obvi, that makes sense, my bad.
Ok time to do some ebay shopping!
Nothing else to consider right?
Intel 8124m board compatibility
- Thread starter Rand__
- Start date
Notice: Page may contain affiliate links for which we may earn a small commission through services like Amazon Affiliates or Skimlinks.
Ok time to do some ebay shopping!
Nothing else to consider right?
but manuals say:
Only populate DIMMA2 and DIMMD2 if the extra memory support is needed
(some say these two extra slots are only to match 1TB Memory)
personaly i would buy 6x 16GB RDIMM and let A2/D2 empty.
OMG that makes it so much easier to shop and match!
I think I found a nice set of 6x 32GB ECC RDIMM DDR4-2666 which should do the trick
Thanks for the awesomeness!
I keep my fingers crossed that these processors are still in good condition. Do you already have a motherboard where they should be in?
P-8136 is only 165W TDP not the problem, problem is missing microcode and my erperience is not much good with latest BIOS+B1 MC
the P-8136 / P-8124 must be bad then, but i have not one of these to test B1 stepping. i have only 16 core unlocked QLKH
here is another thread with specialy the P8124. bad TIM runs hot.
or use some (good/not too much,not too less) thermal paste. AFAIK cascade lake is not soldered like skylake, the TIM may bad after long time of use. have you used water ? the QL2K 26 core can go 3200mhz all core still air cooled, but more requires water then.
check the core temps for songle major differendes in temp. i.e. a bad P-8124 had temps from 59 to 88 degree same run.
no way, sorry.
dynatron use the old style TDP definition, and sometimes they can't even do that. only 205W for a short time. the vapor chamber is the limiting part.
EPYC solderd. not work with this(or you have to change physics). 8275cl is custom, needs custom cooling.
Which coolers would you recommend? Just in case somebody happens to stumble upon more of these in the future?
take a look into HWinfo package power at CBR23 run. then choose a cooler which can do this continious.
IMHO 1U can not.
checked the temps for major differences between core ? or is that a secret ? don't have HWinfo ? you ran CBR23 so i thought you run windows.
Hey @Randomer Naught I forgot to ask you, did you ended up seating the 8275cl in those EPC621D8A boards?
Oh yea, and please throw those temps in an chart or dump the raw info into a quote line, very curious to see how much of a temp improvement you got.
Later this year I want to try watercooling one or two of those 8275cl beasts with two 560 rads, if it works I want to try to get protocase to build a dedicated cooling chassis for the rads and pumps (though I have to figure out what where to put my UPS then).
Oh yea, and please throw those temps in an chart or dump the raw info into a quote line, very curious to see how much of a temp improvement you got.
Later this year I want to try watercooling one or two of those 8275cl beasts with two 560 rads, if it works I want to try to get protocase to build a dedicated cooling chassis for the rads and pumps (though I have to figure out what where to put my UPS then).
Last edited:
@RolloZ170 Is it possible to change the TDC for dell servers (eg r740) to support OEM processors? Did you had any change on these motherboards?
Last edited:
made this on a Dell 7820
Dell uses PXE1610C (Primarion, overtaken from Infineon)
PXE1610C uses a proprietäry method to store the register to NVM(OTP2), so needed a primarion USB dongle and PowerCode software(with activation key) to change the ICC_MAX.
the R740 motherboard mostly missing the 6th phase(or more) the 7820 has 6+1 phase installed.
Last edited: