Build’s Name: AMD is back (Noctua fanboy edition)
Operating System/ Storage Platform: OpenSuse (Tumbleweed)
CPU: 2x AMD Epyc 7301
Motherboard: Supermicro H11DSi
Chassis: Nanoxia Deep Silence 2
Drives: Crucual MX100 512GB, 4x Intel S3500 800GB (RAID0), HDDs undecided, probably 4x WD red RAID5
RAM: 16x16GB Samsung 2Rx4 DDR4-2133 reg ECC (still hoping to hit 2400 MT/s)
Add-in Cards: Nvidia GTX 960 4GB
Power Supply: Seasonic Focus Platinum 850W
Other Bits: 2x Noctua NH-U14S TR4-SP3 CPU coolers, lots of fans. I am a big fan of air cooling.
Usage Profile: Mostly fluid simulation stuff and code development. All my solvers are memory bandwidth limited, hence AMD Epyc. The RAID0 will serve as a scratch drive to save and work with large transient result files when creating animations.
I know that faster memory would have been better. But most of the workstation consists of parts I already had or could source very cheap. Memory might be upgraded once the prices normalize.
Getting the parts (specifically CPUs and mainboard) was quite an ordeal. Would have started this build much earlier if they had been available. But now they are all here and I am trying to get it to run. Looking good so far.
Edit1: first issues
1) I was aware of this from previous builds, but still worth noting: Supermicro refuses to use standard ATX mounting holes even for their workstation boards they label as "E-ATX". So a few holes needed to be added to the motherboard tray of the case.
2) Cables of the power supply (24pin ATX and 8pin EPS) are too short for proper cable management behind the board. Already ordered some extension cables.
3) Again Supermicro: the motherboard has issues with these slow-spinning Noctua fans. They idle at around 300 rpm which causes the motherboard to flash a red LED and rev up all fans to maximum speed in an interval of ~10s. When I disconnect the fans and run the coolers passively, everything works fine and temperatures are ok. Will contact SM for a bios update request that adds "ignore fan failure" options or allows for slow-spinning fans.
4) Poor performance under windows 10 pro. I like to use a windows test installation while setting up new machines to have a different OS for cross-checks. Cinebench yields ~4000 points, I would have expected somewhere above 5000 points for these CPUs. Will check if windows server 2016 runs better.
5) Does not post with memory speed set to DDR4-2400. Will have to check again when new bios versions are released.
Edit2: lessons learned
So fan control issues could be resolved, however the lack of fan control through bios options still baffles me. If I had any other choice Supermicro would not have made the cut. Their support was not particularly helpful either. The motherboard has a few design flaws. The m.2 slot only gets 2 PCIe lanes, no USB3 header, only two PCIe x16 slots...
I will consider changing the motherboard once ASRock rack releases their dual SP3 lineup. They mentioned availability in Q2 2018.
The case is cheap, and it shows. OK, you can't expect much for 80€. but the material is paper-thin, parts barely fit and hold together due to loose tolerances and even mounting the side panels is a challenge unless you have 4 hands or lay the case flat on its side. I already had a similar case from this brand with similar issues. However, there are not many alternatives on the market that have a similar small footprint and the same expansion options. I feel like there is a compact case missing on the market with no window side panel, E-ATX compatibility, no wasted space for optical drives and room for ~8-10 3.5"/2.5" drives. For a less compact case I would recommend Fractal Design Define XL. It is of much higher quality.
Apart from these issues I am pretty pleased with the comeback that AMD has made with these Epyc processors, they deliver exactly what I need at a very competitive price. Too bad availability is still an issue.
Until the system is put to its intended use in Q1 2018, time to mine some Aeon to offset the price.
Operating System/ Storage Platform: OpenSuse (Tumbleweed)
CPU: 2x AMD Epyc 7301
Motherboard: Supermicro H11DSi
Chassis: Nanoxia Deep Silence 2
Drives: Crucual MX100 512GB, 4x Intel S3500 800GB (RAID0), HDDs undecided, probably 4x WD red RAID5
RAM: 16x16GB Samsung 2Rx4 DDR4-2133 reg ECC (still hoping to hit 2400 MT/s)
Add-in Cards: Nvidia GTX 960 4GB
Power Supply: Seasonic Focus Platinum 850W
Other Bits: 2x Noctua NH-U14S TR4-SP3 CPU coolers, lots of fans. I am a big fan of air cooling.
Usage Profile: Mostly fluid simulation stuff and code development. All my solvers are memory bandwidth limited, hence AMD Epyc. The RAID0 will serve as a scratch drive to save and work with large transient result files when creating animations.
I know that faster memory would have been better. But most of the workstation consists of parts I already had or could source very cheap. Memory might be upgraded once the prices normalize.
Getting the parts (specifically CPUs and mainboard) was quite an ordeal. Would have started this build much earlier if they had been available. But now they are all here and I am trying to get it to run. Looking good so far.
Edit1: first issues
1) I was aware of this from previous builds, but still worth noting: Supermicro refuses to use standard ATX mounting holes even for their workstation boards they label as "E-ATX". So a few holes needed to be added to the motherboard tray of the case.
2) Cables of the power supply (24pin ATX and 8pin EPS) are too short for proper cable management behind the board. Already ordered some extension cables.
3) Again Supermicro: the motherboard has issues with these slow-spinning Noctua fans. They idle at around 300 rpm which causes the motherboard to flash a red LED and rev up all fans to maximum speed in an interval of ~10s. When I disconnect the fans and run the coolers passively, everything works fine and temperatures are ok. Will contact SM for a bios update request that adds "ignore fan failure" options or allows for slow-spinning fans.
4) Poor performance under windows 10 pro. I like to use a windows test installation while setting up new machines to have a different OS for cross-checks. Cinebench yields ~4000 points, I would have expected somewhere above 5000 points for these CPUs. Will check if windows server 2016 runs better.
5) Does not post with memory speed set to DDR4-2400. Will have to check again when new bios versions are released.
Edit2: lessons learned
So fan control issues could be resolved, however the lack of fan control through bios options still baffles me. If I had any other choice Supermicro would not have made the cut. Their support was not particularly helpful either. The motherboard has a few design flaws. The m.2 slot only gets 2 PCIe lanes, no USB3 header, only two PCIe x16 slots...
I will consider changing the motherboard once ASRock rack releases their dual SP3 lineup. They mentioned availability in Q2 2018.
The case is cheap, and it shows. OK, you can't expect much for 80€. but the material is paper-thin, parts barely fit and hold together due to loose tolerances and even mounting the side panels is a challenge unless you have 4 hands or lay the case flat on its side. I already had a similar case from this brand with similar issues. However, there are not many alternatives on the market that have a similar small footprint and the same expansion options. I feel like there is a compact case missing on the market with no window side panel, E-ATX compatibility, no wasted space for optical drives and room for ~8-10 3.5"/2.5" drives. For a less compact case I would recommend Fractal Design Define XL. It is of much higher quality.
Apart from these issues I am pretty pleased with the comeback that AMD has made with these Epyc processors, they deliver exactly what I need at a very competitive price. Too bad availability is still an issue.
Until the system is put to its intended use in Q1 2018, time to mine some Aeon to offset the price.
Last edited: