Recent content by animefans

  1. A

    Network segment for storage only

    I have a very small network at home, with ICX7150 as my primary/"core" switch I would like to setup a separate segment just for storage, and use jumbo frame this separate segment will be running thru microtik CRS305-1G-4S+IN The GBE port will connect to my primary network, while the SFP port...
  2. A

    Flapping NIC

    Thanks for the firmware update tip! TIL
  3. A

    Flapping NIC

    I already tried your max|send|receive setting, and somehow it's not working for me I need to find more time to fiddle with it My box is down for now, so can't provide any data... As far as pciutils version, yours is from latest (note Branch 151036.1) [root@hedgehoggrifter:~] $ pkg info...
  4. A

    Flapping NIC

    Just found out this is a thing in Omni OS :) pkg update After updating to latest 151036m, lspci is working kkfong@nappit:~$ sudo lspci -nnv |grep Giga 01:00.0 Ethernet controller [0200]: Intel Corporation 82599ES 10-Gigabit SFI/SFP+ Network Connection [8086:10fb] (rev 01) 01:00.1 Ethernet...
  5. A

    Flapping NIC

    I learn about that Brocade/Ruckus/Comscope router from non other than this forum :) I got mine from ebay, and some seller claim it comes "free" as part of their new home setup I will certainly look for a compatible SFP+ module that will work for the microtik switch (likely fs.com) This is...
  6. A

    Flapping NIC

    Thanks for your feedback! Just for the heck of it, instead of using SFP+ port on Microtik Switch CRS305-1G-4S+, I plugged them into my other router : ICX7150-C12P and no more flapping NIC stays up and I can do ping and iperf3 between the two devices that are on the same subnet It seems like...
  7. A

    Flapping NIC

    I think that's what it's called? This is in my dmesg Jan 24 22:32:44 nappit mac: [ID 435574 kern.info] NOTICE: ixgbe0 link up, 10000 Mbps, full duplex Jan 24 22:32:45 nappit mac: [ID 486395 kern.info] NOTICE: ixgbe0 link down Jan 24 22:32:45 nappit mac: [ID 435574 kern.info] NOTICE: ixgbe0 link...
  8. A

    napp-it 14b AIO upgrade path?

    Finally find some time to play with COMSTAR using the GUI (was doing it using CLI in my last setup), and its not too bad I think I will just start from scratch with all the LU/target/view/etc Again, thank you very much for your assistance!
  9. A

    napp-it 14b AIO upgrade path?

    looks like edit post doesnt count as new message... Is there anyway to "migrate" iSCSI setting from one machine to the next?
  10. A

    napp-it 14b AIO upgrade path?

    Gea Thank you for the details! I will try it out EDIT: Just followed the steps above, and I am on latest napp-it now! BTW, is it possible to "export" the old iSCSI config from my old install and import into the new one?
  11. A

    napp-it 14b AIO upgrade path?

    I am on vmware 5.5 running napp-it 14b vm image for the longest time What is my upgrade path for my napp-it installation? If possible, I prefer to stay with vmware 5.5 Thanks!
  12. A

    WTB 2 x 8GB 240-Pin DDR3 SDRAM 1333 (PC3 10600) RAM

    I want ECC/non registered Thanks!
  13. A

    WTB 2 x 8GB 240-Pin DDR3 SDRAM 1333 (PC3 10600) RAM

    This is for my ancient HP MicroServer N40L Thanks!