Fujitsu Futro S920 Thin Client as opnsense firewall
- Thread starter frauhottelmann
- Start date
Notice: Page may contain affiliate links for which we may earn a small commission through services like Amazon Affiliates or Skimlinks.
Yes, sure:
root@pve:~# lspci -vvv
Code:
root@pve:~# lspci -vvv
00:00.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 16h Processor Root Complex
DeviceName: Realtek RTL8111G
Subsystem: Fujitsu Technology Solutions Family 16h Processor Root Complex
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:01.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Kabini [Radeon HD 8330E] (prog-if 00 [VGA controller])
Subsystem: Fujitsu Technology Solutions Kabini [Radeon HD 8330E]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 47
Region 0: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 2: Memory at d0000000 (64-bit, prefetchable) [size=8M]
Region 4: I/O ports at f000 [size=256]
Region 5: Memory at feb00000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at 000c0000 [disabled] [size=128K]
Capabilities: [48] Vendor Specific Information: Len=08 <?>
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag+ RBE+ FLReset-
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
DevCap2: Completion Timeout: Not Supported, TimeoutDis- NROPrPrP- LTR-
10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- 10BitTagReq- OBFF Disabled,
AtomicOpsCtl: ReqEn-
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee02004 Data: 0025
Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
Capabilities: [270 v1] Secondary PCI Express
LnkCtl3: LnkEquIntrruptEn- PerformEqu-
LaneErrStat: 0
Kernel driver in use: radeon
Kernel modules: radeon, amdgpu
00:01.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] Kabini HDMI/DP Audio
Subsystem: Fujitsu Technology Solutions Kabini HDMI/DP Audio
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 45
Region 0: Memory at feb64000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [48] Vendor Specific Information: Len=08 <?>
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag+ RBE+ FLReset-
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
DevCap2: Completion Timeout: Not Supported, TimeoutDis- NROPrPrP- LTR-
10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- 10BitTagReq- OBFF Disabled,
AtomicOpsCtl: ReqEn-
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee08004 Data: 0024
Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:02.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 16h Processor Function 0
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:02.1 PCI bridge: Advanced Micro Devices, Inc. [AMD] Family 16h Processor Functions 5:1 (prog-if 00 [Normal decode])
Subsystem: Advanced Micro Devices, Inc. [AMD] Family 16h Processor Functions 5:1
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 25
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff [disabled] [32-bit]
Memory behind bridge: fe600000-fe8fffff [size=3M] [32-bit]
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff [disabled] [64-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0
ExtTag+ RBE+
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd- ExtTag+ PhantFunc- AuxPwr- NoSnoop+
MaxPayload 512 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s L1, Exit Latency L0s <512ns, L1 <64us
ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1
TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #0, PowerLimit 0W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState-
RootCap: CRSVisible+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible+
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR-
10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS- LN System CLS Not Supported, TPHComp- ExtTPHComp- ARIFwd-
AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis- LTR- 10BitTagReq- OBFF Disabled, ARIFwd-
AtomicOpsCtl: ReqEn- EgressBlck-
LnkCap2: Supported Link Speeds: 2.5-5GT/s, Crosslink- Retimer- 2Retimers- DRS-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis+
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance Preset/De-emphasis: -6dB de-emphasis, 0dB preshoot
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee04004 Data: 0021
Capabilities: [b0] Subsystem: Advanced Micro Devices, Inc. [AMD] Family 16h Processor Functions 5:1
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
Kernel driver in use: pcieport
00:02.2 PCI bridge: Advanced Micro Devices, Inc. [AMD] Family 16h Processor Functions 5:1 (prog-if 00 [Normal decode])
Subsystem: Advanced Micro Devices, Inc. [AMD] Family 16h Processor Functions 5:1
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 27
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: e000-efff [size=4K] [16-bit]
Memory behind bridge: fea00000-feafffff [size=1M] [32-bit]
Prefetchable memory behind bridge: d0800000-d08fffff [size=1M] [32-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag+ RBE+
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd- ExtTag+ PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <512ns, L1 <64us
ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1
TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #0, PowerLimit 0W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState-
RootCap: CRSVisible+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible+
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR-
10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS- LN System CLS Not Supported, TPHComp- ExtTPHComp- ARIFwd-
AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis- LTR- 10BitTagReq- OBFF Disabled, ARIFwd-
AtomicOpsCtl: ReqEn- EgressBlck-
LnkCap2: Supported Link Speeds: 2.5-5GT/s, Crosslink- Retimer- 2Retimers- DRS-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis+
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance Preset/De-emphasis: -6dB de-emphasis, 0dB preshoot
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee08004 Data: 0021
Capabilities: [b0] Subsystem: Advanced Micro Devices, Inc. [AMD] Family 16h Processor Functions 5:1
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
Kernel driver in use: pcieport
00:02.5 PCI bridge: Advanced Micro Devices, Inc. [AMD] Family 16h Processor Functions 5:1 (prog-if 00 [Normal decode])
Subsystem: Advanced Micro Devices, Inc. [AMD] Family 16h Processor Functions 5:1
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 28
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: d000-dfff [size=4K] [16-bit]
Memory behind bridge: fe900000-fe9fffff [size=1M] [32-bit]
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff [disabled] [64-bit]
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- VGA16+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0
ExtTag+ RBE+
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd- ExtTag+ PhantFunc- AuxPwr- NoSnoop+
MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
LnkCap: Port #4, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <512ns, L1 <64us
ClockPM- Surprise- LLActRep+ BwNot+ ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1
TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #0, PowerLimit 0W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState-
RootCap: CRSVisible+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible+
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR-
10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS- LN System CLS Not Supported, TPHComp- ExtTPHComp- ARIFwd-
AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis- LTR- 10BitTagReq- OBFF Disabled, ARIFwd-
AtomicOpsCtl: ReqEn- EgressBlck-
LnkCap2: Supported Link Speeds: 2.5-5GT/s, Crosslink- Retimer- 2Retimers- DRS-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis+
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance Preset/De-emphasis: -6dB de-emphasis, 0dB preshoot
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee01004 Data: 0021
Capabilities: [b0] Subsystem: Advanced Micro Devices, Inc. [AMD] Family 16h Processor Functions 5:1
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
Kernel driver in use: pcieport
00:10.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller (rev 01) (prog-if 30 [XHCI])
Subsystem: Fujitsu Technology Solutions FCH USB XHCI Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at feb68000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [90] MSI-X: Enable+ Count=8 Masked-
Vector table: BAR=0 offset=00001000
PBA: BAR=0 offset=00001080
Capabilities: [a0] Express (v2) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0
ExtTag- RBE+ FLReset-
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+ NROPrPrP- LTR+
10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- 10BitTagReq- OBFF Disabled,
AtomicOpsCtl: ReqEn-
Capabilities: [100 v1] Latency Tolerance Reporting
Max snoop latency: 0ns
Max no snoop latency: 0ns
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
00:11.0 SATA controller: Advanced Micro Devices, Inc. [AMD] FCH SATA Controller [AHCI mode] (rev 40) (prog-if 01 [AHCI 1.0])
Subsystem: Fujitsu Technology Solutions FCH SATA Controller [AHCI mode]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 29
Region 0: I/O ports at f140 [size=8]
Region 1: I/O ports at f130 [size=4]
Region 2: I/O ports at f120 [size=8]
Region 3: I/O ports at f110 [size=4]
Region 4: I/O ports at f100 [size=16]
Region 5: Memory at feb6e000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [60] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] SATA HBA v1.0 InCfgSpace
Capabilities: [50] MSI: Enable+ Count=1/8 Maskable- 64bit+
Address: 00000000fee04004 Data: 0022
