Hi guys,
i have noticed that few members of sth have same series HBA as i do.
I have bought 2 cards and i have tried one so far.
Updated to latest firmware.
Drives 1tb wd blue and crucial BX 240g for test. Cables cbl-sast-0631 (sff to 4x sata)
Computer dell T320 fitted in x16 slot.
NVME for test is shipped (waiting) and cable will be cbl-sast-0957
output of show all
[root@localhost ~]# /opt/MegaRAID/storcli/storcli64 /c0 show all
CLI Version = 007.1504.0000.0000 June 22, 2020
Operating system = Linux 3.10.0-1127.el7.x86_64
Controller = 0
Status = Success
Description = None
Basics :
======
Controller = 0
Adapter Type = SAS3616(B0)
Model = HBA 9405W-16i
Serial Number = SP94572070
Current System Date/time = 09/29/2020 17:04:59
Concurrent commands supported = 6656
SAS Address = 500605b00fba45e0
PCI Address = 00:0a:00:00
Mfg Date = 00/00/00
Rework Date = 00/00/00
Revision No = N/A
Version :
=======
Firmware Package Build = 16.00.00.00
Firmware Version = 16.00.00.00
Bios Version = 09.09.00.00_16.00.00.00
NVDATA Version = 15.12.00.15
PSOC Version = 05689001
Driver Name = mpt3sas
Driver Version = 31.100.01.00
PCI Version :
===========
Vendor Id = 0x1000
Device Id = 0xD1
SubVendor Id = 0x1000
SubDevice Id = 0x3090
Host Interface = PCIE
Device Interface = SAS-12G
Bus Number = 10
Device Number = 0
Function Number = 0
Domain ID = 0
Pending Images in Flash :
=======================
Image name = No pending images
Status :
======
Controller Status = OK
Memory Correctable Errors = 0
Memory Uncorrectable Errors = 0
Bios was not detected during boot = No
Controller has booted into safe mode = No
Controller has booted into certificate provision mode = No
Supported Adapter Operations :
============================
Alarm Control = No
Cluster Support = No
Self Diagnostic = No
Deny SCSI Passthrough = No
Deny SMP Passthrough = No
Deny STP Passthrough = No
Support more than 8 Phys = Yes
FW and Event Time in GMT = No
Support Enclosure Enumeration = Yes
Support Allowed Operations = Yes
Support Multipath = Yes
Support Security = No
Support Config Page Model = No
Support the OCE without adding drives = No
support EKM = No
Snapshot Enabled = No
Support PFK = No
Support PI = No
Support Shield State = No
Support Set Link Speed = No
Support JBOD = No
Disable Online PFK Change = No
Real Time Scheduler = No
Support Reset Now = No
Support Emulated Drives = No
Support Secure Boot = No
Support Platform Security = No
HwCfg :
=====
ChipRevision = B0
BatteryFRU = N/A
Front End Port Count = 1
Backend Port Count = 21
Serial Debugger = Absent
NVRAM Size = 0KB
Flash Size = 16MB
On Board Memory Size = 0MB
On Board Expander = Absent
Temperature Sensor for ROC = Present
Temperature Sensor for Controller = Absent
Current Size of CacheCade (GB) = 0
Current Size of FW Cache (MB) = 0
ROC temperature(Degree Celcius) = 51
Policies :
========
Policies Table :
==============
------------------------------------------------
Policy Current Default
------------------------------------------------
Predictive Fail Poll Interval 0 sec
Interrupt Throttle Active Count 0
Interrupt Throttle Completion 0 us
Rebuild Rate 0 % 30%
PR Rate 0 % 30%
BGI Rate 0 % 30%
Check Consistency Rate 0 % 30%
Reconstruction Rate 0 % 30%
Cache Flush Interval 0s
------------------------------------------------
Flush Time(Default) = 4s
Drive Coercion Mode = none
Auto Rebuild = Off
Battery Warning = Off
ECC Bucket Size = 0
