Hey man, did you ever get this thing running? I am planning a similar build with X11SPL-F for my networking lab (I presume you are to - CCIE?)...
Unfortunately the processor has been backordered for awhile (since mid December). I would of cancelled and ordered elsewhere but was promised twice that it would be here early January. Finally got shipment confirmation and should be here Monday. I have everything else and with photos below though:Hey man, did you ever get this thing running? I am planning a similar build with X11SPL-F for my networking lab (I presume you are to - CCIE?)...
I would try replacing the cable and see if that helps, another thing to look into is the firmware version on your 9300 I think P20 is the recommended and supported version for freenas.
Avago Technologies SAS3 Flash Utility
Version 15.00.00.00 (2016.11.17)
Copyright 2008-2016 Avago Technologies. All rights reserved.
Adapter Selected is a Avago SAS: SAS3008(C0)
Controller Number : 0
Controller : SAS3008(C0)
PCI Address : 00:03:00:00
SAS Address : 500605b-0-0898-a680
NVDATA Version (Default) : 0e.00.00.07
NVDATA Version (Persistent) : 0e.00.00.07
Firmware Product ID : 0x2221 (IT)
Firmware Version : 15.00.02.00
NVDATA Vendor : LSI
NVDATA Product ID : SAS9300-8i
BIOS Version : N/A
UEFI BSD Version : N/A
FCODE Version : N/A
Board Name : SAS9300-8i
Board Assembly : N/A
Board Tracer Number : N/A
Finished Processing Commands Successfully.
Exiting SAS3Flash.
smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.1-STABLE amd64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: HGST HDN728080ALE604
Serial Number:
LU WWN Device Id: 5 000cca 261cceb34
Firmware Version: A4GNW91X
User Capacity: 8,001,563,222,016 bytes [8.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Mon Feb 12 20:10:24 2018 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 101) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: (1108) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 132 132 054 Pre-fail Offline - 112
3 Spin_Up_Time 0x0007 146 146 024 Pre-fail Always - 451 (Average 452)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 11
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 128 128 020 Pre-fail Offline - 18
9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 252
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 11
22 Unknown_Attribute 0x0023 100 100 025 Pre-fail Always - 100
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 29
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 29
194 Temperature_Celsius 0x0002 166 166 000 Old_age Always - 36 (Min/Max 22/37)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 6
SMART Error Log Version: 1
ATA Error Count: 6 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 6 occurred at disk power-on lifetime: 247 hours (10 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 00 20 60 26 44 40 00 00:51:27.143 WRITE FPDMA QUEUED
2f 00 01 10 00 00 00 00 00:51:27.143 READ LOG EXT
61 50 30 60 28 44 40 00 00:51:27.141 WRITE FPDMA QUEUED
61 00 28 60 27 44 40 00 00:51:27.141 WRITE FPDMA QUEUED
61 00 18 60 25 44 40 00 00:51:27.141 WRITE FPDMA QUEUED
Error 5 occurred at disk power-on lifetime: 247 hours (10 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 20 00 e8 21 40 40 00 00:38:37.673 WRITE FPDMA QUEUED
