There's nothing sketchy in the SMART data. Looks like the vendor, serial #, and revision all match up to the exterior label:
Prior to my installation the disk was only on for 50 hours and has 1.2 Petabytes read and 382 Terabytes write which can't be correct. I must be misreading the SMART data?
Code:
> root@flash[~]# smartctl -x /dev/da0
smartctl 7.1 2019-12-30 r5022 [FreeBSD 12.2-RELEASE-p2 amd64] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Vendor: HGST
Product: HUSTV1576ASS200
Revision: a473
Compliance: SPC-4
User Capacity: 7,681,501,126,656 bytes [7.68 TB]
Logical block size: 512 bytes
Physical block size: 4096 bytes
LU is resource provisioned, LBPRZ=1
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
Logical Unit id: 0x5000cca08d00101c
Serial number: 5WV0128X
Device type: disk
Transport protocol: SAS (SPL-3)
Local Time is: Mon Feb 1 00:48:07 2021 PST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
Temperature Warning: Enabled
Read Cache is: Enabled
Writeback Cache is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK
Percentage used endurance indicator: 2%
Current Drive Temperature: 44 C
Drive Trip Temperature: 70 C
Manufactured in week 42 of year 2017
Specified cycle count over device lifetime: 0
Accumulated start-stop cycles: 0
Specified load-unload count over device lifetime: 0
Accumulated load-unload cycles: 0
Elements in grown defect list: 0
Vendor (Seagate Cache) information
Blocks sent to initiator = 213633194493214720
Error counter log:
Errors Corrected by Total Correction Gigabytes Total
ECC rereads/ errors algorithm processed uncorrected
fast | delayed rewrites corrected invocations [10^9 bytes] errors
read: 0 0 0 0 0 1211152.359 0
write: 0 0 0 0 0 382196.144 0
Non-medium error count: 0
SMART Self-test log
Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ]
Description number (hours)
# 1 Background short Completed - 1181 - [- - -]
# 2 Background long Completed - 1179 - [- - -]
Long (extended) Self-test duration: 1320 seconds [22.0 minutes]
Background scan results log
Status: no scans active
Accumulated power on time, hours:minutes 1181:42 [70902 minutes]
Number of background scans performed: 0, scan progress: 0.00%
Number of background medium scans performed: 0
Protocol Specific port log page for SAS SSP
relative target port id = 1
generation code = 1
number of phys = 1
phy identifier = 0
attached device type: expander device
attached reason: SMP phy control function
reason: unknown
negotiated logical link rate: phy enabled; 6 Gbps
attached initiator port: ssp=0 stp=0 smp=0
attached target port: ssp=0 stp=0 smp=1
SAS address = 0x5000cca08d00101d
attached SAS address = 0x50030480007796bf
attached phy identifier = 12
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization = 0
Phy reset problem = 0
Phy event descriptors:
Invalid word count: 0
Running disparity error count: 0
Loss of dword synchronization count: 0
Phy reset problem count: 0
relative target port id = 2
generation code = 1
number of phys = 1
phy identifier = 1
attached device type: no device attached
attached reason: unknown
reason: unknown
negotiated logical link rate: phy enabled; unknown
attached initiator port: ssp=0 stp=0 smp=0
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000cca08d00101e
attached SAS address = 0x0
attached phy identifier = 0
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization = 0
Phy reset problem = 0
Phy event descriptors:
Invalid word count: 0
Running disparity error count: 0
Loss of dword synchronization count: 0
Phy reset problem count: 0