ECC Bucket Leak Rate (hrs) = 0
Restore HotSpare on Insertion = Off
Expose Enclosure Devices = Off
Maintain PD Fail History = Off
Reorder Host Requests = On
Auto detect BackPlane = SGPIO/i2c SEP
Load Balance Mode = None
Security Key Assigned = Off
Disable Online Controller Reset = Off
Use drive activity for locate = Off
Boot :
====
Max Drives to Spinup at One Time = 0
Maximum number of direct attached drives to spin up in 1 min = 0
Delay Among Spinup Groups (sec) = 0
Allow Boot with Preserved Cache = On
Defaults :
========
Phy Polarity = 0
Phy PolaritySplit = 0
Cached IO = Off
Default spin down time (mins) = 0
Coercion Mode = None
ZCR Config = Unknown
Max Chained Enclosures = 0
Direct PD Mapping = No
Restore Hot Spare on Insertion = No
Expose Enclosure Devices = No
Maintain PD Fail History = No
Zero Based Enclosure Enumeration = No
Disable Puncturing = No
Un-Certified Hard Disk Drives = Block
SMART Mode = Mode 6
Enable LED Header = No
LED Show Drive Activity = No
Dirty LED Shows Drive Activity = No
EnableCrashDump = No
Disable Online Controller Reset = No
Treat Single span R1E as R10 = No
Power Saving option = Enable
TTY Log In Flash = No
Auto Enhanced Import = No
Enable Shield State = No
Time taken to detect CME = 60 sec
Capabilities :
============
Supported Drives = SAS, SATA, NVMe
Enable JBOD = Yes
Max Parallel Commands = 6656
Max SGE Count = 128
Max Data Transfer Size = 32 sectors
Max Strips PerIO = 0
Max Configurable CacheCade Size = 0
Min Strip Size = 512Bytes
Max Strip Size = 512Bytes
Scheduled Tasks = NA
Security Protocol properties :
============================
Security Protocol = None
When firmware is installed it says 0 hdds found.
Can someone tell me what i am doing wrong ?
i have noticed that few members of sth have same series HBA as i do.
I have bought 2 cards and i have tried one so far.
Updated to latest firmware.
Drives 1tb wd blue and crucial BX 240g for test. Cables cbl-sast-0631 (sff to 4x sata)
Computer dell T320 fitted in x16 slot.
NVME for test is shipped (waiting) and cable will be cbl-sast-0957
output of show all
[root@localhost ~]# /opt/MegaRAID/storcli/storcli64 /c0 show all
CLI Version = 007.1504.0000.0000 June 22, 2020
Operating system = Linux 3.10.0-1127.el7.x86_64
Controller = 0
Status = Success
Description = None
Basics :
======
Controller = 0
Adapter Type = SAS3616(B0)
Model = HBA 9405W-16i
Serial Number = SP94572070
Current System Date/time = 09/29/2020 17:04:59
Concurrent commands supported = 6656
SAS Address = 500605b00fba45e0
PCI Address = 00:0a:00:00
Mfg Date = 00/00/00
Rework Date = 00/00/00
Revision No = N/A
Version :
=======
Firmware Package Build = 16.00.00.00
Firmware Version = 16.00.00.00
Bios Version = 09.09.00.00_16.00.00.00
NVDATA Version = 15.12.00.15
PSOC Version = 05689001
Driver Name = mpt3sas
Driver Version = 31.100.01.00
PCI Version :
===========
Vendor Id = 0x1000
Device Id = 0xD1
SubVendor Id = 0x1000
SubDevice Id = 0x3090
Host Interface = PCIE
Device Interface = SAS-12G
Bus Number = 10
Device Number = 0
Function Number = 0
Domain ID = 0
Pending Images in Flash :
=======================
Image name = No pending images
Status :
======
Controller Status = OK
Memory Correctable Errors = 0
Memory Uncorrectable Errors = 0
Bios was not detected during boot = No
Controller has booted into safe mode = No
Controller has booted into certificate provision mode = No
Supported Adapter Operations :