Capabilities: [d0] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ahci
Kernel modules: ahci
00:12.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 39) (prog-if 10 [OHCI])
Subsystem: Fujitsu Technology Solutions FCH USB OHCI Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at feb6d000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
Kernel modules: ohci_pci
00:12.2 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 39) (prog-if 20 [EHCI])
Subsystem: Fujitsu Technology Solutions FCH USB EHCI Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at feb6c000 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3-
Capabilities: [e4] Debug port: BAR=1 offset=00e0
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:13.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller (rev 39) (prog-if 10 [OHCI])
Subsystem: Fujitsu Technology Solutions FCH USB OHCI Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at feb6b000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
Kernel modules: ohci_pci
00:13.2 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller (rev 39) (prog-if 20 [EHCI])
Subsystem: Fujitsu Technology Solutions FCH USB EHCI Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at feb6a000 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3-
Capabilities: [e4] Debug port: BAR=1 offset=00e0
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:14.0 SMBus: Advanced Micro Devices, Inc. [AMD] FCH SMBus Controller (rev 3a)
Subsystem: Fujitsu Technology Solutions FCH SMBus Controller
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel driver in use: piix4_smbus
Kernel modules: i2c_piix4, sp5100_tco
00:14.2 Audio device: Advanced Micro Devices, Inc. [AMD] FCH Azalia Controller (rev 02)
Subsystem: Fujitsu Technology Solutions FCH Azalia Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at feb60000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:14.3 ISA bridge: Advanced Micro Devices, Inc. [AMD] FCH LPC Bridge (rev 11)
Subsystem: Fujitsu Technology Solutions FCH LPC Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 16h Processor Function 0
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 16h Processor Function 1
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 16h Processor Function 2
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 16h Processor Function 3
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [f0] Secure device <?>
Kernel driver in use: k10temp
Kernel modules: k10temp
00:18.4 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 16h Processor Function 4
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel driver in use: fam15h_power
Kernel modules: fam15h_power
00:18.5 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 16h Processor Function 5
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
01:00.0 Ethernet controller: Intel Corporation Ethernet Controller I225-V (rev 03)
Subsystem: Intel Corporation Ethernet Controller I225-V
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 30
Region 0: Memory at fe700000 (32-bit, non-prefetchable) [size=1M]
Region 3: Memory at fe800000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at fe600000 [disabled] [size=1M]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [70] MSI-X: Enable+ Count=5 Masked-
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
Capabilities: [a0] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ SlotPowerLimit 0W
DevCtl: CorrErr+ NonFatalErr+ FatalErr+ UnsupReq+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
MaxPayload 512 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L1, Exit Latency L1 <16us
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (downgraded), Width x1
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR+
10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS- TPHComp- ExtTPHComp-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- 10BitTagReq- OBFF Disabled,
AtomicOpsCtl: ReqEn-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance Preset/De-emphasis: -6dB de-emphasis, 0dB preshoot
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [100 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Capabilities: [140 v1] Device Serial Number 88-c9-b3-ff-ff-b5-14-91
Capabilities: [1c0 v1] Latency Tolerance Reporting
Max snoop latency: 0ns
Max no snoop latency: 0ns
Capabilities: [1f0 v1] Precision Time Measurement
PTMCap: Requester:+ Responder:- Root:-
PTMClockGranularity: 4ns
PTMControl: Enabled:- RootSelected:-
PTMEffectiveGranularity: Unknown
Capabilities: [1e0 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2- PCI-PM_L1.1+ ASPM_L1.2- ASPM_L1.1+ L1_PM_Substates+
L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
L1SubCtl2:
Kernel driver in use: igc
Kernel modules: igc
