Hi guys i just connect my hdd that i only use as backup data sometimes from my server and after copy 12 tb data on it the smart show me some errors and growing list 2 days ago since then no more show up can someone can tell me if its ok if it wont grow any further or i should replace this hdd?I started long smart test as well.Btw after copy 10.5 TB data on this hdd it didnt show any more errors.
Code:
=== START OF INFORMATION SECTION ===
Vendor: HGST
Product: HUH721212AL5200
Revision: A3D0
Compliance: SPC-4
User Capacity: 12,000,138,625,024 bytes [12.0 TB]
Logical block size: 4096 bytes
LU is fully provisioned
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Logical Unit id: 0x5000cca253111180
Serial number: 8DG9BZXD
Device type: disk
Transport protocol: SAS (SPL-3)
Local Time is: Fri Jun 4 20:17:40 2021 BST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
Temperature Warning: Enabled
Read Cache is: Enabled
Writeback Cache is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK
Grown defects during certification = 0
Total blocks reassigned during format = 0
Total new blocks reassigned = 1
Power on minutes since format = 258481
Current Drive Temperature: 37 C
Drive Trip Temperature: 85 C
Manufactured in week 02 of year 2018
Specified cycle count over device lifetime: 50000
Accumulated start-stop cycles: 60
Specified load-unload count over device lifetime: 600000
Accumulated load-unload cycles: 681
Elements in grown defect list: 1
Vendor (Seagate Cache) information
Blocks sent to initiator = 6530337534377984
Error counter log:
Errors Corrected by Total Correction Gigabytes Total
ECC rereads/ errors algorithm processed uncorrected
fast | delayed rewrites corrected invocations [10^9 bytes] errors
read: 0 56 0 56 300165 87653.724 12
write: 0 0 0 0 11061 58066.450 0
verify: 0 0 0 0 4999 0.000 0
Non-medium error count: 0
Self-test execution status: 100% of test remaining
SMART Self-test log
Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ]
Description number (hours)
# 1 Background long Self test in progress ... - NOW - [- - -]
# 2 Background short Completed - 10810 - [- - -]
# 3 Background short Completed - 10718 - [- - -]
# 4 Background long Completed - 10651 - [- - -]
# 5 Background short Completed - 10526 - [- - -]
# 6 Background short Completed - 10406 - [- - -]
# 7 Background short Completed - 10310 - [- - -]
# 8 Background short Completed - 10214 - [- - -]
# 9 Background short Completed - 10022 - [- - -]
#10 Background short Completed - 9830 - [- - -]
#11 Background short Completed - 9662 - [- - -]
#12 Background short Completed - 9566 - [- - -]
#13 Background short Completed - 9470 - [- - -]
#14 Background short Completed - 9374 - [- - -]
#15 Background short Completed - 9182 - [- - -]
#16 Background short Completed - 8822 - [- - -]
#17 Background short Completed - 8726 - [- - -]
#18 Background short Completed - 8630 - [- - -]
#19 Background short Completed - 8534 - [- - -]
#20 Background short Completed - 8342 - [- - -]
Long (extended) Self-test duration: 65535 seconds [1092.2 minutes]
Background scan results log
Status: waiting until BMS interval timer expires
Accumulated power on time, hours:minutes 14935:38 [896138 minutes]
Number of background scans performed: 98, scan progress: 0.00%
Number of background medium scans performed: 98
# when lba(hex) [sk,asc,ascq] reassign_status
1 10725:35 000000008778b098 [3,11,0] Recovered via rewrite in-place
Protocol Specific port log page for SAS SSP
relative target port id = 1
generation code = 1
number of phys = 1
phy identifier = 0
attached device type: expander device
attached reason: loss of dword synchronization
reason: unknown
negotiated logical link rate: phy enabled; 12 Gbps
attached initiator port: ssp=0 stp=0 smp=0
attached target port: ssp=0 stp=0 smp=1
SAS address = 0x5000cca253111181
attached SAS address = 0x5001c450281dccbf
attached phy identifier = 11
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization = 0
Phy reset problem = 0
Phy event descriptors:
Invalid word count: 0
Running disparity error count: 0
Loss of dword synchronization count: 0
Phy reset problem count: 0
relative target port id = 2
generation code = 1
number of phys = 1
phy identifier = 1
attached device type: no device attached
attached reason: unknown
reason: power on
negotiated logical link rate: phy enabled; unknown
attached initiator port: ssp=0 stp=0 smp=0
attached target port: ssp=0 stp=0 smp=0
SAS address = 0x5000cca253111182
attached SAS address = 0x0
attached phy identifier = 0
Invalid DWORD count = 0
Running disparity error count = 0
Loss of DWORD synchronization = 0
Phy reset problem = 0
Phy event descriptors:
Invalid word count: 0
Running disparity error count: 0
Loss of dword synchronization count: 0
Phy reset problem count: 0
Last edited: