VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 160k init
init started: BusyBox v1.12.2 (2008-11-21 12:20:36 IST)
starting pid 15, tty '': '/etc/rc.d/rcS'
mount: no /proc/mounts
Mounting /proc and /sys
Mounting filesysEXT2-fs warning: checktime reached, running e2fsck is recommended
tems
Loading module Voltaire
Starting crond:
Starting telnetd:
ibsw-init.sh start...
Thu Jun 27 11:52:14 UTC 2019
INSTALL FLAG 0x0
starting syslogd & klogd ...
Starting ISR: ib_is4 0000:81:00.0: ep0_dev_name 0000:81:00.0
starting pid 73
4036 Version 3.1.0 BUILD ID 718
Tue Aug 10 12:41:37 IDT 2010
4036-8302 login: admin
Password:
Welcome to Voltaire Switch 4036-8302
4036-8302# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
cable-config show Shows the cable configuration
clock show Shows the system clock
config Changes to Configuration mode
debug Change to debug mode
disable Changes to Guest mode
end Ends the CLI
exit Exits to previous menu
front show Shows the blade module information at the front of the c
hassis
health-monitor Changes to Health Monitor mode
info-led set Sets the info-led state
info-led show Shows the info-led state
logs Changes to display logs menu
module-firmware show Shows modules firmware information
password update Changes the admin or the enable password
ping Sends ping messages
reload Restarts the switch software
remote show Shows the remote client configuration
route default-gw show Shows the default gateway IP address
sm-info show Shows the SM parameters
temperature show Shows the board temperature in Celsius and Fahrenheit
update firmware chassis Updates the firmware version (embedded in the software u
pdate) using previously defined server name, user name,
and password
update software chassis Updates the software version using previously defined se
rver name, user name, and password
utilities Changes to switch debug Utilities mode
version show Shows software version information
4036-8302# version show
version: 3.1.0
date: Aug 10 2010 12:34:20 PM
build Id:718
4036-8302# utilities
4036-8302(utilities)# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
end Ends the CLI
exit Exits to previous menu
ibaddr Shows the lid and GID addresses of the specified port
ibcheckerrors Scans the network to validate the connectivity
ibcheckerrs Validate IB port (or node) and report errors in counters above t
hreshold
ibchecknet Scans the network to validate the connectivity
ibcheckwidth Scans the network to validate the active link widths
ibclearcounters Clears the PMA port counters
ibclearerrors Clears the PMA error counters in PortCounters
ibhosts Extracts the CA nodes
ibnetdiscover Performs IB subnet discovery
ibportstate Queried the port state and port physical state of an IB port
ibswitches Extracts the IB switches
ibtracert Trace the path from a source GID/LID to a destination GID/LID
perfquery Obtain the PortCounters (basic performance and error counters) f
rom the PMA at the node specified
port-verify Performs a port-verify command
saquery Issue some SA queries
smpquery Allows a basic subset of standard SMP queries
vendstat Queries vendor-specific information of a switch LID
4036-8302(utilities)# exit
4036-8302# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
cable-config show Shows the cable configuration
clock show Shows the system clock
config Changes to Configuration mode
debug Change to debug mode
disable Changes to Guest mode
end Ends the CLI
exit Exits to previous menu
front show Shows the blade module information at the front of the c
hassis
health-monitor Changes to Health Monitor mode
info-led set Sets the info-led state
info-led show Shows the info-led state
logs Changes to display logs menu
module-firmware show Shows modules firmware information
password update Changes the admin or the enable password
ping Sends ping messages
reload Restarts the switch software
remote show Shows the remote client configuration
route default-gw show Shows the default gateway IP address
sm-info show Shows the SM parameters
temperature show Shows the board temperature in Celsius and Fahrenheit
update firmware chassis Updates the firmware version (embedded in the software u
pdate) using previously defined server name, user name,
and password
update software chassis Updates the software version using previously defined se
rver name, user name, and password
utilities Changes to switch debug Utilities mode
version show Shows software version information
4036-8302# config
4036-8302(config)# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
ccm Changes to ccm mode
end Ends the CLI
exit Exits to previous menu
factory-default Switches back to factory default, and reboots the system
fca Changes to FCA configuration mode
interface Changes to interface configuration mode
names Changes to names configuration mode
ntp Changes to ntp configuration mode
ping Sends ping messages
pm Changes to PM configuration mode
policy Changes to Policy mode
port Changes to port configuration mode
remote Changes to remote configuration mode
security Changes to security configuration mode
sm Changes to SM configuration mode
snmp Changes to SNMP configuration mode
4036-8302(config)# interface
4036-8302(config-if)# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
broadcast set Sets the broadcast address
default-gw delete Deletes the default gateway for the interface
default-gw set Sets the default gateway for the interface
dhcp set Enables/disables the DHCP client
end Ends the CLI
exit Exits to previous menu
interface ethernet set Sets Ethernet as the Management interface
interface infiniband set Sets InfiniBand as the Management interface
ip-address set Sets the interface IP address
ip-address show Shows the interface IP address and configuration
link-speed set Sets the interface IP link speed
ping Sends ping messages
4036-8302(config-if)# ip-address show
port selection Ethernet
ip unconnected - interface is down
mask 255.255.255.0
broadcast 192.168.43.255
DHCP client enabled
Link-speed auto-negotiation
4036-8302(config-if)# ip-address show
port selection Ethernet
ip 192.168.0.2
mask 255.255.255.0
broadcast 192.168.0.255
DHCP client enabled
Link-speed auto-negotiation
4036-8302(config-if)# exit
4036-8302(config)# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
ccm Changes to ccm mode
end Ends the CLI
exit Exits to previous menu
factory-default Switches back to factory default, and reboots the system
fca Changes to FCA configuration mode
interface Changes to interface configuration mode
names Changes to names configuration mode
ntp Changes to ntp configuration mode
ping Sends ping messages
pm Changes to PM configuration mode
policy Changes to Policy mode
port Changes to port configuration mode
remote Changes to remote configuration mode
security Changes to security configuration mode
sm Changes to SM configuration mode
snmp Changes to SNMP configuration mode
4036-8302(config)# exit
4036-8302# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
cable-config show Shows the cable configuration
clock show Shows the system clock
config Changes to Configuration mode
debug Change to debug mode
disable Changes to Guest mode
end Ends the CLI
exit Exits to previous menu
front show Shows the blade module information at the front of the c
hassis
health-monitor Changes to Health Monitor mode
info-led set Sets the info-led state
info-led show Shows the info-led state
logs Changes to display logs menu
module-firmware show Shows modules firmware information
password update Changes the admin or the enable password
ping Sends ping messages
reload Restarts the switch software
remote show Shows the remote client configuration
route default-gw show Shows the default gateway IP address
sm-info show Shows the SM parameters
temperature show Shows the board temperature in Celsius and Fahrenheit
update firmware chassis Updates the firmware version (embedded in the software u
pdate) using previously defined server name, user name,
and password
update software chassis Updates the software version using previously defined se
rver name, user name, and password
utilities Changes to switch debug Utilities mode
version show Shows software version information
4036-8302# module-firmware show
Module No. Type Node GUID LID FW Version SW Version
---------- ---- --------- --- ---------- ----------
4036/2036 3.1.0-718
---------
CPLD 1 0x9
IS4 1 0x0008f10500108302 1 7.3.100 VLT1210031300
---------
4036-8302# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
cable-config show Shows the cable configuration
clock show Shows the system clock
config Changes to Configuration mode
debug Change to debug mode
disable Changes to Guest mode
end Ends the CLI
exit Exits to previous menu
front show Shows the blade module information at the front of the c
hassis
health-monitor Changes to Health Monitor mode
info-led set Sets the info-led state
info-led show Shows the info-led state
logs Changes to display logs menu
module-firmware show Shows modules firmware information
password update Changes the admin or the enable password
ping Sends ping messages
reload Restarts the switch software
remote show Shows the remote client configuration
route default-gw show Shows the default gateway IP address
sm-info show Shows the SM parameters
temperature show Shows the board temperature in Celsius and Fahrenheit
update firmware chassis Updates the firmware version (embedded in the software u
pdate) using previously defined server name, user name,
and password
update software chassis Updates the software version using previously defined se
rver name, user name, and password
utilities Changes to switch debug Utilities mode
version show Shows software version information
4036-8302# utilities
4036-8302(utilities)# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
end Ends the CLI
exit Exits to previous menu
ibaddr Shows the lid and GID addresses of the specified port
ibcheckerrors Scans the network to validate the connectivity
ibcheckerrs Validate IB port (or node) and report errors in counters above t
hreshold
ibchecknet Scans the network to validate the connectivity
ibcheckwidth Scans the network to validate the active link widths
ibclearcounters Clears the PMA port counters
ibclearerrors Clears the PMA error counters in PortCounters
ibhosts Extracts the CA nodes
ibnetdiscover Performs IB subnet discovery
ibportstate Queried the port state and port physical state of an IB port
ibswitches Extracts the IB switches
ibtracert Trace the path from a source GID/LID to a destination GID/LID
perfquery Obtain the PortCounters (basic performance and error counters) f
rom the PMA at the node specified
port-verify Performs a port-verify command
saquery Issue some SA queries
smpquery Allows a basic subset of standard SMP queries
vendstat Queries vendor-specific information of a switch LID
4036-8302(utilities)# exit
