For Sale - HP C7000 Bladecenter w/ BL465/685 G7 blades & Operton 6276 cpus

Notice: Page may contain affiliate links for which we may earn a small commission through services like Amazon Affiliates or Skimlinks.

evosmash

Member
May 31, 2017
33
5
8
38
I have for sale HP C7000 Bladecenters with BL465 G7 and BL685 G7 blades. These blades have AMD Opteron 6174 chips installed however I have AMD Opteron 6276 chips for these blades included. There is no ram or hard drives.

A bit more info. I have 16 of these chassis, I have enough blades to fill about 10 of the chassis. Chassis come stocked with everything they need to run. I have 303 6200 series chips to go with these 10 chassis of blades.

6200 series count:

6282 - 6
6276 - 207
6274 - 34
6272 - 2
6238 - 14
6234 - 38
6220 - 2

I have a bit of ram but its not much so ill just throw it in and there are no hard drives. Selling full Bladecenters cheap. Hit me up and make an offer
 
  • Like
Reactions: Samir

evosmash

Member
May 31, 2017
33
5
8
38
Please post a price according to the forum rules.
My apologies! I am not sure how to price this as its an array of products in multiple configurations so its more of what someone would want.

Ill price the lot (chips and bladecenters) at 8000.00 usd o.b.o.
 
Last edited:
  • Like
Reactions: Samir

evosmash

Member
May 31, 2017
33
5
8
38
What kind of networking modules are included, if any, in the blades and c7000s?

Most if not all of the c7000 chassis have both the 1gb pass thru cards and 4gb fiber cards.
Most of the BL685 blades have HP Qlogic QMH2562 8GB Fibre Channel Host Bus Adapter 451871-B21 455869-001 451872-001
 

Attachments

  • Like
Reactions: Samir

aldo

New Member
Feb 4, 2020
5
4
3
Hello! First of all, where are you located? I'm based in Europe and if you're not here on the continent, the postage would be pretty hefty for these kinds of equipment. Secondly, if you're based in EU, I'd be interested in a chassis with 4 blades + whatever is needed to run and network them (Switch, PSU, other networking modules), so what would be the price for the setup.

Thx!
 

evosmash

Member
May 31, 2017
33
5
8
38
I am in the US, my apologies I should have mentioned this. Shipping would be quite hefty, a bit too much id reluctantly say...
 

aldo

New Member
Feb 4, 2020
5
4
3
Goddamit!

Well, good luck with the sale and may the lucky few who get their hands on the hardware have their electricity bills as low as they can be.
 
  • Like
Reactions: Wasmachineman_NL

evosmash

Member
May 31, 2017
33
5
8
38
Goddamit!

Well, good luck with the sale and may the lucky few who get their hands on the hardware have their electricity bills as low as they can be.
Thank you sir. I am letting these go for peanuts so I am hoping someone will snatch them up
 

macrules34

Active Member
Mar 18, 2016
407
28
28
40
Is the equipment boxed and ready to be shipped? Will it need to be picked up at your location and then shipped? Is this equipment at a location with a standard loading dock?
 

evosmash

Member
May 31, 2017
33
5
8
38
Is the equipment boxed and ready to be shipped? Will it need to be picked up at your location and then shipped? Is this equipment at a location with a standard loading dock?

The equipment is on pallets wrapped in plastic. There is 1 of 4 pallets I need to get wrapped back up. This equipment is at a storage unit, there is no loading dock. The equipment does not need to be picked up and shipped from elsewhere unless that is what you want to do, it can be shipped from the storage unit.



Let me know if you have any other questions.