2f 00 01 10 00 00 00 00 00:38:37.673 READ LOG EXT
61 08 00 e0 21 40 40 00 00:38:37.672 WRITE FPDMA QUEUED
61 08 00 d8 21 40 40 00 00:38:37.672 WRITE FPDMA QUEUED
ea 00 00 00 00 00 00 00 00:38:33.575 FLUSH CACHE EXT
Error 4 occurred at disk power-on lifetime: 247 hours (10 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 58 00 18 7b 40 40 00 00:37:55.387 WRITE FPDMA QUEUED
2f 00 01 10 00 00 00 00 00:37:55.387 READ LOG EXT
61 58 00 c0 7a 40 40 00 00:37:55.386 WRITE FPDMA QUEUED
61 28 00 18 22 40 40 00 00:37:55.386 WRITE FPDMA QUEUED
61 58 00 68 7a 40 40 00 00:37:55.386 WRITE FPDMA QUEUED
Error 3 occurred at disk power-on lifetime: 245 hours (10 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 00 00 a0 d7 43 40 00 00:11:05.278 WRITE FPDMA QUEUED
2f 00 01 10 00 00 00 00 00:11:05.278 READ LOG EXT
61 c8 10 a0 d9 43 40 00 00:11:05.277 WRITE FPDMA QUEUED
61 00 08 a0 d8 43 40 00 00:11:05.277 WRITE FPDMA QUEUED
61 e8 10 b8 d6 43 40 00 00:11:05.275 WRITE FPDMA QUEUED
Error 2 occurred at disk power-on lifetime: 245 hours (10 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 80 00 a0 e0 40 40 00 00:10:45.710 WRITE FPDMA QUEUED
2f 00 01 10 00 00 00 00 00:10:45.710 READ LOG EXT
61 20 00 80 e0 40 40 00 00:10:45.709 WRITE FPDMA QUEUED
61 c8 08 b8 df 40 40 00 00:10:45.699 WRITE FPDMA QUEUED
61 00 00 b8 de 40 40 00 00:10:45.699 WRITE FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 134 -
# 2 Extended offline Completed without error 00% 111 -
# 3 Extended offline Aborted by host 60% 93 -
# 4 Short offline Completed without error 00% 84 -
# 5 Short offline Completed without error 00% 60 -
# 6 Short offline Completed without error 00% 36 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
(da11:mpr0:0:18:0): WRITE(10). CDB: 2a 00 40 41 e1 20 00 01 00 00 length 131072 SMID 1013 terminated ioc 804b loginfo 31120303 scsi 0 state c xfer 0
(da11:mpr0:0:18:0): WRITE(10). CDB: 2a 00 40 41 e4 20 00 00 38 00 length 28672 SMID 282 terminated ioc 804b loginfo 31120303 (da11:mpr0:0:18:0): WRITE(10). CDB: 2a 00 40 41 e1 20 00 01 00 00
scsi 0 state c xfer 0
(da11:mpr0:0:18:0): WRITE(10). CDB: 2a 00 40 41 e3 20 00 01 00 00 length 131072 SMID 330 terminated ioc 804b loginfo 31120303 scsi 0 state c xfer 0
(da11:mpr0:0:18:0): WRITE(10). CDB: 2a 00 40 41 e2 20 00 01 00 00 length 131072 SMID 989 terminated ioc 804b loginfo 31120303 scsi 0 state c xfer 0
(da11:mpr0:0:18:0): CAM status: CCB request completed with an error
(da11:mpr0:0:18:0): Retrying command
(da11:mpr0:0:18:0): WRITE(10). CDB: 2a 00 40 41 e4 20 00 00 38 00
(da11:mpr0:0:18:0): CAM status: CCB request completed with an error
(da11:mpr0:0:18:0): Retrying command
(da11:mpr0:0:18:0): WRITE(10). CDB: 2a 00 40 41 e3 20 00 01 00 00
(da11:mpr0:0:18:0): CAM status: CCB request completed with an error
(da11:mpr0:0:18:0): Retrying command
(da11:mpr0:0:18:0): WRITE(10). CDB: 2a 00 40 41 e2 20 00 01 00 00
(da11:mpr0:0:18:0): CAM status: CCB request completed with an error
(da11:mpr0:0:18:0): Retrying command
(da11:mpr0:0:18:0): WRITE(10). CDB: 2a 00 40 41 e1 20 00 01 00 00
(da11:mpr0:0:18:0): CAM status: SCSI Status Error
(da11:mpr0:0:18:0): SCSI status: Check Condition
(da11:mpr0:0:18:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
(da11:mpr0:0:18:0): Retrying command (per sense data)