4036-8302# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
cable-config show Shows the cable configuration
clock show Shows the system clock
config Changes to Configuration mode
debug Change to debug mode
disable Changes to Guest mode
end Ends the CLI
exit Exits to previous menu
front show Shows the blade module information at the front of the c
hassis
health-monitor Changes to Health Monitor mode
info-led set Sets the info-led state
info-led show Shows the info-led state
logs Changes to display logs menu
module-firmware show Shows modules firmware information
password update Changes the admin or the enable password
ping Sends ping messages
reload Restarts the switch software
remote show Shows the remote client configuration
route default-gw show Shows the default gateway IP address
sm-info show Shows the SM parameters
temperature show Shows the board temperature in Celsius and Fahrenheit
update firmware chassis Updates the firmware version (embedded in the software u
pdate) using previously defined server name, user name,
and password
update software chassis Updates the software version using previously defined se
rver name, user name, and password
utilities Changes to switch debug Utilities mode
version show Shows software version information
4036-8302# config
4036-8302(config)# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
ccm Changes to ccm mode
end Ends the CLI
exit Exits to previous menu
factory-default Switches back to factory default, and reboots the system
fca Changes to FCA configuration mode
interface Changes to interface configuration mode
names Changes to names configuration mode
ntp Changes to ntp configuration mode
ping Sends ping messages
pm Changes to PM configuration mode
policy Changes to Policy mode
port Changes to port configuration mode
remote Changes to remote configuration mode
security Changes to security configuration mode
sm Changes to SM configuration mode
snmp Changes to SNMP configuration mode
4036-8302(config)# interface
4036-8302(config-if)# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
broadcast set Sets the broadcast address
default-gw delete Deletes the default gateway for the interface
default-gw set Sets the default gateway for the interface
dhcp set Enables/disables the DHCP client
end Ends the CLI
exit Exits to previous menu
interface ethernet set Sets Ethernet as the Management interface
interface infiniband set Sets InfiniBand as the Management interface
ip-address set Sets the interface IP address
ip-address show Shows the interface IP address and configuration
link-speed set Sets the interface IP link speed
ping Sends ping messages
4036-8302(config-if)# interface ethernet set
4036-8302(config-if)# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
broadcast set Sets the broadcast address
default-gw delete Deletes the default gateway for the interface
default-gw set Sets the default gateway for the interface
dhcp set Enables/disables the DHCP client
end Ends the CLI
exit Exits to previous menu
interface ethernet set Sets Ethernet as the Management interface
interface infiniband set Sets InfiniBand as the Management interface
ip-address set Sets the interface IP address
ip-address show Shows the interface IP address and configuration
link-speed set Sets the interface IP link speed
ping Sends ping messages
4036-8302(config-if)# interface ethernet set ?
interface ethernet set interface ethernet set
4036-8302(config-if)# ip-address show
port selection Ethernet
ip 192.168.0.2
mask 255.255.255.0
broadcast 192.168.0.255
DHCP client enabled
Link-speed auto-negotiation
4036-8302(config-if)# exit
4036-8302(config)# exit
4036-8302# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
cable-config show Shows the cable configuration
clock show Shows the system clock
config Changes to Configuration mode
debug Change to debug mode
disable Changes to Guest mode
end Ends the CLI
exit Exits to previous menu
front show Shows the blade module information at the front of the c
hassis
health-monitor Changes to Health Monitor mode
info-led set Sets the info-led state
info-led show Shows the info-led state
logs Changes to display logs menu
module-firmware show Shows modules firmware information
password update Changes the admin or the enable password
ping Sends ping messages
reload Restarts the switch software
remote show Shows the remote client configuration
route default-gw show Shows the default gateway IP address
sm-info show Shows the SM parameters
temperature show Shows the board temperature in Celsius and Fahrenheit
update firmware chassis Updates the firmware version (embedded in the software u
pdate) using previously defined server name, user name,
and password
update software chassis Updates the software version using previously defined se
rver name, user name, and password
utilities Changes to switch debug Utilities mode
version show Shows software version information
4036-8302# update firmware chassis ?
update firmware chassis update firmware chassis [update-file-dir]
4036-8302# utilities
4036-8302(utilities)# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
end Ends the CLI
exit Exits to previous menu
ibaddr Shows the lid and GID addresses of the specified port
ibcheckerrors Scans the network to validate the connectivity
ibcheckerrs Validate IB port (or node) and report errors in counters above t
hreshold
ibchecknet Scans the network to validate the connectivity
ibcheckwidth Scans the network to validate the active link widths
ibclearcounters Clears the PMA port counters
ibclearerrors Clears the PMA error counters in PortCounters
ibhosts Extracts the CA nodes
ibnetdiscover Performs IB subnet discovery
ibportstate Queried the port state and port physical state of an IB port
ibswitches Extracts the IB switches
ibtracert Trace the path from a source GID/LID to a destination GID/LID
perfquery Obtain the PortCounters (basic performance and error counters) f
rom the PMA at the node specified
port-verify Performs a port-verify command
saquery Issue some SA queries
smpquery Allows a basic subset of standard SMP queries
vendstat Queries vendor-specific information of a switch LID
4036-8302(utilities)# exit
4036-8302# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
cable-config show Shows the cable configuration
clock show Shows the system clock
config Changes to Configuration mode
debug Change to debug mode
disable Changes to Guest mode
end Ends the CLI
exit Exits to previous menu
front show Shows the blade module information at the front of the c
hassis
health-monitor Changes to Health Monitor mode
info-led set Sets the info-led state
info-led show Shows the info-led state
logs Changes to display logs menu
module-firmware show Shows modules firmware information
password update Changes the admin or the enable password
ping Sends ping messages
reload Restarts the switch software
remote show Shows the remote client configuration
route default-gw show Shows the default gateway IP address
sm-info show Shows the SM parameters
temperature show Shows the board temperature in Celsius and Fahrenheit
update firmware chassis Updates the firmware version (embedded in the software u
pdate) using previously defined server name, user name,
and password
update software chassis Updates the software version using previously defined se
rver name, user name, and password
utilities Changes to switch debug Utilities mode
version show Shows software version information
4036-8302# update firmware chassis
=== Testing connection ==
Unable to contact remote server ftp.yourftp.com - Upgrade Failure
Unable to run command
4036-8302# update firmware chassis 192.168.0.3
=== Testing connection ==
Unable to contact remote server ftp.yourftp.com - Upgrade Failure
Unable to run command
4036-8302# sm-info show
subnet manager info is:
sweep_interval: 15
max_wire_smps: 16
lmc: 0
max_op_vls: 5
transaction_timeout: 150
head_of_queue_lifetime: 16
leaf_head_of_queue_lifetime: 16
packet_life_time: 18
sminfo_polling_timeout: 5000
polling_retry_number: 12
reassign_lids: disable
babbling_port_policy: disable
routing_engine_names: minhop
log_flags: 7
force_link_speed: 0
polling_rate: 30
mode: enable
state: master
sm_priority: 4
4036-8302# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
cable-config show Shows the cable configuration
clock show Shows the system clock
config Changes to Configuration mode
debug Change to debug mode
disable Changes to Guest mode
end Ends the CLI
exit Exits to previous menu
front show Shows the blade module information at the front of the c
hassis
health-monitor Changes to Health Monitor mode
info-led set Sets the info-led state
info-led show Shows the info-led state
logs Changes to display logs menu
module-firmware show Shows modules firmware information
password update Changes the admin or the enable password
ping Sends ping messages
reload Restarts the switch software
remote show Shows the remote client configuration
route default-gw show Shows the default gateway IP address
sm-info show Shows the SM parameters
temperature show Shows the board temperature in Celsius and Fahrenheit
update firmware chassis Updates the firmware version (embedded in the software u
pdate) using previously defined server name, user name,
and password
update software chassis Updates the software version using previously defined se
rver name, user name, and password
utilities Changes to switch debug Utilities mode
version show Shows software version information
4036-8302# remote show
remote configuration
-----------------------
remote server: ftp.yourftp.com
username: release-products
protocol: FTP
4036-8302# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
cable-config show Shows the cable configuration
clock show Shows the system clock
config Changes to Configuration mode
debug Change to debug mode
disable Changes to Guest mode
end Ends the CLI
exit Exits to previous menu
front show Shows the blade module information at the front of the c
hassis
health-monitor Changes to Health Monitor mode
info-led set Sets the info-led state
info-led show Shows the info-led state
logs Changes to display logs menu
module-firmware show Shows modules firmware information
password update Changes the admin or the enable password
ping Sends ping messages
reload Restarts the switch software
remote show Shows the remote client configuration
route default-gw show Shows the default gateway IP address
sm-info show Shows the SM parameters
temperature show Shows the board temperature in Celsius and Fahrenheit
update firmware chassis Updates the firmware version (embedded in the software u
pdate) using previously defined server name, user name,
and password
update software chassis Updates the software version using previously defined se
rver name, user name, and password
utilities Changes to switch debug Utilities mode
version show Shows software version information
4036-8302# remote ?
