Is there any chance someone might help me find the X86_64-3.10.4206-installer.bin for the sn2700 switch? Been looking all over and the switch is well out of warranty.
Mellanox Switches - Tips & Tricks
- Thread starter NablaSquaredG
- Start date
Notice: Page may contain affiliate links for which we may earn a small commission through services like Amazon Affiliates or Skimlinks.
Do you really want 4206? Here's 4606:
我有一台SN2700，现在开机系统故障灯报错（常亮红灯），然后在系统里面有报错提示，换了电源模块还是出现同样的错误，哪位能帮帮我吗？
I have a SN2700, and now the system fault light is reporting an error (red light is constantly on). There is also an error prompt in the system. I replaced the power module, but the same error still occurs. Can anyone help me? Thank you
I have a SN2700, and now the system fault light is reporting an error (red light is constantly on). There is also an error prompt in the system. I replaced the power module, but the same error still occurs. Can anyone help me? Thank you
This was a bug in an earlier Oryx version, once you upgrade the warning goes away. Which is why the person above ^ asked the verison. Make sure you running latest.
我想问一下，我有一台 SN2700，想安装最新的系统。我可以进入 BIOS，但是无论我怎么插入 U 盘，它都无法进入 U 盘安装模式。相反，它会自动进入救援模式。这是什么原因造成的？
PS：即使更换了U盘，问题仍然存在。
I have to ask, I have this sn2700 and I want to install the latest system. I can enter the BIOS, but no matter how I plug in the USB drive, it doesn't enter the USB drive installation mode. Instead, it automatically enters rescue mode. What could be the reason for this?
PS: Even after changing the USB drive, the problem persists.
The system will prompt —— discover: Rescue mode detected. Installer disabled.
PS：即使更换了U盘，问题仍然存在。
I have to ask, I have this sn2700 and I want to install the latest system. I can enter the BIOS, but no matter how I plug in the USB drive, it doesn't enter the USB drive installation mode. Instead, it automatically enters rescue mode. What could be the reason for this?
PS: Even after changing the USB drive, the problem persists.
The system will prompt —— discover: Rescue mode detected. Installer disabled.
Last edited:
And may be you even have 3.10.2202 )?
Just have found 3.10.4504. Only 3.10.2202 is needed now...
Last edited:
What is the procedure to do this? also have you tried flashing the firmware with mst?
Hello,
i have 2 mellanox sn2100 one them have a disk failure. I managed to replace the disk build an ONIE pxe boot the switch from pxe embed onie. I can download the img format of onyx from nvidia site, but i need a BIN format in order for onis-nos-intall command to work.
Can anybody help finding this BIN ?
Thx
i have 2 mellanox sn2100 one them have a disk failure. I managed to replace the disk build an ONIE pxe boot the switch from pxe embed onie. I can download the img format of onyx from nvidia site, but i need a BIN format in order for onis-nos-intall command to work.
Can anybody help finding this BIN ?
Thx
I finally managed to install X86_64-3.9.3202-installer.bin i foud but now i am stuck in loop because i used UEFI pxe boot since i don have a USB stick with mini-usb b port
. Any advice on how to break the loop will be great
Thx
For those who like me are stuck in the the update bios loop i managed to solve it by booting in onie rescue, mounting the partition where onyx is installed and rename /opt/tms/bin/bios_update.sh to .bak . This allowed the boot to skip updating bios and boot normaly.
Could you please share your onyx-X86_64-3.10.2202.img or 3.10.2102 file? Thank you very much.
Hi. Second question about 3.10.2xxx and no one answers(.
Here is 3.10.2102 that I've found: image-X86_64-3.10.2102.img
I wanted to thank the thread curator and author NablaSquaredG and nasbdh9 for the information, documentation, sw links and guidance, along with other contributors. Without your information, It would have been more difficult to resurrect my telco auction'ed SN2410 switch. My switch sustained some physical damage to the front somewhere in its life, also the mgmt board supercapacitor seems to be leaking. If anyone else needs a replacement, take a look at the attached pictures for the part number. I think the SC is responsible for keeping the mSata alive after an unintentional power loss long enough to write out its buffer.