============================
Alarm Control = No
Cluster Support = No
Self Diagnostic = No
Deny SCSI Passthrough = No
Deny SMP Passthrough = No
Deny STP Passthrough = No
Support more than 8 Phys = Yes
FW and Event Time in GMT = No
Support Enclosure Enumeration = Yes
Support Allowed Operations = Yes
Support Multipath = Yes
Support Security = No
Support Config Page Model = No
Support the OCE without adding drives = No
support EKM = No
Snapshot Enabled = No
Support PFK = No
Support PI = No
Support Shield State = No
Support Set Link Speed = No
Support JBOD = No
Disable Online PFK Change = No
Real Time Scheduler = No
Support Reset Now = No
Support Emulated Drives = No
Support Secure Boot = No
Support Platform Security = No
HwCfg :
=====
ChipRevision = B0
BatteryFRU = N/A
Front End Port Count = 1
Backend Port Count = 21
Serial Debugger = Absent
NVRAM Size = 0KB
Flash Size = 16MB
On Board Memory Size = 0MB
On Board Expander = Absent
Temperature Sensor for ROC = Present
Temperature Sensor for Controller = Absent
Current Size of CacheCade (GB) = 0
Current Size of FW Cache (MB) = 0
ROC temperature(Degree Celcius) = 51
Policies :
========
Policies Table :
==============
------------------------------------------------
Policy Current Default
------------------------------------------------
Predictive Fail Poll Interval 0 sec
Interrupt Throttle Active Count 0
Interrupt Throttle Completion 0 us
Rebuild Rate 0 % 30%
PR Rate 0 % 30%
BGI Rate 0 % 30%
Check Consistency Rate 0 % 30%
Reconstruction Rate 0 % 30%
Cache Flush Interval 0s
------------------------------------------------
Flush Time(Default) = 4s
Drive Coercion Mode = none
Auto Rebuild = Off
Battery Warning = Off
ECC Bucket Size = 0
ECC Bucket Leak Rate (hrs) = 0
Restore HotSpare on Insertion = Off
Expose Enclosure Devices = Off
Maintain PD Fail History = Off
Reorder Host Requests = On
Auto detect BackPlane = SGPIO/i2c SEP
Load Balance Mode = None
Security Key Assigned = Off
Disable Online Controller Reset = Off
Use drive activity for locate = Off
Boot :
====
Max Drives to Spinup at One Time = 0
Maximum number of direct attached drives to spin up in 1 min = 0
Delay Among Spinup Groups (sec) = 0
Allow Boot with Preserved Cache = On
Defaults :
========
Phy Polarity = 0
Phy PolaritySplit = 0
Cached IO = Off
Default spin down time (mins) = 0
Coercion Mode = None
ZCR Config = Unknown
Max Chained Enclosures = 0
Direct PD Mapping = No
Restore Hot Spare on Insertion = No
Expose Enclosure Devices = No
Maintain PD Fail History = No
Zero Based Enclosure Enumeration = No
Disable Puncturing = No
Un-Certified Hard Disk Drives = Block
SMART Mode = Mode 6
Enable LED Header = No
LED Show Drive Activity = No
Dirty LED Shows Drive Activity = No
EnableCrashDump = No
Disable Online Controller Reset = No
Treat Single span R1E as R10 = No
Power Saving option = Enable
TTY Log In Flash = No
Auto Enhanced Import = No
Enable Shield State = No
Time taken to detect CME = 60 sec
Capabilities :
============
Supported Drives = SAS, SATA, NVMe
Enable JBOD = Yes
Max Parallel Commands = 6656
Max SGE Count = 128
Max Data Transfer Size = 32 sectors
Max Strips PerIO = 0
Max Configurable CacheCade Size = 0
Min Strip Size = 512Bytes
Max Strip Size = 512Bytes
Scheduled Tasks = NA
Security Protocol properties :
============================
Security Protocol = None
When firmware is installed it says 0 hdds found.
Can someone tell me what i am doing wrong ?