U-Boot 2009.01 SX_PPC_M460EX SX_3.2.0330-82 ppc (Dec 20 2012 - 17:53:54)
CPU: AMCC PowerPC 460EX Rev. B at 1000 MHz (PLB=166, OPB=83, EBC=83 MHz)
Security/Kasumi support
Bootstrap Option H - Boot ROM Location I2C (Addr 0x52)
Internal PCI arbiter disabled
32 kB I-Cache 32 kB D-Cache
Board: Mellanox PPC460EX Board
FDEF: No
I2C: ready
DRAM: 2 GB (ECC enabled, 333 MHz, CL3)
FLASH: 16 MB
NAND: 1024 MiB
PCI: Bus Dev VenId DevId Class Int
PCIE0: link is not up.
PCIE1: successfully set as root-complex
01 00 15b3 c738 0c06 00
Net: ppc_4xx_eth0, ppc_4xx_eth1
Reading image settings from EEPROM
Mellanox MLNX-OS
Default image: 'PPC_M460EX 3.6.8012 2019-02-22 07:53:42 ppc'
Press Enter to boot this image, or 'Ctrl B' for boot menu
Booting default image in: 0
Mellanox MLNX-OS Boot Menu:
1: PPC_M460EX 3.6.8010 2018-08-20 18:04:16 ppc
* 2: PPC_M460EX 3.6.8012 2019-02-22 07:53:42 ppc
u: USB menu (if USB device connected)
c: Command prompt
Choice:
Entering command prompt
=> setenv mfg_extra_args ramdisk=262144
=> setenv mfg_root 10.10.2.51:/
=> run mfg
Manufacture will DHCP, TFTP from directory 10.10.2.51:/mlnx460ex, and boot
Waiting for PHY auto negotiation to complete... done
ENET Speed is 1000 Mbps - FULL duplex connection (EMAC0)
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
DHCP client bound to address 10.10.2.139
Using ppc_4xx_eth0 device
TFTP from server 10.10.2.51; our IP address is 10.10.2.139
Filename '/mlnx460ex/vmlinuz'.
Load address: 0x400000
Loading: #################################################################
##############################################################
done
Bytes transferred = 1862752 (1c6c60 hex)
Using ppc_4xx_eth0 device
TFTP from server 10.10.2.51; our IP address is 10.10.2.139
Filename '/mlnx460ex/fdt'.
Load address: 0x800000
Loading: #
done
Bytes transferred = 9230 (240e hex)
Using ppc_4xx_eth0 device
TFTP from server 10.10.2.51; our IP address is 10.10.2.139
Filename '/mlnx460ex/rootfs'.
Load address: 0xc00000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
####################
done
Bytes transferred = 6015766 (5bcb16 hex)
Booting mfg
## Loading init Ramdisk from Legacy Image at 00c00000 ...
Verifying Checksum ... OK
Loading Ramdisk to 2fa43000, end 2ffffad6 ... OK
Using mlnx460ex machine description
Linux version 2.6.27-MELLANOXbfuni-m460ex (root@fit15) (gcc version 4.2.2) SX_PPC_M460EX SX_3.2.0100 #1 2012-03-06 22:23:53
Found initrd at 0xefa43000:0xeffffad6
Zone PFN ranges:
DMA 0x00000000 -> 0x00030000
Normal 0x00030000 -> 0x00030000
HighMem 0x00030000 -> 0x00080000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00080000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 520192
Kernel command line: root=/dev/ram rw ramdisk_size=180224 ramdisk=262144 console=ttyS0,9600
UIC0 (32 IRQ sources) at DCR 0xc0
UIC1 (32 IRQ sources) at DCR 0xd0
UIC2 (32 IRQ sources) at DCR 0xe0
UIC3 (32 IRQ sources) at DCR 0xf0
PID hash table entries: 4096 (order: 12, 16384 bytes)
clocksource: timebase mult[400000] shift[22] registered
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2068972k/2097152k available (3700k kernel code, 27136k reserved, 136k data, 135k bss, 160k init)
SLUB: Genslabs=10, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 1998.84 BogoMIPS (lpj=3997696)
Mount-cache hash table entries: 512
net_namespace: 776 bytes
NET: Registered protocol family 16
256k L2-cache enabled
PCIE0: Checking link...
PCIE0: No device detected.
PCI host bridge /plb/pciex@d00000000 (primary) ranges:
MEM 0x0000000e00000000..0x0000000e7fffffff -> 0x0000000080000000
MEM 0x0000000f00000000..0x0000000f000fffff -> 0x0000000000000000
IO 0x0000000f80000000..0x0000000f8000ffff -> 0x0000000000000000
Removing ISA hole at 0x0000000f00000000
4xx PCI DMA offset set to 0x00000000
PCIE0: successfully set as root-complex
PCIE1: Checking link...
PCIE1: Device detected, waiting for link...
PCIE1: link is up !
