Setup:
Dell R620 with 10Gb RJ45 running proxmox (Kratos)
Custom Server with 10Gb SFP+ LC Fiber Connection (Notch)
Synology RS1221 with Synology 10Gb RJ45 NIC (Vault)
Iperf3 Tests Summary
Kratos -> Notch or Vault | 10Gb
Notch -> Vault | 10Gb
Vault -> Notch | 10Gb
Notch or Vault -> Kratos | 4Gb?
I've tried using different cables moving ports chaning the transceiver for kratos but nothing seems to work. I would appreciate anything that would help.
Iperf3 Tests
Kratos (Client) -> Notch (Server)
Notch (Client) -> Kratos (Server)
Ethtool For Kratos 10Gb Interface
Dell R620 with 10Gb RJ45 running proxmox (Kratos)
Custom Server with 10Gb SFP+ LC Fiber Connection (Notch)
Synology RS1221 with Synology 10Gb RJ45 NIC (Vault)
Iperf3 Tests Summary
Kratos -> Notch or Vault | 10Gb
Notch -> Vault | 10Gb
Vault -> Notch | 10Gb
Notch or Vault -> Kratos | 4Gb?
I've tried using different cables moving ports chaning the transceiver for kratos but nothing seems to work. I would appreciate anything that would help.
Iperf3 Tests
Kratos (Client) -> Notch (Server)
Code:
ansible@kratos:~$ iperf3 -c 10.0.0.62
Connecting to host 10.0.0.62, port 5201
[ 5] local 10.0.0.61 port 44990 connected to 10.0.0.62 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 1007 MBytes 8.44 Gbits/sec 0 650 KBytes
[ 5] 1.00-2.00 sec 1.02 GBytes 8.80 Gbits/sec 0 772 KBytes
[ 5] 2.00-3.00 sec 1.04 GBytes 8.96 Gbits/sec 0 1.77 MBytes
[ 5] 3.00-4.00 sec 1.06 GBytes 9.08 Gbits/sec 0 1.77 MBytes
[ 5] 4.00-5.00 sec 1.05 GBytes 9.01 Gbits/sec 0 1.77 MBytes
[ 5] 5.00-6.00 sec 1.03 GBytes 8.89 Gbits/sec 0 1.77 MBytes
[ 5] 6.00-7.00 sec 1.08 GBytes 9.26 Gbits/sec 0 1.77 MBytes
[ 5] 7.00-8.00 sec 1.08 GBytes 9.23 Gbits/sec 0 1.85 MBytes
[ 5] 8.00-9.00 sec 1.07 GBytes 9.17 Gbits/sec 0 1.85 MBytes
[ 5] 9.00-10.00 sec 1.10 GBytes 9.41 Gbits/sec 0 1.85 MBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 10.5 GBytes 9.03 Gbits/sec 0 sender
[ 5] 0.00-10.00 sec 10.5 GBytes 9.02 Gbits/sec receiver
iperf Done.
Code:
ansible@kratos:~$ iperf3 -s
-----------------------------------------------------------
Server listening on 5201
-----------------------------------------------------------
Accepted connection from 10.0.0.62, port 32996
[ 5] local 10.0.0.61 port 5201 connected to 10.0.0.62 port 32998
[ ID] Interval Transfer Bitrate
[ 5] 0.00-1.00 sec 448 MBytes 3.75 Gbits/sec
[ 5] 1.00-2.00 sec 448 MBytes 3.76 Gbits/sec
[ 5] 2.00-3.00 sec 454 MBytes 3.81 Gbits/sec
[ 5] 3.00-4.00 sec 458 MBytes 3.84 Gbits/sec
[ 5] 4.00-5.00 sec 446 MBytes 3.74 Gbits/sec
[ 5] 5.00-6.00 sec 447 MBytes 3.75 Gbits/sec
[ 5] 6.00-7.00 sec 447 MBytes 3.75 Gbits/sec
[ 5] 7.00-8.00 sec 456 MBytes 3.83 Gbits/sec
[ 5] 8.00-9.00 sec 458 MBytes 3.83 Gbits/sec
[ 5] 9.00-10.00 sec 458 MBytes 3.84 Gbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate
[ 5] 0.00-10.00 sec 4.41 GBytes 3.79 Gbits/sec receiver
-----------------------------------------------------------
Server listening on 5201
-----------------------------------------------------------
Code:
ansible@kratos:~$ sudo ethtool vmbr0
Settings for vmbr0:
Supported ports: [ ]
Supported link modes: Not reported
Supported pause frame use: No
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Unknown! (255)
Auto-negotiation: off
Port: Other
PHYAD: 0
Transceiver: internal
Link detected: yes