(da20:mpr0:0:27:0): WRITE(10). CDB: 2a 00 40 43 5e 18 00 00 b8 00 length 94208 SMID 292 terminated ioc 804b loginfo 31120303 scsi 0 state c xfer 0
(da20:mpr0:0:27:0): WRITE(10). CDB: 2a 00 40 43 5d 18 00 01 00 00 length 131072 SMID 434 terminated ioc 804b loginfo 31120303(da20:mpr0:0:27:0): WRITE(10). CDB: 2a 00 40 43 5e 18 00 00 b8 00
scsi 0 state c xfer 0
(da20:mpr0:0:27:0): CAM status: CCB request completed with an error
(da20:mpr0:0:27:0): Retrying command
(da20:mpr0:0:27:0): WRITE(10). CDB: 2a 00 40 43 5d 18 00 01 00 00
(da20:mpr0:0:27:0): CAM status: CCB request completed with an error
(da20:mpr0:0:27:0): Retrying command
(da20:mpr0:0:27:0): WRITE(10). CDB: 2a 00 40 43 5d 18 00 01 00 00
(da20:mpr0:0:27:0): CAM status: SCSI Status Error
(da20:mpr0:0:27:0): SCSI status: Check Condition
(da20:mpr0:0:27:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
(da20:mpr0:0:27:0): Retrying command (per sense data)
(da13:mpr0:0:20:0): WRITE(10). CDB: 2a 00 40 45 16 48 00 01 00 00 length 131072 SMID 333 terminated ioc 804b loginfo 31120303 scsi 0 state c xfer 0
(da13:mpr0:0:20:0): WRITE(10). CDB: 2a 00 40 45 19 48 00 01 00 00 length 131072 SMID 297 terminated ioc 804b loginfo 31120303(da13:mpr0:0:20:0): WRITE(10). CDB: 2a 00 40 45 16 48 00 01 00 00
scsi 0 state c xfer 0
(da13:mpr0:0:20:0): WRITE(10). CDB: 2a 00 40 45 1a 48 00 00 f0 00 length 122880 SMID 624 terminated ioc 804b loginfo 31120303 scsi 0 state c xfer 0
(da13:mpr0:0:20:0): WRITE(10). CDB: 2a 00 40 45 15 48 00 01 00 00 length 131072 SMID 663 terminated ioc 804b loginfo 31120303 scsi 0 state c xfer 0
(da13:mpr0:0:20:0): WRITE(10). CDB: 2a 00 40 45 14 48 00 01 00 00 length 131072 SMID 337 terminated ioc 804b loginfo 31120303 scsi 0 state c xfer 0
(da13:mpr0:0:20:0): WRITE(10). CDB: 2a 00 40 45 13 48 00 01 00 00 length 131072 SMID 806 terminated ioc 804b loginfo 31120303 scsi 0 state c xfer 0
(da13:mpr0:0:20:0): WRITE(10). CDB: 2a 00 40 45 17 48 00 01 00 00 length 131072 SMID 251 terminated ioc 804b loginfo 31120303(da13:mpr0:0:20:0): CAM status: CCB request completed with an error
(da13:mpr0:0:20:0): Retrying command
(da13:mpr0:0:20:0): WRITE(10). CDB: 2a 00 40 45 19 48 00 01 00 00
(da13:mpr0:0:20:0): CAM status: CCB request completed with an error
(da13:mpr0:0:20:0): Retrying command
(da13:mpr0:0:20:0): WRITE(10). CDB: 2a 00 40 45 1a 48 00 00 f0 00
scsi 0 state c xfer 0
(da13:mpr0:0:20:0): WRITE(10). CDB: 2a 00 40 45 18 48 00 01 00 00 length 131072 SMID 311 terminated ioc 804b loginfo 31120303 scsi 0 state c xfer 0
(da13:mpr0:0:20:0): CAM status: CCB request completed with an error
(da13:mpr0:0:20:0): Retrying command
(da13:mpr0:0:20:0): WRITE(10). CDB: 2a 00 40 45 15 48 00 01 00 00
(da13:mpr0:0:20:0): CAM status: CCB request completed with an error
(da13:mpr0:0:20:0): Retrying command
(da13:mpr0:0:20:0): WRITE(10). CDB: 2a 00 40 45 14 48 00 01 00 00
(da13:mpr0:0:20:0): CAM status: CCB request completed with an error
(da13:mpr0:0:20:0): Retrying command
(da13:mpr0:0:20:0): WRITE(10). CDB: 2a 00 40 45 13 48 00 01 00 00
(da13:mpr0:0:20:0): CAM status: CCB request completed with an error
(da13:mpr0:0:20:0): Retrying command
(da13:mpr0:0:20:0): WRITE(10). CDB: 2a 00 40 45 17 48 00 01 00 00
(da13:mpr0:0:20:0): CAM status: CCB request completed with an error
(da13:mpr0:0:20:0): Retrying command
(da13:mpr0:0:20:0): WRITE(10). CDB: 2a 00 40 45 18 48 00 01 00 00