PCI host bridge /plb/pciex@d20000000 (primary) ranges:
MEM 0x0000000e80000000..0x0000000effffffff -> 0x0000000080000000
MEM 0x0000000f00100000..0x0000000f001fffff -> 0x0000000000000000
IO 0x0000000f80010000..0x0000000f8001ffff -> 0x0000000000000000
Removing ISA hole at 0x0000000f00100000
4xx PCI DMA offset set to 0x00000000
PCIE1: successfully set as root-complex
PCI: Probing PCI hardware
PCI: Hiding 4xx host bridge resources 0000:40:00.0
PCI: Hiding 4xx host bridge resources 0001:80:00.0
pci 0000:40:00.0: PCI bridge, secondary bus 0000:41
pci 0000:40:00.0: IO window: disabled
pci 0000:40:00.0: MEM window: disabled
pci 0000:40:00.0: PREFETCH window: disabled
pci 0001:80:00.0: PCI bridge, secondary bus 0001:81
pci 0001:80:00.0: IO window: disabled
pci 0001:80:00.0: MEM window: 0x80000000-0x800fffff
pci 0001:80:00.0: PREFETCH window: disabled
bus: 40 index 0 io port: [fffe0000, fffeffff]
bus: 40 index 1 mmio: [e00000000, e7fffffff]
bus: 41 index 0 mmio: [fffe0000, fffe0fff]
bus: 41 index 1 mmio: [d80000000, d800fffff]
bus: 41 index 2 mmio: [d80000000, d800fffff]
bus: 41 index 3 mmio: [0, 0]
bus: 80 index 0 io port: [0, ffff]
bus: 80 index 1 mmio: [e80000000, effffffff]
bus: 81 index 0 mmio: [0, fff]
bus: 81 index 1 mmio: [e80000000, e800fffff]
bus: 81 index 2 mmio: [0, 0]
bus: 81 index 3 mmio: [0, 0]
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 5874k freed
Configuring USB GPIO 16 + 19
highmem bounce pool size: 64 pages
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 1494
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x4ef600300 (irq = 20) is a 16550A
console [ttyS0] enabled
4ef600300.serial: ttyS0 at MMIO 0x4ef600300 (irq = 20) is a 16550A
brd: module loaded
PPC 4xx OCP EMAC driver, version 3.54
MAL v2 /plb/mcmal, 2 TX channels, 16 RX channels
ZMII /plb/opb/emac-zmii@ef600d00 initialized
RGMII /plb/opb/emac-rgmii@ef601500 initialized with MDIO support
TAH /plb/opb/emac-tah@ef601350 initialized
TAH /plb/opb/emac-tah@ef601450 initialized
/plb/opb/emac-rgmii@ef601500: input 0 in RGMII mode
eth0: EMAC-0 /plb/opb/ethernet@ef600e00, MAC ef42412c
eth0: found Generic MII PHY (0x00)
/plb/opb/emac-rgmii@ef601500: input 1 in RGMII mode
eth1: EMAC-1 /plb/opb/ethernet@ef600f00, MAC ef42512c
eth1: found Generic MII PHY (0x01)
Driver 'sd' needs updating - please use bus_type methods
4ff000000.nor_flash: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Intel/Sharp Extended Query Table at 0x010A
Using buffer write method
Using auto-unlock on power-up/resume
cfi_cmdset_0001: Erase suspend on write enabled
RedBoot partition parsing not available
Creating 6 MTD partitions on "4ff000000.nor_flash":
0x00000000-0x001e0000 : "KERNEL_1"
0x001e0000-0x00200000 : "FDT_1"
0x00200000-0x003e0000 : "KERNEL_2"
0x003e0000-0x00400000 : "FDT_2"
0x00f80000-0x00fa0000 : "UBOOTENV"
0x00fa0000-0x01000000 : "UBOOT"
NAND device: Manufacturer ID: 0xec, Chip ID: 0xd3 (Samsung NAND 1GiB 3,3V 8-bit)
2 NAND chips detected
Scanning device for bad blocks
Bad eraseblock 1430 at 0x0b2c0000
Bad eraseblock 4579 at 0x23c60000
Bad eraseblock 6849 at 0x35820000
Bad eraseblock 15143 at 0x764e0000
Creating 4 MTD partitions on "4e0000000.ndfc.nand":
0x00000000-0x20000000 : "ROOT_1"
0x20000000-0x40000000 : "ROOT_2"
0x40000000-0x46400000 : "CONFIG"
0x46400000-0x7c000000 : "VAR"
ppc-of-ehci 4bffd0400.ehci: OF EHCI
ppc-of-ehci 4bffd0400.ehci: new USB bus registered, assigned bus number 1
ppc-of-ehci 4bffd0400.ehci: irq 32, io mem 0x4bffd0400
ppc-of-ehci 4bffd0400.ehci: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
ibm-iic 4ef600700.i2c: using standard (100 kHz) mode
rtc-ds1307 0-0068: rtc core: registered ds1338 as rtc0
rtc-ds1307 0-0068: 56 bytes nvram
ibm-iic 4ef600800.i2c: using standard (100 kHz) mode
hwmon-vid: Unknown VRM version of your CPU
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc-ds1307 0-0068: setting system clock to 2021-03-07 07:48:10 UTC (1615103290)
RAMDISK: Compressed image found at block 0
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 160k init
hwclock: Could not access RTC: No such file or directory
Running startup scripts.
Running /etc/init.d/rcS.d/S05hwrng
Probing for HRNG module
Mixing in entropy from HRNG
Running /etc/init.d/rcS.d/S10tms_dhcpc
Starting DHCP client on interfaces: eth0 eth1
dhcp eth0: starting
dhcp eth1: starting
dhcp eth0: obtained lease
dhcp eth0: adding address: 10.10.2.139 / 24
dhcp eth0: adding default gw: 10.10.2.1
dhcp eth0: adding domain:
dhcp eth0: adding dns: 10.10.2.1
dhcp eth1: failed to get lease
Running /etc/init.d/rcS.d/S30tms_autostart
Running /etc/init.d/rcS.d/S34automfg
-
(none) login: root
BusyBox v1.00 (2010.12.03-23:16+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
Processing /etc/profile... Done
#