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 0c)
Subsystem: Fujitsu Technology Solutions RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 24
Region 0: I/O ports at e000 [size=256]
Region 2: Memory at fea00000 (64-bit, non-prefetchable) [size=4K]
Region 4: Memory at d0800000 (64-bit, prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v2) Endpoint, MSI 01
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0W
DevCtl: CorrErr+ NonFatalErr+ FatalErr+ UnsupReq+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR+
10BitTagComp- 10BitTagReq- OBFF Via message/WAKE#, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS- TPHComp- ExtTPHComp-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- 10BitTagReq- OBFF Disabled,
AtomicOpsCtl: ReqEn-
LnkCap2: Supported Link Speeds: 2.5GT/s, Crosslink- Retimer- 2Retimers- DRS-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance Preset/De-emphasis: -6dB de-emphasis, 0dB preshoot
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [b0] MSI-X: Enable+ Count=4 Masked-
Vector table: BAR=4 offset=00000000
PBA: BAR=4 offset=00000800
Capabilities: [d0] Vital Product Data
pcilib: sysfs_read_vpd: read failed: No such device
Not readable
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Capabilities: [140 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
Capabilities: [160 v1] Device Serial Number 01-00-00-00-00-00-00-01
Capabilities: [170 v1] Latency Tolerance Reporting
Max snoop latency: 0ns
Max no snoop latency: 0ns
Kernel driver in use: r8169
Kernel modules: r8169
03:00.0 SATA controller: ASMedia Technology Inc. ASM1062 Serial ATA Controller (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: ASMedia Technology Inc. ASM1062 Serial ATA Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 32
Region 0: I/O ports at d050 [size=8]
Region 1: I/O ports at d040 [size=4]
Region 2: I/O ports at d030 [size=8]
Region 3: I/O ports at d020 [size=4]
Region 4: I/O ports at d000 [size=32]
Region 5: Memory at fe910000 (32-bit, non-prefetchable) [size=512]
Expansion ROM at fe900000 [disabled] [size=64K]
Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee01004 Data: 0022
Capabilities: [78] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM not supported
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (downgraded), Width x1
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABC, TimeoutDis+ NROPrPrP- LTR-
10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- 10BitTagReq- OBFF Disabled,
AtomicOpsCtl: ReqEn-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance Preset/De-emphasis: -6dB de-emphasis, 0dB preshoot
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete- EqualizationPhase1-
EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
Kernel driver in use: ahci
Kernel modules: ahciyeah, you're running PCIe Gen 1. You should really try to enable PCIe Gen2 using the FreeDOS/editcmos workflow
I succeeded! now I reach these speeds
Code:
Speedtest by Ookla
Server: Vodafone IT - Milan (id: 4302)
ISP: Telecom Italia
Idle Latency: 11.34 ms (jitter: 0.81ms, low: 10.90ms, high: 12.19ms)
Download: 2156.85 Mbps (data used: 2.4 GB)
37.78 ms (jitter: 33.07ms, low: 9.85ms, high: 335.34ms)
Upload: 1029.52 Mbps (data used: 998.2 MB)
23.81 ms (jitter: 1.74ms, low: 10.82ms, high: 36.42ms)
Packet Loss: 0.0%Nice! and how is CPU utilization?
Does the connection use PPPoE btw.?
Does the connection use PPPoE btw.?
Seems to handle everything smoothly, yes I use PPPoE on the Zyxel router
I don't use Futro as a router, I can't do the test sorry.
If anyone needs it I have summarized all the steps of the Editcmox procedure at this link
OK just for the fun of it...
First of all, thank you all for the support so far.
I managed to update the BIOS and enable Gen2 PCIe (thx again).
So for what its worth, I found the overview of the Codes on for the D3133-S board (most of them align with what I tested so far)
The items marked as " <-- Not part of my DUMP" were not found in my backup based on my BIOS but might also be unvisible as some were not activated in my BIOS. So YMMV..
Items marked as "TBD" were in my BIOS dump but not to be found in the D3313-S List
Kontron page for D3313-S Motherboards:
Motherboard Manual
Main Entry for the Kontron FTP:
Enjoy lurking around and searching around.
First of all, thank you all for the support so far.
I managed to update the BIOS and enable Gen2 PCIe (thx again).
So for what its worth, I found the overview of the Codes on for the D3133-S board (most of them align with what I tested so far)
Code:
0x0001 SerialPort
0x0003 ParallelPort
0x0007 LAN
0x000b USBLegacySupport
0x000d LANRemoteBoot
0x0010 FlashWrite
0x0011 WakeupLAN
0x0013 OnAutomaticWakeupm
0x0014 SerialPort2
0x0019 SATAController
0x001a PasswordOnBoot
0x001b ForceLANBoot
0x0020 TBD?
