMode changed from None to L2 for interface TenGigabitEthernet 7/0/25.
2021/10/16-10:15:24, [NSM-1011], 45450, DCE, INFO, ETH2, OperationalEndpointMode changed from None to Access for interface TenGigabitEthernet 7/0/25.
2021/10/16-10:15:25, [NSM-1010], 45451, DCE, INFO, ETH2, InterfaceMode changed from None to L2 for interface TenGigabitEthernet 7/0/26.
2021/10/16-10:15:25, [NSM-1011], 45452, DCE, INFO, ETH2, OperationalEndpointMode changed from None to Access for interface TenGigabitEthernet 7/0/26.
2021/10/16-10:15:26, [NSM-1010], 45453, DCE, INFO, ETH2, InterfaceMode changed from None to L2 for interface TenGigabitEthernet 7/0/27.
2021/10/16-10:15:26, [NSM-1011], 45454, DCE, INFO, ETH2, OperationalEndpointMode changed from None to Access for interface TenGigabitEthernet 7/0/27.
2021/10/16-10:15:27, [NSM-1010], 45455, DCE, INFO, ETH2, InterfaceMode changed from None to L2 for interface TenGigabitEthernet 7/0/28.
2021/10/16-10:15:27, [NSM-1011], 45456, DCE, INFO, ETH2, OperationalEndpointMode changed from None to Access for interface TenGigabitEthernet 7/0/28.
2021/10/16-10:15:28, [NSM-1010], 45457, DCE, INFO, ETH2, InterfaceMode changed from None to L2 for interface TenGigabitEthernet 7/0/29.
2021/10/16-10:15:28, [NSM-1011], 45458, DCE, INFO, ETH2, OperationalEndpointMode changed from None to Access for interface TenGigabitEthernet 7/0/29.
2021/10/16-10:15:29, [NSM-1010], 45459, DCE, INFO, ETH2, InterfaceMode changed from None to L2 for interface TenGigabitEthernet 7/0/30.
2021/10/16-10:15:29, [NSM-1011], 45460, DCE, INFO, ETH2, OperationalEndpointMode changed from None to Access for interface TenGigabitEthernet 7/0/30.
2021/10/16-10:15:30, [NSM-1010], 45461, DCE, INFO, ETH2, InterfaceMode changed from None to L2 for interface TenGigabitEthernet 7/0/31.
2021/10/16-10:15:30, [NSM-1011], 45462, DCE, INFO, ETH2, OperationalEndpointMode changed from None to Access for interface TenGigabitEthernet 7/0/31.
2021/10/16-10:15:35, [NSM-1010], 45463, DCE, INFO, ETH2, InterfaceMode changed from None to L2 for interface TenGigabitEthernet 7/0/47.
2021/10/16-10:15:35, [NSM-1011], 45464, DCE, INFO, ETH2, OperationalEndpointMode changed from None to Access for interface TenGigabitEthernet 7/0/47.
2021/10/16-10:15:57, [DCM-1005], 45465,, INFO, VDX6740T, Configuration Replay is complete.
2021/10/16-10:15:57, [SEC-1334], 45466,, INFO, VDX6740T, local security policy not saved.
2021/10/16-10:15:57, [SEC-1334], 45467,, INFO, VDX6740T, local security policy not saved.
2021/10/16-10:15:58, [SEC-1197], 45468,, INFO, VDX6740T, Changed account admin.
2021/10/16-10:15:59, [HASM-1110], 45469,, INFO, VDX6740T, Configuration replay has completed on the system.
2021/10/16-10:15:59, [DCM-1116], 45470,, INFO, VDX6740T, System initialization is complete. NOS is ready to handle all commands.
2021/10/16-10:15:59, [SEC-1197], 45471,, INFO, VDX6740T, Changed account user.