C:\Program Files\smartmontools\bin>smartctl -ax pd2
smartctl 6.5 2016-05-07 r4318 [x86_64-w64-mingw32-2012r2] (sf-6.5-1)
Copyright (C) 2002-16, Bruce Allen, Christian Franke,
www.smartmontools.org
=== START OF INFORMATION SECTION ===
Vendor: WD
Product: WDC WD4001FYYG-0
Revision: VR07
Compliance: SPC-4
User Capacity: 4,000,787,030,016 bytes [4.00 TB]
Logical block size: 512 bytes
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Logical Unit id: 0x50000c0f01d138ac
Serial number: WMC1F0887091
Device type: disk
Transport protocol: SAS (SPL-3)
Local Time is: Tue Apr 26 14:17:10 2022 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
Temperature Warning: Enabled
Read Cache is: Enabled
Writeback Cache is: Disabled
=== START OF READ SMART DATA SECTION ===
SMART Health Status: HARDWARE IMPENDING FAILURE TOO MANY BLOCK REASSIGNS [asc=5d
, ascq=14]
Current Drive Temperature: 35 C
Drive Trip Temperature: 69 C
Manufactured in week 46 of year 2013
Specified cycle count over device lifetime: 1048576
Accumulated start-stop cycles: 899
Specified load-unload count over device lifetime: 1114112
Accumulated load-unload cycles: 1
Elements in grown defect list: 1821
Error counter log:
Errors Corrected by Total Correction Gigabytes Tot
al
ECC rereads/ errors algorithm processed unc
orrected
fast | delayed rewrites corrected invocations [10^9 bytes] err
ors
read: 87584 608 3250 88192 613 161096.649
5
write: 138916 824 3422 139740 882 86809.261
0
Non-medium error count: 2355
SMART Self-test log
Num Test Status segment LifeTime LBA_first_err [
SK ASC ASQ]
Description number (hours)
# 1 Default Completed - 1028 - [
- - -]
# 2 Default Completed - 1028 - [
- - -]
Long (extended) Self Test duration: 31120 seconds [518.7 minutes]
Background scan results log
Status: no scans active
Accumulated power on time, hours:minutes 4926:05 [295565 minutes]
Number of background scans performed: 0, scan progress: 0.00%
Number of background medium scans performed: 0
Protocol Specific port log page for SAS SSP
relative target port id = 1
generation code = 0
number of phys = 1
phy identifier = 0
attached device type: SAS or SATA device
attached reason: unknown
reason: unknown
negotiated logical link rate: phy enabled; 6 Gbps
attached initiator port: ssp=1 stp=1 smp=1
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x50000c0f01d138ae
attached SAS address = 0x5003048011bf3c01
attached phy identifier = 7
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization = 1
Phy reset problem = 0
Phy event descriptors:
Transmitted SSP frame error count: 0
Received SSP frame error count: 0
relative target port id = 2
generation code = 0
number of phys = 1
phy identifier = 1
attached device type: no device attached
attached reason: unknown
reason: unknown
negotiated logical link rate: phy enabled; unknown
attached initiator port: ssp=0 stp=0 smp=0
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x50000c0f01d138af
attached SAS address = 0x0
attached phy identifier = 0
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization = 0
Phy reset problem = 0
Phy event descriptors:
Transmitted SSP frame error count: 0
Received SSP frame error count: 0
C:\Program Files\smartmontools\bin>