remote show remote show
4036-8302# remote show
remote configuration
-----------------------
remote server: ftp.yourftp.com
username: release-products
protocol: FTP
process '-/sbin
4036 Version 3.1.0 BUILD ID 718
Tue Aug 10 12:41:37 IDT 2010
4036-8302 login: admin
Password:
Welcome to Voltaire Switch 4036-8302
4036-8302# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
cable-config show Shows the cable configuration
clock show Shows the system clock
config Changes to Configuration mode
debug Change to debug mode
disable Changes to Guest mode
end Ends the CLI
exit Exits to previous menu
front show Shows the blade module information at the front of the c
hassis
health-monitor Changes to Health Monitor mode
info-led set Sets the info-led state
info-led show Shows the info-led state
logs Changes to display logs menu
module-firmware show Shows modules firmware information
password update Changes the admin or the enable password
ping Sends ping messages
reload Restarts the switch software
remote show Shows the remote client configuration
route default-gw show Shows the default gateway IP address
sm-info show Shows the SM parameters
temperature show Shows the board temperature in Celsius and Fahrenheit
update firmware chassis Updates the firmware version (embedded in the software u
pdate) using previously defined server name, user name,
and password
update software chassis Updates the software version using previously defined se
rver name, user name, and password
utilities Changes to switch debug Utilities mode
version show Shows software version information
4036-8302# bit intro
bit intro
Syntax error in the first word.
4036-8302# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
cable-config show Shows the cable configuration
clock show Shows the system clock
config Changes to Configuration mode
debug Change to debug mode
disable Changes to Guest mode
end Ends the CLI
exit Exits to previous menu
front show Shows the blade module information at the front of the c
hassis
health-monitor Changes to Health Monitor mode
info-led set Sets the info-led state
info-led show Shows the info-led state
logs Changes to display logs menu
module-firmware show Shows modules firmware information
password update Changes the admin or the enable password
ping Sends ping messages
reload Restarts the switch software
remote show Shows the remote client configuration
route default-gw show Shows the default gateway IP address
sm-info show Shows the SM parameters
temperature show Shows the board temperature in Celsius and Fahrenheit
update firmware chassis Updates the firmware version (embedded in the software u
pdate) using previously defined server name, user name,
and password
update software chassis Updates the software version using previously defined se
rver name, user name, and password
utilities Changes to switch debug Utilities mode
version show Shows software version information
4036-8302# remote show
remote configuration
-----------------------
remote server: ftp.yourftp.com
username: release-products
protocol: FTP
4036-8302# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
cable-config show Shows the cable configuration
clock show Shows the system clock
config Changes to Configuration mode
debug Change to debug mode
disable Changes to Guest mode
end Ends the CLI
exit Exits to previous menu
front show Shows the blade module information at the front of the c
hassis
health-monitor Changes to Health Monitor mode
info-led set Sets the info-led state
info-led show Shows the info-led state
logs Changes to display logs menu
module-firmware show Shows modules firmware information
password update Changes the admin or the enable password
ping Sends ping messages
reload Restarts the switch software
remote show Shows the remote client configuration
route default-gw show Shows the default gateway IP address
sm-info show Shows the SM parameters
temperature show Shows the board temperature in Celsius and Fahrenheit
update firmware chassis Updates the firmware version (embedded in the software u
pdate) using previously defined server name, user name,
and password
update software chassis Updates the software version using previously defined se
rver name, user name, and password
utilities Changes to switch debug Utilities mode
version show Shows software version information
4036-8302# config-remote
config-remote
Syntax error in the first word.
4036-8302# config remote
config remote
Syntax error after word #1.
4036-8302# config
4036-8302(config)# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
ccm Changes to ccm mode
end Ends the CLI
exit Exits to previous menu
factory-default Switches back to factory default, and reboots the system
fca Changes to FCA configuration mode
interface Changes to interface configuration mode
names Changes to names configuration mode
ntp Changes to ntp configuration mode
ping Sends ping messages
pm Changes to PM configuration mode
policy Changes to Policy mode
port Changes to port configuration mode
remote Changes to remote configuration mode
security Changes to security configuration mode
sm Changes to SM configuration mode
snmp Changes to SNMP configuration mode
4036-8302(config)# remote protocol ?
4036-8302(config)# remote protocol ftp
remote protocol ftp
Syntax error after word #1.
4036-8302(config)# remote ?
remote remote
4036-8302(config)# remote ftp
remote ftp
Syntax error after word #1.
4036-8302(config)# protocol set ftp
protocol set ftp
Syntax error in the first word.
4036-8302(config)# protocol ?
4036-8302(config)# protocol
protocol
Syntax error in the first word.
4036-8302(config)# protocol >
protocol >
Syntax error in the first word.
4036-8302(config)# protocol <
protocol <
Syntax error in the first word.
4036-8302(config)# username mellanox
username mellanox
Syntax error in the first word.
4036-8302(config)# remote username mellanox
remote username mellanox
Syntax error after word #1.
