Did you somehow solve the problem with the driver for i226-V? And also how were you able to install the driver for RZ616?
Minisforum MS-01 PCIe Card and RAM Compatibility Thread
- Thread starter Patrick
- Start date
Notice: Page may contain affiliate links for which we may earn a small commission through services like Amazon Affiliates or Skimlinks.
Never had a single crash since i bought it .. i even never updated the bios also .. still the original one (1.17 i think)
I have the MS-01 with the 12900H and 96gb of ram.
MCX512A-ACAT Mellanox Technologies MT27800 Family [ConnectX-5] 10/25Gb PCI-e card is working fine in proxmox - pfsense via Passthrough
Now only problem will be a heat but, i will print Mellanox ConnectX-2 40mm fan bracket by Citruspers | Download free STL model | Printables.com and then some 40mm fan will land on it.
Now only problem will be a heat but, i will print Mellanox ConnectX-2 40mm fan bracket by Citruspers | Download free STL model | Printables.com and then some 40mm fan will land on it.
Same happened to me last week.
Minisforum support instructed me to disconnect drives and ram and clear the cmos but it hasn’t made any difference.
They agreed to replace the unit
I just sent it yesterday, lets’s see how long it takes to get a replacement.
Is this a pattern?
Seems to be a pattern. My 12900H turned off one day and then refused to turn on too. Even after disconnecting the CMOS battery for 24hrs.
I was using the default HW that came with the MS-01. No extras/GPU etc. Just an out-of-the blue dead PC...
After a lengthy wait via email I eventually got through to support and got the device RMA'd.
Just got an email yesterday to say a replacement is on the way... It's a little concerning that the devices are failing with little to no correlation as to what is causing the failure.
There are no issues with the PSU it's been tested and working well beyond the 14W that my MS-01 was consuming during idle and the 28W under load...
Can someone from ServeTheHome try to get a better explanation from minisforum what the failure point is and how they intend to resolve it?
"have the server plugged into a smart plug with energy. I set it to power off between 23:04 and 23:15 only if the power levels dip below 5 watts for 2 minutes. After 5 minutes it powers back on. (Set the BIOS to always power on on power restoral)
unfortunately I have had to resort to similar. I do not have access to the beta firmware to adjust memory speed, I have 96gb mushkin memory, and server would crash every 2-3 days. I hooked up to a smart plug, and do a cronjob to backup all LXC's at 3:45 am, power down the node at 3:50, turn the power off at 3:55 and then power back on at 4:00 am.
works but id rather have a stable system.
unfortunately I have had to resort to similar. I do not have access to the beta firmware to adjust memory speed, I have 96gb mushkin memory, and server would crash every 2-3 days. I hooked up to a smart plug, and do a cronjob to backup all LXC's at 3:45 am, power down the node at 3:50, turn the power off at 3:55 and then power back on at 4:00 am.
works but id rather have a stable system.
Have this one working without hicks, connected to a zx-swtg124as switch
for me 2x UBIQUITI UC-DAC-SFP+ DAC SFP+ MODULE 10G 0.5M DIRECT ATTACH COPPER CABLE
and Mikrotik CRS309-1G-8S+
Anyone try high capacity M.2 SSD's like this one? https://www.amazon.com/Corsair-MP600-PCIe-Gen4-NVMe/dp/B0BJKV2MZ6/
I think they pretty much all work bellow a certain length as they are simply wired and not active
I believe someone managed to install this by using a higher post and leaving the NVME SSD in angle but without a fan, do a search in this thread first
Im looking for a reliable power supply to use with the MS-01 with a GPU added. I guess i need a minimum of 240W if I add an Arc A310?
Has anybody tried this already and which power supply did they use?
Has anybody tried this already and which power supply did they use?