(da13:mpr0:0:20:0): CAM status: CCB request completed with an error
(da13:mpr0:0:20:0): Retrying command
(da3:mpr0:0:10:0): WRITE(10). CDB: 2a 00 40 47 42 00 00 01 00 00 length 131072 SMID 386 terminated ioc 804b loginfo 31120303 scsi 0 state c xfer 0
(da3:mpr0:0:10:0): WRITE(10). CDB: 2a 00 40 47 43 00 00 00 e8 00 length 118784 SMID 961 terminated ioc 804b loginfo 31120303 (da3:mpr0:0:10:0): WRITE(10). CDB: 2a 00 40 47 42 00 00 01 00 00
scsi 0 state c xfer 0
(da3:mpr0:0:10:0): CAM status: CCB request completed with an error
(da3:mpr0:0:10:0): Retrying command
(da3:mpr0:0:10:0): WRITE(10). CDB: 2a 00 40 47 43 00 00 00 e8 00
(da3:mpr0:0:10:0): CAM status: CCB request completed with an error
(da3:mpr0:0:10:0): Retrying command
(da3:mpr0:0:10:0): WRITE(10). CDB: 2a 00 40 47 42 00 00 01 00 00
(da3:mpr0:0:10:0): CAM status: SCSI Status Error
(da3:mpr0:0:10:0): SCSI status: Check Condition
(da3:mpr0:0:10:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
(da3:mpr0:0:10:0): Retrying command (per sense data)
(da13:mpr0:0:20:0): WRITE(10). CDB: 2a 00 40 45 13 48 00 01 00 00
(da13:mpr0:0:20:0): CAM status: SCSI Status Error
(da13:mpr0:0:20:0): SCSI status: Check Condition
(da13:mpr0:0:20:0): SCSI sense: UNIT ATTENTION asc:29,0 (Power on, reset, or bus device reset occurred)
(da13:mpr0:0:20:0): Retrying command (per sense data)
Not familiar with running ZFS over anything other than Freenas. Once I try the above mentioned I may resort to trying it. I assume I can build the initial pool in Freenas, detach the pool, then install another OS and import said pool. But again I am not as familar with ZFS with those other OS's and mostly use the Freenas GUI to get by although can use some command line.OOC, try the same hardware under the same hardware with Linux and/or OmniOS/Napp-it.
Will do a baremetal Freenas install first but I am willing to try another OS. If you got any good tutorial sites or even videos that show what commands to create a pool, allow a guest access/share, and allows SMB for a windows OS to access, I am willing to do it.You should be good with most LSI cards. I've successfully used a mixture of 9207, 9211, 9300 and 9305s all of which worked without issue in IT mode with SAS2 backplanes and a mixture of drives from Seagate & WD.
I'd suggest keeping things simple... install FreeNAS to bare metal, create a 2 drive mirror and validate that works before incrementally adding additional hardware / complexity.
I'd also suggest again value in throwing a Linux system on your hardware to validate too.... Ive had this same issues as this with one model of Seagate drives with FreeNAS I just couldnt get to the bottom of, performance also sucked when it was stable enough to run. Its a single zfs create command to create an array so really isnt very complex or time consuming to do. It appears to be the one thing you havent checked yet and arguably the cheapest and easiest.
Did you mean the homepage or one of the forums? Tried checking a few places and did not see what you were referencing.There was a link on page one to a Napp-it it all-in-one VM you can deploy which makes things trivial if you wish to stay with a GUI approach. Learning some zfs CLI skills wouldnt be a total waste of time though if you go the linux route.