0x0024 Numlock
0x003d WakeuponUSB
0x0042 FANControl
0x0045 SMBIOSEventLogging
0x0048 BootfromRemovableMedia
0x0049 PasswordEntryonBootforHDD
0x0050 WakeuponRTC
0x0051 DayofWakeuponRTC
0x0052 HourofWakuponRTC <-- Not part of my DUMP
0x0053 MinuteofWakeuponRTC <-- Not part of my DUMP
0x0054 SecondofWakeuponRTC <-- Not part of my DUMP
0x0055 FastBoot
0x0056 AudioController
0x005c SecurityChip
0x005d ChangeTPMState
0x007f PowerFailureRecovery
0x0080 QuietBoot
0x0081 LowPowerSoftOff
0x0082 TpmSkipPPI
0x0087 SATAControllerModeSelection
0x008a EraseEventLog
0x008d VirusWarning
0x008e CabinetMonitoring
0x009a PendingTPMOperation
0x00a5 PowerLedS3Blinking
0x00ad HibernateLikeSoftOff
0x00ae UsbAtPowerOff
0x00af PostErrors
0x00b1 PerrGeneration
0x00b2 SerrGeneration
0x00b3 Lan2 <-- Not part of my DUMP
0x00b5 BootWatchdogTimeout <-- Not part of my DUMP
0x00b7 SkipUsb <-- Not part of my DUMP
0x00b8 SkipPs2
0x00ba Fan2Wiring
0x00bb Fan3Wiring <-- Not part of my DUMP
0x00c5 UsbPortControl
0x00c6 UsbDeviceControl
0x00c7 LvdsPanelConfigSelect
0x00c8 NonEDIDSupport
0x00c9 LvdsMode <-- Not part of my DUMP
0x00ca LvdsChannelSwap <-- Not part of my DUMP
0x00cb LvdsBacklightEnablePolarity <-- Not part of my DUMP
0x00cc LvdsBrightness <-- Not part of my DUMP
0x00cd PostScreenMode <-- Not part of my DUMP
0x00ce FrontPanelAudio <-- Not part of my DUMP
0x00cf PreferUsbBoot <-- Not part of my DUMP
0x00d3 UsbTransferTimeOut
0x00D4 TBD??
0x00d7 PrimaryDisplay
0x00d8 InternalGraphics
0x00e2 AspmSupport <-- Not part of my DUMP
0x00e5 NetworkStack
0x00e6 Ipv4PxeSupport
0x00e7 Ipv6PxeSupport
0x00e8 SecureBoot
0x00e9 DefaultKeyProvisioning
0x00ea Csm
0x00ff PowerOnSource
0x0101 Above4GDecoding
0x0103 BootOptionFilter
0x0104 LaunchPxeOpRomPolicy
0x0105 LaunchStorageOpRomPolicy
0x0106 LaunchVideoOpRomPolicy
0x0107 OtherPciDeviceRomPriority
0x010e TermsOfUse
0x0110 ServerIpAddress
0x0111 SilentUpdate
0x0112 ManuallyCheckForUpdate <-- Not part of my DUMP
0x013a LvdsSupport <-- Not part of my DUMP
0x013b LvdsBrightnessCtrl <-- Not part of my DUMP
0x013e Dash <-- Not part of my DUMP
0x013f SerialPort3
0x014f UpdateServerAddress
0x015b mSataSupport
0x0170 AutomaticBiosUpdate
0x01b7 FjSetupIdPsppPolicy
0x01b8 FjSetupIdSmartSelfTest
0x01fb FjSetupIdWakeUpMode
0x01fc FjSetupIdWakeUpModeWeeklySunday
0x01fd FjSetupIdWakeUpModeWeeklyMonday
0x01fe FjSetupIdWakeUpModeWeeklyTuesday
0x01ff FjSetupIdWakeUpModeWeeklyWednesday
0x0200 FjSetupIdWakeUpModeWeeklyThursday
0x0201 FjSetupIdWakeUpModeWeeklyFriday
0x0202 FjSetupIdWakeUpModeWeeklySaturday
0x0203 FjSetupIdRemoveInvalidBootOptions <-- Not part of my DUMPItems marked as "TBD" were in my BIOS dump but not to be found in the D3313-S List
Kontron page for D3313-S Motherboards:
Motherboard Manual
Main Entry for the Kontron FTP:
Enjoy lurking around and searching around.
