Search results

Thanks for the offer @Marc_ I found a way via the bootrom prompt. cheers

No password to get in, @Marc_ . It was purchased on eBay, and the seller did not factory reset the switch. I've got to the BootRom; however, the x440 G1 does not support the "config none" command. The only way I've found is to TFTP a new image, which is the file I am requesting. Cheers

Hello all, I just picked up an Extreme Networks Summit X440-24P from eBay. I am locked out of the console. Does anyone have an EXOS image to share? The last available was "summitX-16.2.5.4-patch1-30-LegacyCLI.xmod" Extreme support won't send it to me as the switch is considered obsolete. Thank...

I have the following: DM me.

The last time I looked BMC V3.58, BIOS 3B14, CMC 3.14.

Hi all, Back again. I hope everyone is well. Has anyone successfully controlled the fan speed on the PSUs on the Quanta - D51PH? I can control the six (6) onboard fans via IPMI commands. The PSUs are another story. The two fans are pinned at 13,325 RPM. Any help would be much appreciated...

I made one. Cost pennies.

Hi all, Anyone have a source for a mating cable? Cheers, Bob

Some work and some don't. After trial and error version that worked for me is 007.1312.0000.0000 available on the Broadcom website.

Yes, it can be had here: Download Center | QCT- Quanta Cloud Technology

I finally tried different versions. StorCLI version 007.1312.0000.0000 finally worked.

Indeed.

@DuDu , success here to. The Expander had to be update to 1.08.0 inorder for the BIOS to update to 3B14.04. Cheers.

What version of the Storcli.efi do you have? The ones I've tried do not see the 3008 controller . Thanks.

Yes, I have windows server 2019 on an SSD. Very strange. @DuDu, I've been digging. I may have found the issue. " Before updating BIOS to 3A13 or later version, Check BMC FW is newer than 3.31 and Expander FW is newer than 1.08 The system may hang on POST if the above FW version is...

I used WinPE to go from S2P_3B04 to S2P_3B14.02, exactly as you did. The system hangs on boot, but BMC is alive. I had to down grade to S2P_3B04 via BMC. Tried to upgrade to S2P_3B14.02 via BMC, but after boot system won't post. Waited of 10 minutes. I had to revert back to S2P_3B04. Last night...

Yes, @RolloZ170 cold boot, disconnected both PSUs. I'm able to roll back to S2P_3B04 via BMC. I just received S2P_3B08.08 which works as well through BMC.

@DuDu I tried to go from S2P_3B04 to S2P_3B14.02 like you did, and it did not work. I ran the two command files as you did, and it seemed to work. After reboot, it did not come up. I had to reflash to S2P_3B04 to get the system to start. Any ideas? What was your initial BIOS before your update?

Bravo! Excellent news. Enjoy.

Did you ever find a cable? I have the same issue. Found this kit on amazon. https://www.amazon.ca/1-25mm-Connectors-Pre-Crimped-Pixhawk-Silicone/dp/B07S18D3RN/ref=sr_1_6?crid=3QPONC1VHNEK9&keywords=1254+molex&qid=1672754713&sprefix=1254+molex%2Caps%2C69&sr=8-6 Cheers