4036-8302(config)# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
ccm Changes to ccm mode
end Ends the CLI
exit Exits to previous menu
factory-default Switches back to factory default, and reboots the system
fca Changes to FCA configuration mode
interface Changes to interface configuration mode
names Changes to names configuration mode
ntp Changes to ntp configuration mode
ping Sends ping messages
pm Changes to PM configuration mode
policy Changes to Policy mode
port Changes to port configuration mode
remote Changes to remote configuration mode
security Changes to security configuration mode
sm Changes to SM configuration mode
snmp Changes to SNMP configuration mode
4036-8302(config)# remote
4036-8302(config-remote)# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
copy flash: running-config Restores the configuration from a file in the lo
cal repository path. The new values will be appl
ied on reboot
copy remote: running-config Downloads the configuration from the remote serv
er using previously defined server name, user na
me, and password. The remote path must contain t
he exported file name. The new values will be ap
plied on reboot
copy running-config flash: Saves the configuration file in the local reposi
tory path.In case of empty name the file name is
evaluated by default
copy running-config remote: Uploads the configuration to the remote server u
sing previously defined server name, user name a
nd password. The remote path can contain the imp
orted file name, if the file name is not indicat
ed, it will be created with a default name, any
characteristic after the last slash in the path
will be used as your own defined file name
end Ends the CLI
exit Exits to previous menu
exportLOGs Uploads Logs to the remote server, using previou
sly defined server name, user name, and password
--- Press <enter> to continue ---
flash delete Delete from flash specific file
flash show Shows the configuration files in flash
password Sets the user password to access remote server
protocol set Sets the protocol to access remote server
remote show Shows the remote client configuration
server Sets the remote server ip-address
username Sets the user name to access remote server
4036-8302(config-remote)# protocol set ftp
protocol set ftp
Input error: input ('ftp') is not allowed.
4036-8302(config-remote)# protocol set ?
protocol set protocol set [FTP | SCP]
4036-8302(config-remote)# protocol set FTP
4036-8302(config-remote)# remote show
remote configuration
-----------------------
remote server: ftp.yourftp.com
username: release-products
protocol: FTP
4036-8302(config-remote)# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
copy flash: running-config Restores the configuration from a file in the lo
cal repository path. The new values will be appl
ied on reboot
copy remote: running-config Downloads the configuration from the remote serv
er using previously defined server name, user na
me, and password. The remote path must contain t
he exported file name. The new values will be ap
plied on reboot
copy running-config flash: Saves the configuration file in the local reposi
tory path.In case of empty name the file name is
evaluated by default
copy running-config remote: Uploads the configuration to the remote server u
sing previously defined server name, user name a
nd password. The remote path can contain the imp
orted file name, if the file name is not indicat
ed, it will be created with a default name, any
characteristic after the last slash in the path
will be used as your own defined file name
end Ends the CLI
exit Exits to previous menu
exportLOGs Uploads Logs to the remote server, using previou
sly defined server name, user name, and password
--- Press <enter> to continue ---
flash delete Delete from flash specific file
flash show Shows the configuration files in flash
password Sets the user password to access remote server
protocol set Sets the protocol to access remote server
remote show Shows the remote client configuration
server Sets the remote server ip-address
username Sets the user name to access remote server
4036-8302(config-remote)# server 192.168.0.3
4036-8302(config-remote)# username mellanox
4036-8302(config-remote)# password
password
Syntax error after word #1.
4036-8302(config-remote)# password
password: ******
4036-8302(config-remote)# remote show
remote configuration
-----------------------
remote server: 192.168.0.3
username: mellanox
protocol: FTP
4036-8302(config-remote)# exit
4036-8302(config)# exit
4036-8302# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
cable-config show Shows the cable configuration
clock show Shows the system clock
config Changes to Configuration mode
debug Change to debug mode
disable Changes to Guest mode
end Ends the CLI
exit Exits to previous menu
front show Shows the blade module information at the front of the c
hassis
health-monitor Changes to Health Monitor mode
info-led set Sets the info-led state
info-led show Shows the info-led state
logs Changes to display logs menu
module-firmware show Shows modules firmware information
password update Changes the admin or the enable password
ping Sends ping messages
reload Restarts the switch software
remote show Shows the remote client configuration
route default-gw show Shows the default gateway IP address
sm-info show Shows the SM parameters
temperature show Shows the board temperature in Celsius and Fahrenheit
update firmware chassis Updates the firmware version (embedded in the software u
pdate) using previously defined server name, user name,
and password
update software chassis Updates the software version using previously defined se
rver name, user name, and password
utilities Changes to switch debug Utilities mode
version show Shows software version information
4036-8302# upgrade software
upgrade software
Syntax error in the first word.
4036-8302# update software
update software
Syntax error after word #2.
4036-8302# ?
'<'command> ? Displays the command usage string
? Displays the list of available commands
cable-config show Shows the cable configuration
clock show Shows the system clock
config Changes to Configuration mode
debug Change to debug mode
disable Changes to Guest mode
end Ends the CLI
exit Exits to previous menu
front show Shows the blade module information at the front of the c
hassis
health-monitor Changes to Health Monitor mode
info-led set Sets the info-led state
info-led show Shows the info-led state
logs Changes to display logs menu
module-firmware show Shows modules firmware information
password update Changes the admin or the enable password
ping Sends ping messages
reload Restarts the switch software
remote show Shows the remote client configuration
route default-gw show Shows the default gateway IP address
sm-info show Shows the SM parameters
temperature show Shows the board temperature in Celsius and Fahrenheit
update firmware chassis Updates the firmware version (embedded in the software u
pdate) using previously defined server name, user name,
and password
update software chassis Updates the software version using previously defined se
rver name, user name, and password
utilities Changes to switch debug Utilities mode
version show Shows software version information
4036-8302# remote show
remote configuration
-----------------------
remote server: 192.168.0.3
username: mellanox
protocol: FTP
4036-8302# update software chassis
=== Testing connection ==
Unable to contact remote server 192.168.0.3 - Upgrade Failure
Unable to run command
4036-8302# update firmware chassis
=== Testing connection ==
Unable to contact remote server 192.168.0.3 - Upgrade Failure
Unable to run command
4036-8302# show ip
show ip
Syntax error in the first word.
4036-8302# remote show
remote configuration
-----------------------
remote server: 192.168.0.3
username: mellanox
protocol: FTP
4036-8302# update software chassis
=== Testing connection ==
/usr/voltaire/scripts/ibswqdr-upgrade-install.sh: line 670: [: 220-FileZilla: integer expression expected
=== Test done ==
Getting files from remote FTP server....
Connecting to 192.168.0.3 (192.168.0.3:21)
wget: ftp login: Login or password incorrect!
FTP: Software file not found, bypass software upgrade - Upgrade Failure
Unable to run command
4036-8302# update software chassis
=== Testing connection ==
/usr/voltaire/scripts/ibswqdr-upgrade-install.sh: line 670: [: 220-FileZilla: integer expression expected
=== Test done ==
Getting files from remote FTP server....
Connecting to 192.168.0.3 (192.168.0.3:21)
wget: bad response to RETR: 550 File not found
FTP: Software file not found, bypass software upgrade - Upgrade Failure
Unable to run command
4036-8302# update software chassis
=== Testing connection ==
/usr/voltaire/scripts/ibswqdr-upgrade-install.sh: line 670: [: 220-FileZilla: integer expression expected
=== Test done ==
Getting files from remote FTP server....
Connecting to 192.168.0.3 (192.168.0.3:21)
upgrade_all.tgz 100% |*******************************| 102M 00:00:00 ETA
Checking MD5 of the image
MD5 check passed ..........
Installing kernel image ...
Erasing blocks: 11/11 (100%)
Writing data: 1373k/1373k (100%)
Verifying data: 1373k/1373k (100%)
Installing FDT file ...
Erasing blocks: 1/1 (100%)
Writing data: 11k/11k (100%)
Verifying data: 11k/11k (100%)
Installing ramdisk image ...
Erasing blocks: 175/175 (100%)
Writing data: 22330k/22330k (100%)
Verifying data: 22330k/22330k (100%)
Installing safe kernel image ...
Erasing blocks: 11/11 (100%)
Writing data: 1373k/1373k (100%)
Verifying data: 1373k/1373k (100%)
Installing safe FDT file ...
Erasing blocks: 1/1 (100%)
Writing data: 11k/11k (100%)
Verifying data: 11k/11k (100%)
Installing safe ramdisk image ...
Erasing blocks: 175/175 (100%)
Writing data: 22330k/22330k (100%)
Verifying data: 22330k/22330k (100%)
Updating u-boot
Erasing blocks: 3/3 (100%)
Writing data: 384k/384k (100%)
Verifying data: 384k/384k (100%)
Set u-boot env to default
Erasing 128 Kibyte @ 20000 -- 50 % complete.
Burning the FW image
-W- Unknown device id (23130) in the given FW image. Skipping HW match check.