Last edited:
OK now I have a small question to all PROXMOX users on the S920.
I have a setup of a 3-node cluster (all S920) and when I transfer data between the clusters (e.g. via SSH or NFS or CIFS), the speeds are okayish, but when I do a backup via proxmox I get sub-stelar speeeds of around 16-19MiB/s (not dependent whether I save it on a SATA or mSATA device or even USB.
When I back it up to my RasPi 3 with attached USB HDD I get speeds of around 30-40mMiB/s
My assumption is that it is bottlenecked by the CPU.
Here are my test results:
FIO
fio to SMB share: 155MiB/s-155MiB/s
fio to local mSATA: 93.7MiB/s-93.7MiB/s
scp from node1 to node3 internal SSD: 66.7MB/s
iperf2 shows 2.1 and 1.9 GBit/s (in dualtest)
iperf3 seems to do something different and in bidir test and is kind of asynchronous
Proxmox Backup to node3 (via SMB): 19MiB/s
My assumption is: When doing a proxmox backup it opens a file handle (tar) which will be filled from the sending machine. The problem might be that this file handle is a tar file and the sender needs to tar the VM/LXC which might be the bottle neck for the backup.
I also tested it with a i3-6100T node and this gave me a backup of around 75MiB/s
Any ideas on how to improve this backup process?
I have a setup of a 3-node cluster (all S920) and when I transfer data between the clusters (e.g. via SSH or NFS or CIFS), the speeds are okayish, but when I do a backup via proxmox I get sub-stelar speeeds of around 16-19MiB/s (not dependent whether I save it on a SATA or mSATA device or even USB.
When I back it up to my RasPi 3 with attached USB HDD I get speeds of around 30-40mMiB/s
My assumption is that it is bottlenecked by the CPU.
Here are my test results:
FIO
Code:
fio --ioengine=libaio --direct=1 --name=test --filename=test --bs=4m --iodepth=64 --size=5G --readwrite=writefio to local mSATA: 93.7MiB/s-93.7MiB/s
scp from node1 to node3 internal SSD: 66.7MB/s
iperf2 shows 2.1 and 1.9 GBit/s (in dualtest)
Code:
[ 1] 0.0000-10.0047 sec 2.45 GBytes 2.10 Gbits/sec
[ *2] 0.0000-10.0176 sec 2.23 GBytes 1.91 Gbits/sec
[SUM] 0.0000-10.0074 sec 4.68 GBytes 4.02 Gbits/sec
Code:
[ ID][Role] Interval Transfer Bitrate Retr
[ 5][TX-C] 0.00-10.00 sec 292 MBytes 245 Mbits/sec 0 sender
[ 5][TX-C] 0.00-10.00 sec 285 MBytes 239 Mbits/sec receiver
[ 7][RX-C] 0.00-10.00 sec 2.62 GBytes 2.25 Gbits/sec 0 sender
[ 7][RX-C] 0.00-10.00 sec 2.62 GBytes 2.25 Gbits/sec receiver
Code:
INFO: starting new backup job: vzdump 101 --compress zstd --node node1 --mode snapshot --notes-template '{{guestname}}' --notification-mode auto --storage SMB_USB2TB --remove 0
INFO: Starting Backup of VM 101 (lxc)
INFO: Backup started at 2024-04-18 18:32:58
INFO: status = running
INFO: CT Name: mqtt
INFO: including mount point rootfs ('/') in backup
INFO: backup mode: snapshot
INFO: ionice priority: 7
INFO: create storage snapshot 'vzdump'
INFO: creating vzdump archive '/mnt/pve/SMB_USB2TB/dump/vzdump-lxc-101-2024_04_18-18_32_58.tar.zst'
INFO: Total bytes written: 779622400 (744MiB, 19MiB/s)My assumption is: When doing a proxmox backup it opens a file handle (tar) which will be filled from the sending machine. The problem might be that this file handle is a tar file and the sender needs to tar the VM/LXC which might be the bottle neck for the backup.
