EU HGST 200GB SAS SSD HUSSL4020BSS600 @55EUR

Notice: Page may contain affiliate links for which we may earn a small commission through services like Amazon Affiliates or Skimlinks.
M

mmk

Active Member
Oct 15, 2016
104
39
28
Czech Republic
This is a great deal for being in Europe..I just bought two 100GB .B from US and paid a little more each after customs fees/taxes/whatever. Ugh.

Note that these have an EMC product number on the tag so they probably came from a storage array. They may have some more use because of that. Still, shouldnt really matter considering 18PB endurance..
 
M

Mirabis

Member
Mar 18, 2016
113
6
18
29
Offer of 4 x 49.62 got accepted :)

Edit; Shipping to NL is €16.50 as well.
 
Last edited:
M

mmk

Active Member
Oct 15, 2016
104
39
28
Czech Republic
My offer of 4@50e each got accepted. Same shipping rate of 16.50e to Czech as they billed a.out for Sweden.

Just couldnt help myself :p
 
R

Rand__

Well-Known Member
Mar 6, 2014
6,633
1,767
113
Well they didn't accept my 12@35€ :p not even countered. But I assume they had enough offers :)
 
M

mmk

Active Member
Oct 15, 2016
104
39
28
Czech Republic
Received my disks this week. Has anyone else been able to test theirs yet? Out of the four I got two report a SMART warning. Some output:

Code: 
== START OF INFORMATION SECTION ===
Vendor:               HITACHI
Product:              HUSRL402 CLAR200
Revision:             C140
Compliance:           SPC-4
User Capacity:        200,049,647,720 bytes [200 GB]
Logical block size:   520 bytes
Physical block size:  4160 bytes
Rotation Rate:        Solid State Device
Form Factor:          2.5 inches
Logical Unit id:      0x5000cca0131fc7f0
Serial number:        XTVKGUTA
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Jun 22 17:01:17 2017 CEST
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Disabled or Not Supported

=== START OF READ SMART DATA SECTION ===
SMART Health Status: WARNING: ascq=0x10 [asc=b, ascq=10]

Percentage used endurance indicator: 1%
Current Drive Temperature:     25 C
Drive Trip Temperature:        85 C
Is anyone familiar with that particular ascq code? I've been unable to find anything useful about what it means. Also as a side note, on the two drives that have this error it says 'blocks sent to initiator = 0' in cache info. The normally working ones have a higher there.

Otherwise the drives have very little writes considering what they are. The highest is a paltry 29TB or so. These seem to have come from some VNX and required also a format from 520 byte blocks to 512..
 
M

mmk

Active Member
Oct 15, 2016
104
39
28
Czech Republic
Thanks, good find. Doesn't sound too bad then. I guess some of the others buyers may have the same issue. Wonder if it is possible to somehow reset that warning? I've only had them behind a LSI 2308 (IT mode only) so not sure what a RAID controller would think about this..
 
S

Servoids

New Member
Jun 26, 2017
6
0
1
43
Hi
Bought some of that disk and i had problem with dell perc controllers
it shows me blocked state.
Is it possible to run them on dell servers?
 
S

Servoids

New Member
Jun 26, 2017
6
0
1
43
but how i can reformat them if controller block them? had you attached them directly to motherboard?
 
E

Emek

Member
May 14, 2017
32
6
8
I put the RAID card into HBA mode before loading CentOS.

I'm not familiar with Dell controllers only HPE.
 
You must log in or register to reply here.
Top Bottom