Current FW version on flash: 7.3.100
New FW version: 7.4.2070
You are about to replace current PSID on flash - "VLT1210031300" with a different PSID - "VLT1210032000".
Note: It is highly recommended not to change the PSID.
Do you want to continue ? (y/n) [n] : y
Burning first FW image without signatures - OK
Restoring first signature - OK
Finished. Change will be effective only after next reboot
System will be rebooted to complete upgrade process
starting pid 5232, tty '': '/etc/rc.d/rcS stop'
4036-8302# ibsw-init.sh stop...
Thu Jun 27 14:14:09 BST 2019
repsave: total entries to dump 16
625%
repsave: total execution count = 1 sec.
WRITE Returned retError = 0
Returned retError = 0
nvigor.sh stop...
Thu Jun 27 14:14:10 BST 2019
/usr/voltaire/a == stop send to VIP,VSM,MNG : waiting for 1 sec. ==
All stopped... Removing nvigor.sh lock
Stopping crond:
Stopping inetd:
Syncing hardware clock to system time
0xc3
U-Boot 1.3.4.32 (Feb 6 2011 - 10:18:30)
CPU: AMCC PowerPC 460EX Rev. A at 666.666 MHz (PLB=166, OPB=83, EBC=83 MHz)
Security/Kasumi support
Bootstrap Option E - Boot ROM Location EBC (16 bits)
Internal PCI arbiter disabled
32 kB I-Cache 32 kB D-Cache
Board: 4036QDR - Voltaire 4036 QDR Switch Board
I2C: ready
DRAM: 512 MB (ECC enabled, 333 MHz, CL3)
FLASH: 64 MB
NAND: 256 MiB
*** Warning - bad CRC, using default environment
MAC Address:
PCIE1: successfully set as root-complex
PCIE: Bus Dev VenId DevId Class Int
01 00 15b3 bd34 0c06 00
Net: ppc_4xx_eth0
Type run flash_nfs to mount root filesystem over NFS
Hit any key to stop autoboot: 0
Booting secondary, Press ^C to abort
## Booting kernel from Legacy Image at fc000000 ...
Image Name: Linux-2.6.26
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1406000 Bytes = 1.3 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Flattened Device Tree blob at fc1e0000
Booting using the fdt blob at 0xfc1e0000
Loading Device Tree to 007fa000, end 007ffde4 ... OK
Using Voltaire machine description
Linux version 2.6.26 (odeds@heka.lab.mtl.com) (gcc version 4.2.2) #22 Tue Jun 7 11:13:48 IDT 2011
Zone PFN ranges:
DMA 0 -> 131072
Normal 131072 -> 131072
HighMem 131072 -> 131072
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 131072
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
Kernel command line: root=/dev/mtdblock2 load_ramdisk=1 prompt_ramdisk=0 prim_flg=0 ip=::::voltaire4036:eth0:off panic=1 console=ttyS0,38400
UIC0 (32 IRQ sources) at DCR 0xc0
UIC1 (32 IRQ sources) at DCR 0xd0
UIC2 (32 IRQ sources) at DCR 0xe0
UIC3 (32 IRQ sources) at DCR 0xf0
PID hash table entries: 2048 (order: 11, 8192 bytes)
clocksource: timebase mult[600000] shift[22] registered
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 516352k/524288k available (2828k kernel code, 7600k reserved, 108k data, 111k bss, 172k init)
SLUB: Genslabs=10, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Mount-cache hash table entries: 512
net_namespace: 340 bytes
NET: Registered protocol family 16
256k L2-cache enabled
PCIE1: Checking link...
PCIE1: Device detected, waiting for link...
PCIE1: link is up !
PCI host bridge /plb/pciex@d20000000 (primary) ranges:
MEM 0x0000000e80000000..0x0000000effffffff -> 0x0000000080000000
IO 0x0000000f80010000..0x0000000f8001ffff -> 0x0000000000000000
4xx PCI DMA offset set to 0x00000000
PCIE1: successfully set as root-complex
PCI: Probing PCI hardware
PCI: Hiding 4xx host bridge resources 0000:80:00.0
PCI: Bridge: 0000:80:00.0
IO window: disabled.
MEM window: 0x80000000-0x800fffff
PREFETCH window: disabled.
NET: Registered protocol family 2
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
NET: Registered protocol family 1
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 1009
io scheduler noop registered (default)
Serial: 8250/16550 driver $Revision: 1.3 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x4ef600300 (irq = 19) is a 16550A
console [ttyS0] enabled
serial8250.0: ttyS1 at MMIO 0x4ef600400 (irq = 20) is a 16550A
serial8250.0: ttyS2 at MMIO 0x4ef600500 (irq = 29) is a 16550A
serial8250.0: ttyS3 at MMIO 0x4ef600600 (irq = 21) is a 16550A
4ef600300.serial: ttyS0 at MMIO 0x4ef600300 (irq = 19) is a 16550A
4ef600400.serial: ttyS1 at MMIO 0x4ef600400 (irq = 20) is a 16550A
4ef600500.serial: ttyS2 at MMIO 0x4ef600500 (irq = 29) is a 16550A
4ef600600.serial: ttyS3 at MMIO 0x4ef600600 (irq = 21) is a 16550A
brd: module loaded
loop: module loaded
PPC 4xx OCP EMAC driver, version 3.54
MAL v2 /plb/mcmal, 2 TX channels, 16 RX channels
ZMII /plb/opb/emac-zmii@ef600d00 initialized
RGMII /plb/opb/emac-rgmii@ef601500 initialized with MDIO support
TAH /plb/opb/emac-tah@ef601350 initialized
TAH /plb/opb/emac-tah@ef601450 initialized
/plb/opb/emac-rgmii@ef601500: input 0 in RGMII mode
PHY address 0xffffffff map 0x0
eth0: EMAC-0 /plb/opb/ethernet@ef600e00, MAC 00:08:f1:10:83:02
eth0: found Generic MII PHY (0x00)
/plb/opb/emac-rgmii@ef601500: input 1 in RGMII mode
PHY address 0xffffffff map 0x1
/plb/opb/ethernet@ef600f00: can't find PHY!
4cc000000.nor_flash: Found 1 x16 devices at 0x0 in 16-bit bank
4cc000000.nor_flash: Found 1 x16 devices at 0x2000000 in 16-bit bank
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Using buffer write method
Using auto-unlock on power-up/resume
cfi_cmdset_0001: Erase suspend on write enabled
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Creating 9 MTD partitions on "4cc000000.nor_flash":
0x00000000-0x001e0000 : "kernel"
0x001e0000-0x00200000 : "dtb"
0x00200000-0x01dc0000 : "ramdisk"
0x01dc0000-0x01fa0000 : "safe-kernel"
0x01fa0000-0x01fc0000 : "safe-dtb"
0x01fc0000-0x03b80000 : "safe-ramdisk"
0x03b80000-0x03f60000 : "config"
0x03f60000-0x03fa0000 : "u-boot env"
0x03fa0000-0x04000000 : "u-boot"
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 310 at 0x026c0000
Bad eraseblock 1334 at 0x0a6c0000
Bad eraseblock 1474 at 0x0b840000
Creating 1 MTD partitions on "4e0000000.ndfc.nand":
0x00000000-0x10000000 : "log"
i2c /dev entries driver
IBM IIC driver v2.1
ibm-iic(/plb/opb/i2c@ef600700): using standard (100 kHz) mode
ibm-iic(/plb/opb/i2c@ef600800): using standard (100 kHz) mode
i2c-2: Virtual I2C bus (Physical bus i2c-0, multiplexer 0x70 port 0)
i2c-3: Virtual I2C bus (Physical bus i2c-0, multiplexer 0x70 port 1)
i2c-4: Virtual I2C bus (Physical bus i2c-0, multiplexer 0x70 port 2)
i2c-5: Virtual I2C bus (Physical bus i2c-0, multiplexer 0x70 port 3)
rtc-ds1307 6-0068: rtc core: registered ds1338 as rtc0
rtc-ds1307 6-0068: 56 bytes nvram
i2c-6: Virtual I2C bus (Physical bus i2c-0, multiplexer 0x70 port 4)
i2c-7: Virtual I2C bus (Physical bus i2c-0, multiplexer 0x70 port 5)
i2c-8: Virtual I2C bus (Physical bus i2c-0, multiplexer 0x70 port 6)
i2c-9: Virtual I2C bus (Physical bus i2c-0, multiplexer 0x70 port 7)
pca954x 0-0070: registered 8 virtual busses for I2C switch pca9548
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
ip6tnl0: Disabled Privacy Extensions
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc-ds1307 6-0068: setting system clock to 2019-06-27 13:14:39 UTC (1561641279)
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 172k init
init started: BusyBox v1.12.2 (2011-01-03 14:13:22 IST)
starting pid 15, tty '': '/etc/rc.d/rcS'
mount: no /proc/mounts
Mounting /proc and /sys
Mounting filesysEXT2-fs warning: checktime reached, running e2fsck is recommended
tems
Loading module Voltaire
Starting crond:
Starting telnetd:
ibsw-init.sh start...