I also tested it with a i3-6100T node and this gave me a backup of around 75MiB/s
Any ideas on how to improve this backup process?
Last edited:
Thx for the tip, I will have a look into how proxmox performs the backups. maybe there is a possibility to "change " the way vzdump works. "maybe"
Hello everyone,
Shouldn't the EditCMOS.exe workflow to enable PCIe 2.0 on the Futro S920 be
I've seen it quoted in many places on this forum and in a user's blog as
Shouldn't the EditCMOS.exe workflow to enable PCIe 2.0 on the Futro S920 be
EditCMOS.exe SetID:0x01B7=0x151 ?I've seen it quoted in many places on this forum and in a user's blog as
EditCMOS.exe SetID:0x01B7=0x0151, but I got errors when I tried that command. The only time it worked for me was when I used EditCMOS.exe SetID:0x01B7=0x151.@neuralreticulator
Hello! o) I'm not sure, when I tried to enable PCI-Gen2 mode recently, I was not able to find/download the binaries anymore. o( The only thing that was available and seemingly worked was the GUI based windows BIOS settings tool from Fujitsu. This has an option to be clicked for PCI-Gen2 mode, kind of easy, but it seemed to me, it also sets some other settings, which I wasn't a fan of, since the Futro was using a little bit more power since then. My feeling was, that it's not related to the activated PCI-Gen2 mode, but not sure, because "how to find out?". The BIOS settings tool always sets a bunch of things in one go. If I remember correctly, even after reverting back to PCI-Gen1 mode, the power consumption was higher. We are talking 10%.. not a dealbreaker, but I surely would have preferred to use the DOS tool, to just toggle the single PCI-Gen setting, to not mess with any other setting unnecessarily.
So, I can't really tell or confirm your findings yet, but these HEX code are irritating for sure, I also found the names or IDs for the PCI-Gen setting were different, wrong, not available etc.. I also had problems with these in some way. I was happy to have spotted the option in the GUI tool eventually, but as said, that was not what I wanted to use in the first place.
I would like to try again with the DOS tool, where did you download it? Can you post a working link?
Did you verify the PCI-Gen2 speed?
At least I can tell, using the BIOS GUI tool works, the speed of the NVME drive I connected to the mini PCI slot with an adapter was twice as fast afterwards (and still way below what it was capable of, but that was to be expected o). And I tried all this with the Futro S720, if that makes a difference, I guess it does not.
Hello! o) I'm not sure, when I tried to enable PCI-Gen2 mode recently, I was not able to find/download the binaries anymore. o( The only thing that was available and seemingly worked was the GUI based windows BIOS settings tool from Fujitsu. This has an option to be clicked for PCI-Gen2 mode, kind of easy, but it seemed to me, it also sets some other settings, which I wasn't a fan of, since the Futro was using a little bit more power since then. My feeling was, that it's not related to the activated PCI-Gen2 mode, but not sure, because "how to find out?". The BIOS settings tool always sets a bunch of things in one go. If I remember correctly, even after reverting back to PCI-Gen1 mode, the power consumption was higher. We are talking 10%.. not a dealbreaker, but I surely would have preferred to use the DOS tool, to just toggle the single PCI-Gen setting, to not mess with any other setting unnecessarily.
So, I can't really tell or confirm your findings yet, but these HEX code are irritating for sure, I also found the names or IDs for the PCI-Gen setting were different, wrong, not available etc.. I also had problems with these in some way. I was happy to have spotted the option in the GUI tool eventually, but as said, that was not what I wanted to use in the first place.
I would like to try again with the DOS tool, where did you download it? Can you post a working link?
Did you verify the PCI-Gen2 speed?
