I did not take note of it, I can look on the second one that I got if you want.
Should only be a problem if you don't have a v3 CPU to put into it.
-JCL
Supermicro X10SRH-CF
- Thread starter jcl333
- Start date
Notice: Page may contain affiliate links for which we may earn a small commission through services like Amazon Affiliates or Skimlinks.
Should only be a problem if you don't have a v3 CPU to put into it.
-JCL
Need to get all new ram and CPU for this board so bios version will greatly influence selection.
Hi. Mind sharing the procedure to set the fan thresholds? I just installed my board in a Supermicro 846 chassis, and it's trying to send the stock fans into orbit! LOL
My offer for $115 for one got accepted. Maybe I should have started lower 
It will replace my X10SRA that doesn't have IPMI. I need to find a new fan compatible with the narrow ILM, any suggestion, apart for the usual noctua? It's for a desktop case.
It will replace my X10SRA that doesn't have IPMI. I need to find a new fan compatible with the narrow ILM, any suggestion, apart for the usual noctua? It's for a desktop case.
Damn, I should of gone lower then. HahaMy offer for $115 for one got accepted. Maybe I should have started lower
It will replace my X10SRA that doesn't have IPMI. I need to find a new fan compatible with the narrow ILM, any suggestion, apart for the usual noctua? It's for a desktop case.
I've always had good luck with the Supermicro SNK-P0050AP4 which works with both square and narrow ILM
Yup I was looking at this one, it should be silent enough on IDLE and not too noisy under load.Damn, I should of gone lower then. Haha
I've always had good luck with the Supermicro SNK-P0050AP4 which works with both square and narrow ILM
I am a bit "scared" to buy a Noctua, since the on-board BMC control the fan speed and may not like the low RPM fan from Noctua.
You folks are such a bad influence on the wallet. $110 for one. Hoping they have been good with the service for this item. I recently saw comments here on the forum on a different thread that ocean_tech’s recent customer service has deteriorated. Hopefully its due to all the stuff going on with the COVID-19.
SO.. again, cooler question if some of you have experience with some of them, since I need to order one:
- NH-D9DX i4 (3U)
- NH-U9DX i4 (4U)
- NH-U12DX i4 (should fit my tower, but pretty sure it will block some ram slot?)
- SNK-P0050AP4 (had two of them on a dual E52670 v1 build, they didn't seem very noisy at idle or low charge. Plus no need to tweak the BMC fan threshold)
Noctua
+ : with the good mounting kit, can be reused on virtually all platform
+: more silence
-: pricey
-: have to run them at full to avoid threshold issue? Or run a scruipt every time the PC is rebooted?
SNK-P0050AP4
+: directly compatible, no question asked
+: less expensive
-: more noise than the Noctua, but by how much?
-: cannot be reused on another platform
- NH-D9DX i4 (3U)
- NH-U9DX i4 (4U)
- NH-U12DX i4 (should fit my tower, but pretty sure it will block some ram slot?)
- SNK-P0050AP4 (had two of them on a dual E52670 v1 build, they didn't seem very noisy at idle or low charge. Plus no need to tweak the BMC fan threshold)
Noctua
+ : with the good mounting kit, can be reused on virtually all platform
+: more silence
-: pricey
-: have to run them at full to avoid threshold issue? Or run a scruipt every time the PC is rebooted?
SNK-P0050AP4
+: directly compatible, no question asked
+: less expensive
-: more noise than the Noctua, but by how much?
-: cannot be reused on another platform