Are you sure you followed the guide by the OP in this thread - i have done about 6 of the 6450 and not had a single issue with SSH (other than Putty whinging that the cipher is old)
In the same Guide fohdeesha shows how to turn off stacking.
Failing that check the Youtube channel for the...
@fohdeesha - doing this will allow me to use the other two 40GB slots for straight connection (not fanout) to my Connect X3 cards ? So i could use 2 ports on the first switch for ESXi hosts and one on the 2nd switch for another host ? Or does this config lock the ports into fanout mode etc ?
Craig
OK so lets take it step by step
A port is a trunk port on a 6610 by adding more than 1 VLAN to it (or in ICX parlance) adding it to more than 1 VLAN
Usually the 4095 VLAN is used for management traffic (by convention - not by hardcoding)
If you have a Unifi connected to a switch port - where...
OK i had a quick look - i think you havve a basic misunderstanding - yes ports can be dual mode (tagged and untagged traffic) but in your case for the ESXI servers they will be trunk ports - untagged traffic is simply traffic that comes from a device that does not understand VLANs and the switch...
Hey Guys,
I have a couple of 6610s here - one is my testing and messing around one and the other in production.
Currently i am using two of the rear ports at 40Gb/s into Mellanox cards in my ESXi cluster.
I could really use a 3rd one though for my final host
At the moment i am using the 2 x...
Just wondering if you have had time to do this yet ? I am about to purchase a Unit to replace an older 9200 series and would like a known working guide to follow.
regards
Craig
I think @fohdeesha meant to create a VLAN without adding a VE to it and then adding an IP address to the port.
i.e. it is a member of a L2 VLAN and you give it an IP address.
Craig
Post up your config maybe - but as long as you have the inline power options you should be good.
I was reading the manual the other day looking for something and i saw there are different styles of POE that can be enabled - is this an old camera ? May be worth reading up on those and also how...
OK more updates on my attempts to get these switches working reliably with Intel 10Gb adapters and ESXi
So i have a new testbed setup
2 x 6450 standard setup as per fohdeesha's docs - all licensing done etc.
Lets call them switch 1 and switch 2
I have connected the two 6450 via the 1/2/1...
No there is no default IP applied to the port until you do so through the console cable
I am not aware of anyway to (programmatically) disable the ports - someone may have damaged them but seems unlikely - more often than not it is a faulty cable/port on the computer end - personally for $10 or...
I thought i might try and add to the knowledgepool so tried fodeeshas debug using the serial console - linked here
https://forums.servethehome.com/index.php?threads/brocade-icx-series-cheap-powerful-10gbe-40gbe-switching.21107/post-198322
But i got an error on i2c read - when doing this on a...
Just as a follow up to this - i have used the same Intel Coded fibre cable now between a 6610 1/3/x port and an Intel Dual port 82599 card in a linux box and it will not come up at 10GB either
On the 6610 it shows
Type ? for a list
SSH@6610-Basement#show media e 1/3/5
Port 1/3/5: Type ...
6450 - which do i believe ?
Guys - 2 x 6450 - licensed and configured as per OP document - no issues
I have a couple of different SFP+ cables
1) 10GTek - AOC SFP+ 20m fibre - as per here - https://www.amazon.com.au/dp/B08TSZ5TH1?ref=ppx_yo2ov_dt_b_product_details&th=1
2) No name 1m DAC SFP+...
Just wanted to ask - can the 4 ports on the back of the 6610 all be used as 40GB for NIC attachment - or do the breakout ports have to be used as breakout ports
I still have not managed to solve my problem with the disabling of ports in ESXi when i make VLAN changes - but by using 40GB NICs i...
I do not believe there are any known issues with those NICs.
I have just setup my Mellanox CX354 (single port) with a 40GB QSFP cable straight into 1/2/1 and 1/2/6 and had no problems.
Craig
Post your switch config again - i have not used the 40G ports (but am about to when my cables arrive) - is there anything special that needs to be done to put them into 40Gb mode instead of stacking mode ?
Craig
OK well we would expect the serial cable to work - just confirming is it a DB9 serial or a USB Serial ?
Forgive me for asking - but you are plugging it into the correct (serial/console) management port - not the LAN management port (as they are both RJ45)
DO you have any other apps on your...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.