At least I can tell, using the BIOS GUI tool works, the speed of the NVME drive I connected to the mini PCI slot with an adapter was twice as fast afterwards (and still way below what it was capable of, but that was to be expected o). And I tried all this with the Futro S720, if that makes a difference, I guess it does not.
You make me wonder but I seem to have used this command:
EditCMOS.exe SetID:0x01B7=0x0151
Have you updated to the latest BIOS version?
Proton Drive
Securely store, share, and access your important files and photos. Anytime, anywhere.
Here is the link to editcmos for you
GM I recently also tried using a PCIe to NVME adapter on the activated PCIe port and it worked. But it added a PCIe device in front of the two NICs which in return changed the network names in proxmox... Duhhh... And all networks suddenly did not work anymore. Had to connectto the console and fix it.
Then I saw that the adapter drew around 2-3 watts in idle and the speed... Well lets call it okay-ish. Itwas not that faster than the SSD via sata which in return did not justify the power increase in idle mode (9+vs 6+ watts). I added a screenshot with the differences. The orange line was the teston node1.
Overall I am very happy with my tripple node S920 Cluster. It draws around 25-30watts in total (incl. 3x S920, 3x 2.5GBit NICs via minipcie, 1x 5port 1GBit switch and 1x 8port 2.5GBit switch).
Although the cluster runs like totally flawless, and the VMs and Cotainers are working like a charm, I can not figure out why the backups are so slow.
Inter-node communication works over 2.5GBit and iperf3show solid 1.9-2.2GBit rates, the backups (ZSTD) report roughly 11-20MB/s (which is in parallel, so should be around 40-60MB/s which is not half the speed of 1GBit). I think this is due to CPU bottlenecks during backups.
But hey.. It is a super cheap and capable little machine, works like a horse, sips power like acolibri and transports everything like an elephant.
I have onenode with a PBS vm and one for file storage (CIFS&NFS) both with 2GB SSDs as passed through SSD.
So my advice is, get the quadcofeversions if you want something fanless, capable that does its work completely unnotived and gives you enough headroom for tinkering
Attachments
Thank you Pietro395, sorry for responding so late, I did not see your reply until now!Here is the link to editcmos for youProton Drive
Securely store, share, and access your important files and photos. Anytime, anywhere.drive.proton.me
Well I replaced my S920 with the 415 CPU with a S930 (424CC CPU). This led to approximately 2-3W more powerdraw in "idle". Before it was around 5-7W and now it ia around 8-10W.
To reduce powerdraw I use amdctl with the following script. (you have to add the other states for s930 as it does not stop at id4 instead it stops at id7
amdctl_script.sh
Code:
#!/bin/bash
echo on > /sys/module/msr/parameters/allow_writes
amdctl -m -p0 -v86
amdctl -m -p1 -v88
amdctl -m -p2 -v92
amdctl -m -p3 -v96
amdctl -m -p4 -v102
Code:
Core 3 | P-State Limits (non-turbo): Highest: 5 ; Lowest 8 | Current P-State: 5
Pstate Status CpuFid CpuDid CpuVid CpuMult CpuFreq CpuVolt IddVal IddDiv CpuCurr CpuPower
0 1 8 0 24 12.00x 2400.00MHz 1250mV 56 10 5.60A 7.00W
1 1 6 0 40 11.00x 2200.00MHz 1050mV 44 10 4.40A 4.62W
2 1 4 0 56 10.00x 2000.00MHz 850mV 34 10 3.40A 2.89W
3 1 2 0 70 9.00x 1800.00MHz 675mV 28 10 2.80A 1.89W
4 1 0 0 84 8.00x 1600.00MHz 500mV 225 100 2.25A 1.12W
5 1 12 1 94 7.00x 1400.00MHz 375mV 185 100 1.85A 0.69W
6 1 8 1 104 6.00x 1200.00MHz 250mV 150 100 1.50A 0.38W
7 1 4 1 112 5.00x 1000.00MHz 150mV 122 100 1.22A 0.18W
current 1 4 1 112 5.00x 1000.00MHz 150mVBtw this update fixed my backup speed issue a little bit. It now runs with 33MB/s so the CPU seems to bottleneck it alot