Thu Jun 27 13:15:12 UTC 2019
INSTALL FLAG 0x2
Returned retError = 0
Upgrading repository ...
100%
repload: create #SQL done.
100%
repload: raw data inserted.
100%
repload: create #TRG done.
repload: total execution count = 2 sec.
Returned retError = 0
100%
repmerge: total execution count = 1 sec.
repsave: total entries to dump 19
526%
repsave: total execution count = 1 sec.
WRITE Returned retError = 0
Returned retError = 0
Upgrading repository done in 7 sec.
Software upgrade completed
starting syslogd & klogd ...
Starting ISR: ib_is4 0000:81:00.0: ep0_dev_name 0000:81:00.0
starting pid 876, tty '': '-/sb
4036 Version 3.6.0 BUILD ID 857
Tue Jun 7 11:22:29 IDT 2011
4036-8302 login: admin
Password:
Welcome to Voltaire Switch 4036-8302
4036-8302# ?
<'command'> ? Displays the command usage string
? Displays the list of available commands
cable-config show Shows the cable configuration
clock show Shows the system clock
config Changes to Configuration mode
debug Change to debug mode
disable Changes to Guest mode
end Ends the CLI
exit Exits to previous menu
front show Shows the blade module information at the front of the c
hassis
health-monitor Changes to Health Monitor mode
info-led set Sets the info-led state
info-led show Shows the info-led state
logs Changes to display logs menu
module-firmware show Shows modules firmware information
password update Changes the admin or the enable password
ping Sends ping messages
reload Restarts the switch software
remote show Shows the remote client configuration
route default-gw show Shows the default gateway IP address
sm-info show Shows the SM parameters
temperature show Shows the board temperature in Celsius and Fahrenheit
update firmware chassis Updates the firmware version (embedded in the software u
pdate) using previously defined server name, user name,
and password
update software chassis Updates the software version using previously defined se
rver name, user name, and password
utilities Changes to switch debug Utilities mode
version show Shows software version information
4036-8302# config
4036-8302(config)# ?
<'command'> ? Displays the command usage string
? Displays the list of available commands
ccm Changes to ccm mode
end Ends the CLI
exit Exits to previous menu
factory-default Switches back to factory default, and reboots the system
fca Changes to FCA configuration mode
interface Changes to interface configuration mode
names Changes to names configuration mode
ntp Changes to ntp configuration mode
ping Sends ping messages
pm Changes to PM configuration mode
policy Changes to Policy mode
port Changes to port configuration mode
remote Changes to remote configuration mode
security Changes to security configuration mode
sm Changes to SM configuration mode
snmp Changes to SNMP configuration mode
4036-8302(config)# remote
4036-8302(config-remote)# ?
<'command'> ? Displays the command usage string
? Displays the list of available commands
copy flash: running-config Restores the configuration from a file in the lo
cal repository path. The new values will be appl
ied on reboot
copy remote: running-config Downloads the configuration from the remote serv
er using previously defined server name, user na
me, and password. The remote path must contain t
he exported file name. The new values will be ap
plied on reboot
copy running-config flash: Saves the configuration file in the local reposi
tory path.In case of empty name the file name is
evaluated by default
copy running-config remote: Uploads the configuration to the remote server u
sing previously defined server name, user name a
nd password. The remote path can contain the imp
orted file name, if the file name is not indicat
ed, it will be created with a default name, any
characteristic after the last slash in the path
will be used as your own defined file name
end Ends the CLI
exit Exits to previous menu
exportLOGs Uploads Logs to the remote server, using previou
sly defined server name, user name, and password
--- Press <enter> to continue ---
flash delete Delete from flash specific file
flash show Shows the configuration files in flash
password Sets the user password to access remote server
protocol set Sets the protocol to access remote server
remote show Shows the remote client configuration
server Sets the remote server ip-address
username Sets the user name to access remote server
4036-8302(config-remote)# remote show
remote configuration
-----------------------
remote server: 192.168.0.3
username: mellanox
protocol: FTP
4036-8302(config-remote)# exit
4036-8302(config)# exit
4036-8302# ?
<'command'> ? Displays the command usage string
? Displays the list of available commands
cable-config show Shows the cable configuration
clock show Shows the system clock
config Changes to Configuration mode
debug Change to debug mode
disable Changes to Guest mode
end Ends the CLI
exit Exits to previous menu
front show Shows the blade module information at the front of the c
hassis
health-monitor Changes to Health Monitor mode
info-led set Sets the info-led state
info-led show Shows the info-led state
logs Changes to display logs menu
module-firmware show Shows modules firmware information
password update Changes the admin or the enable password
ping Sends ping messages
reload Restarts the switch software
remote show Shows the remote client configuration
route default-gw show Shows the default gateway IP address
sm-info show Shows the SM parameters
temperature show Shows the board temperature in Celsius and Fahrenheit
update firmware chassis Updates the firmware version (embedded in the software u
pdate) using previously defined server name, user name,
and password
update software chassis Updates the software version using previously defined se
rver name, user name, and password
utilities Changes to switch debug Utilities mode
version show Shows software version information
4036-8302# update firmware chassis
Getting files from remote FTP server....
No such file `firmware.tar'.
FTP: Software file not found, bypass software upgrade - Upgrade Failure
Unable to run command
4036-8302# update software chassis
Getting files from remote FTP server....
2019-06-27 14:26:28 URL: ftp://mellanox:*password*@192.168.0.3/upgrade_all.tgz [108611864] -> "upgrade_all.tgz" [1]
Checking MD5 of the image
MD5 check passed ..........
pre_upgrade: it's an old version, need to upgrade
pre_upgrade: Erasing /dev/mtd0...
Erasing 128 Kibyte @ 1c0000 -- 93 % complete.
pre_upgrade: Installing kernel image at offset 0 in mtdblock0...
Erasing blocks: 11/11 (100%)
Writing data: 1373k/1373k (100%)
Verifying data: 1373k/1373k (100%)
pre_upgrade: Erasing /dev/mtd1...
Erasing 128 Kibyte @ 0 -- 0 % complete.
pre_upgrade: Installing DTB file at offset 0 in mtdblock1...
Erasing blocks: 1/1 (100%)
Writing data: 11k/11k (100%)
Verifying data: 11k/11k (100%)
pre_upgrade: Erasing /dev/mtd2...
Erasing 128 Kibyte @ 1ba0000 -- 99 % complete.
pre_upgrade: Installing safe kernel image at offset 0 in mtdblock2...
1373+1 records in
1373+1 records out
pre_upgrade: Installing ramdisk B image at offset 2304 in mtdblock2...
6757+1 records in
6757+1 records out
pre_upgrade: Updating u-boot (0) at offset 13952 in mtdblock2...
384+0 records in
384+0 records out
pre_upgrade: Installing ramdisk A image (first 14080K) at offset 14336 in mtdblock2...
14080+0 records in
14080+0 records out
pre_upgrade: Erasing /dev/mtd3...
Erasing 128 Kibyte @ 1c0000 -- 93 % complete.
pre_upgrade: Installing ramdisk A image (second part) at offset 0 in mtdblock3...(mtdblock2_offset =28416)
1920+0 records in
1920+0 records out
pre_upgrade: Erasing /dev/mtd4...
Erasing 128 Kibyte @ 0 -- 0 % complete.
pre_upgrade: Updating u-boot (1) (first 128K) at offset 0 in mtdblock4...
128+0 records in
128+0 records out
pre_upgrade: Erasing /dev/mtd5...
Erasing 128 Kibyte @ 1ba0000 -- 99 % complete.
pre_upgrade: Updating u-boot (1) (second part) at offset 0 in mtdblock5...
256+0 records in
256+0 records out
pre_upgrade: Installing safe ramdisk A image at offset 256 in mtdblock5...
16000+0 records in
16000+0 records out
pre_upgrade: Updating u-boot (2) at offset 16256 in mtdblock5...
384+0 records in
384+0 records out
pre_upgrade: Installing safe ramdisk B image at offset 16640 in mtdblock5...
6757+1 records in
6757+1 records out
pre_upgrade: Installing safe DTB file at offset 28288 in mtdblock5...
11+1 records in
11+1 records out
pre_upgrade: Updating u-boot at mtd8
Erasing blocks: 3/3 (100%)
Writing data: 384k/384k (100%)
Verifying data: 384k/384k (100%)
pre_upgrade: Set u-boot env to default (mtd7)
Erasing 128 Kibyte @ 20000 -- 50 % complete.
Burning the FW image
-W- Unknown device id (23130) in the given FW image. Skipping HW match check.
Current FW version on flash: 7.4.2070
New FW version: 7.4.2200
You are about to replace current PSID on flash - "VLT1210032000" with a different PSID - "VLT1210032201".
Note: It is highly recommended not to change the PSID.
Do you want to continue ? (y/n) [n] : y
Burning second FW image without signatures - OK
Restoring second signature - OK
Finished. Change will be effective only after next reboot
pre_upgrade: rebooting after writing images
Update_software_pre_upgrade: "Succeeded."
Update_software_pre_upgrade: "Rebooting the switch."
repsave: total entries to dump 19
526%
repsave: total execution count = 2 sec.
WRITE Returned retError = 0
Returned retError = 0
Activating HW reset!
U-Boot 1.3.4.32_4U_03 (Sep 10 2012 - 19:28:47)
CPU: AMCC PowerPC 460EX Rev. A at 666.666 MHz (PLB=166, OPB=83, EBC=83 MHz)
Security/Kasumi support
Bootstrap Option E - Boot ROM Location EBC (16 bits)
Internal PCI arbiter disabled
32 kB I-Cache 32 kB D-Cache
Board: 4036QDR - Voltaire 4036 QDR Switch Board
I2C: ready
DRAM: 512 MB (ECC enabled, 333 MHz, CL3)
FLASH: 64 MB
NAND: 256 MiB
*** Warning - bad CRC, using default environment
MAC Address:
PCIE1: successfully set as root-complex
PCIE: Bus Dev VenId DevId Class Int
01 00 15b3 bd34 0c06 00
Net: ppc_4xx_eth0
Recovery counter: 9
Type run flash_nfs to mount root filesystem over NFS
Hit any key to stop autoboot: 0
Booting secondary, Press ^C to abort
## Booting kernel from Legacy Image at fc000000 ...
Image Name: Linux-2.6.26
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1406018 Bytes = 1.3 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Flattened Device Tree blob at fc1e0000
Booting using the fdt blob at 0xfc1e0000
## Loading init Ramdisk from Legacy Image at 02000000 ...
Image Name: Voltaire QDR ramdisk
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 23303620 Bytes = 22.2 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Device Tree to 007fa000, end 007fffa0 ... OK
Loading Ramdisk to 1e85d000, end 1fe965c4 ... OK
Using Voltaire machine description
Linux version 2.6.26 (alexne@heka.lab.mtl.com) (gcc version 4.2.2) #22 Sun Sep 23 11:59:23 IST 2012
Found initrd at 0xde85d000:0xdfe965c4
Zone PFN ranges:
DMA 0 -> 131072
Normal 131072 -> 131072
HighMem 131072 -> 131072
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 131072
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
Kernel command line: root=/dev/ram ramdisk_size=0x1b00000 prim_flg=0 ip=::::voltaire4036:eth0:off panic=1 console=ttyS0,38400n8
UIC0 (32 IRQ sources) at DCR 0xc0
UIC1 (32 IRQ sources) at DCR 0xd0
UIC2 (32 IRQ sources) at DCR 0xe0
UIC3 (32 IRQ sources) at DCR 0xf0
PID hash table entries: 2048 (order: 11, 8192 bytes)
clocksource: timebase mult[600000] shift[22] registered
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 493440k/524288k available (2828k kernel code, 30364k reserved, 108k data, 111k bss, 172k init)
SLUB: Genslabs=10, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Mount-cache hash table entries: 512
net_namespace: 340 bytes
NET: Registered protocol family 16
256k L2-cache enabled
PCIE1: Checking link...
PCIE1: Device detected, waiting for link...
PCIE1: link is up !
PCI host bridge /plb/pciex@d20000000 (primary) ranges:
MEM 0x0000000e80000000..0x0000000effffffff -> 0x0000000080000000
IO 0x0000000f80010000..0x0000000f8001ffff -> 0x0000000000000000
4xx PCI DMA offset set to 0x00000000
PCIE1: successfully set as root-complex
PCI: Probing PCI hardware
PCI: Hiding 4xx host bridge resources 0000:80:00.0
PCI: Bridge: 0000:80:00.0
IO window: disabled.
MEM window: 0x80000000-0x800fffff
PREFETCH window: disabled.
NET: Registered protocol family 2
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 22757k freed
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 1009
io scheduler noop registered (default)
Serial: 8250/16550 driver $Revision: 1.3 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x4ef600300 (irq = 19) is a 16550A
console [ttyS0] enabled
serial8250.0: ttyS1 at MMIO 0x4ef600400 (irq = 20) is a 16550A
serial8250.0: ttyS2 at MMIO 0x4ef600500 (irq = 29) is a 16550A
serial8250.0: ttyS3 at MMIO 0x4ef600600 (irq = 21) is a 16550A
4ef600300.serial: ttyS0 at MMIO 0x4ef600300 (irq = 19) is a 16550A
4ef600400.serial: ttyS1 at MMIO 0x4ef600400 (irq = 20) is a 16550A
4ef600500.serial: ttyS2 at MMIO 0x4ef600500 (irq = 29) is a 16550A
4ef600600.serial: ttyS3 at MMIO 0x4ef600600 (irq = 21) is a 16550A
brd: module loaded
loop: module loaded
PPC 4xx OCP EMAC driver, version 3.54
MAL v2 /plb/mcmal, 2 TX channels, 16 RX channels
ZMII /plb/opb/emac-zmii@ef600d00 initialized
RGMII /plb/opb/emac-rgmii@ef601500 initialized with MDIO support
TAH /plb/opb/emac-tah@ef601350 initialized
TAH /plb/opb/emac-tah@ef601450 initialized
/plb/opb/emac-rgmii@ef601500: input 0 in RGMII mode
PHY address 0xffffffff map 0x0
eth0: EMAC-0 /plb/opb/ethernet@ef600e00, MAC 00:08:f1:10:83:02
eth0: found Generic MII PHY (0x00)
/plb/opb/emac-rgmii@ef601500: input 1 in RGMII mode
PHY address 0xffffffff map 0x1
/plb/opb/ethernet@ef600f00: can't find PHY!
4cc000000.nor_flash: Found 1 x16 devices at 0x0 in 16-bit bank
4cc000000.nor_flash: Found 1 x16 devices at 0x2000000 in 16-bit bank
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Using buffer write method
Using auto-unlock on power-up/resume
cfi_cmdset_0001: Erase suspend on write enabled
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Creating 15 MTD partitions on "4cc000000.nor_flash":
0x00000000-0x001e0000 : "kernel"
0x001e0000-0x00200000 : "dtb"
0x00200000-0x003e0000 : "safe-kernel"
0x003e0000-0x00440000 : "free space 1"
0x00440000-0x00fa0000 : "ramdisk-b"
0x00fa0000-0x01000000 : "u-boot 0"
0x01000000-0x01fa0000 : "ramdisk-a"
0x01fa0000-0x02000000 : "u-boot 1"
0x02000000-0x02fa0000 : "safe-ramdisk-a"
0x02fa0000-0x03000000 : "u-boot 2"
0x03000000-0x03b60000 : "safe-ramdisk-b"
0x03b60000-0x03b80000 : "safe-dtb"
0x03b80000-0x03f60000 : "config"
0x03f60000-0x03fa0000 : "u-boot env"
0x03fa0000-0x04000000 : "u-boot"
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 310 at 0x026c0000
Bad eraseblock 1334 at 0x0a6c0000
Bad eraseblock 1474 at 0x0b840000
Creating 1 MTD partitions on "4e0000000.ndfc.nand":
0x00000000-0x10000000 : "log"
i2c /dev entries driver
IBM IIC driver v2.1
ibm-iic(/plb/opb/i2c@ef600700): using standard (100 kHz) mode
ibm-iic(/plb/opb/i2c@ef600800): using standard (100 kHz) mode
i2c-2: Virtual I2C bus (Physical bus i2c-0, multiplexer 0x70 port 0)
i2c-3: Virtual I2C bus (Physical bus i2c-0, multiplexer 0x70 port 1)
i2c-4: Virtual I2C bus (Physical bus i2c-0, multiplexer 0x70 port 2)
i2c-5: Virtual I2C bus (Physical bus i2c-0, multiplexer 0x70 port 3)
rtc-ds1307 6-0068: rtc core: registered ds1338 as rtc0
rtc-ds1307 6-0068: 56 bytes nvram
i2c-6: Virtual I2C bus (Physical bus i2c-0, multiplexer 0x70 port 4)
i2c-7: Virtual I2C bus (Physical bus i2c-0, multiplexer 0x70 port 5)
i2c-8: Virtual I2C bus (Physical bus i2c-0, multiplexer 0x70 port 6)
i2c-9: Virtual I2C bus (Physical bus i2c-0, multiplexer 0x70 port 7)
pca954x 0-0070: registered 8 virtual busses for I2C switch pca9548
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
ip6tnl0: Disabled Privacy Extensions
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc-ds1307 6-0068: setting system clock to 2019-06-27 13:50:43 UTC (1561643443)
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 172k init
init started: BusyBox v1.12.2 (2011-01-03 14:13:22 IST)
starting pid 16, tty '': '/etc/rc.d/rcS'
mount: no /proc/mounts
Mounting /proc and /sys
Mounting filesysEXT2-fs warning: checktime reached, running e2fsck is recommended
tems
Loading module Voltaire
jffs2_scan_inode_node(): CRC failed on node at 0x0a187fe0: Read 0xffffffff, calculated 0x55c40651
Starting crond:
Starting telnetd:
ibsw-init.sh start...
Thu Jun 27 13:50:53 UTC 2019
INSTALL FLAG 0x2
Returned retError = 0
Upgrading repository ...
100%
repload: create #SQL done.
100%
repload: raw data inserted.
100%
repload: create #TRG done.
repload: total execution count = 2 sec.
Returned retError = 0
100%
repmerge: total execution count = 2 sec.
repsave: total entries to dump 19
526%
repsave: total execution count = 2 sec.
WRITE Returned retError = 0
Returned retError = 0
Upgrading repository done in 8 sec.
Software upgrade completed
starting syslogd & klogd ...
Starting ISR: ib_is4 0000:81:00.0: ep0_dev_name 0000:81:00.0
starting pid 878, tty '': '-/sb
4036 Version 3.9.1 BUILD ID 985
Sun Sep 23 18:01:19 IST 2012
4036-8302 login: admin
Password:
Welcome to Voltaire Switch 4036-8302
4036-8302# ?
<'command'> ? Displays the command usage string
? Displays the list of available commands
cable-config show Shows the cable configuration
clock show Shows the system clock
config Changes to Configuration mode
debug Change to debug mode
disable Changes to Guest mode
end Ends the CLI
exit Exits to previous menu
front show Shows the blade module information at the front of the c
hassis
health-monitor Changes to Health Monitor mode
info-led set Sets the info-led state
info-led show Shows the info-led state
logs Changes to display logs menu
module-firmware show Shows modules firmware information
password update Changes the admin or the enable password
ping Sends ping messages
reload Restarts the switch software
remote show Shows the remote client configuration
route default-gw show Shows the default gateway IP address
sm-info show Shows the SM parameters
temperature show Shows the board temperature in Celsius and Fahrenheit
update firmware chassis Updates the firmware version (embedded in the software u
pdate) using previously defined server name, user name,
and password
update software chassis Updates the software version using previously defined se
rver name, user name, and password
utilities Changes to switch debug Utilities mode
version show Shows software version information
4036-8302# version show
version: 3.9.1
date: Sep 23 2012 12:11:59 PM
build Id:985
4036-8302# utilities
4036-8302(utilities)# ?
<'command'> ? Displays the command usage string
? Displays the list of available commands
end Ends the CLI
exit Exits to previous menu
ibaddr Shows the lid and GID addresses of the specified port
ibcheckerrs Validate IB port (or node) and report errors in counters above t
hreshold
ibchecknet Scans the network to validate the connectivity
ibcheckwidth Scans the network to validate the active link widths
ibclearcounters Clears the PMA port counters
ibclearerrors Clears the PMA error counters in PortCounters
ibhosts Extracts the CA nodes
ibnetdiscover Performs IB subnet discovery
ibportstate Queried the port state and port physical state of an IB port
ibswitches Extracts the IB switches
ibtracert Trace the path from a source GID/LID to a destination GID/LID
perfquery Obtain the PortCounters (basic performance and error counters) f
rom the PMA at the node specified
port-verify Performs a port-verify command
saquery Issue some SA queries
smpquery Allows a basic subset of standard SMP queries
vendstat Queries vendor-specific information of a switch LID
4036-8302(utilities)# exit
4036-8302# config
4036-8302(config)# ?
<'command'> ? Displays the command usage string
? Displays the list of available commands
ccm Changes to ccm mode
end Ends the CLI
exit Exits to previous menu
factory-default Switches back to factory default, and reboots the system
fca Changes to FCA configuration mode
interface Changes to interface configuration mode
names Changes to names configuration mode
ntp Changes to ntp configuration mode
ping Sends ping messages
pm Changes to PM configuration mode
policy Changes to Policy mode
port Changes to port configuration mode
remote Changes to remote configuration mode
security Changes to security configuration mode
sm Changes to SM configuration mode
snmp Changes to SNMP configuration mode
4036-8302(config)# exit
4036-8302# ?
<'command'> ? Displays the command usage string
? Displays the list of available commands
cable-config show Shows the cable configuration
clock show Shows the system clock
config Changes to Configuration mode
debug Change to debug mode
disable Changes to Guest mode
end Ends the CLI
exit Exits to previous menu
front show Shows the blade module information at the front of the c
hassis
health-monitor Changes to Health Monitor mode
info-led set Sets the info-led state
info-led show Shows the info-led state
logs Changes to display logs menu
module-firmware show Shows modules firmware information
password update Changes the admin or the enable password
ping Sends ping messages
reload Restarts the switch software
remote show Shows the remote client configuration
route default-gw show Shows the default gateway IP address
sm-info show Shows the SM parameters
temperature show Shows the board temperature in Celsius and Fahrenheit
update firmware chassis Updates the firmware version (embedded in the software u
pdate) using previously defined server name, user name,
and password
update software chassis Updates the software version using previously defined se
rver name, user name, and password
utilities Changes to switch debug Utilities mode
version show Shows software version information
4036-8302# module-firmware show
Module No. Type Node GUID LID FW Version SW Version
---------- ---- --------- --- ---------- ----------
4036/2036 3.9.1-985
---------
CPLD 1 0x9
IS4 1 0x0008f10500108302 1 7.4.2200 VLT1210032201
---------
4036-8302#