An He10 (HUH721010AL4204) I purchased via eBay spins up but is not detected by my Adaptec ASR72405 but is detected by a SAS3008. The activity light stays lit but is in a repeating pattern of blinks where the duty cycle is ~1.75s on, 0.25s off. I have a bunch of identical drives so I know my systems tolerate them well.
This is what I get from smartctl:
I get this from sginfo:
DOA or could it be in some funky OEM mode?
This is what I get from smartctl:
Code:
=== START OF INFORMATION SECTION ===
Vendor: HGST
Product: HUH721010AL4204
Revision: C386
Compliance: SPC-4
LU is fully provisioned
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Logical Unit id: 0x5000cca2512c####
Serial number: 7PGT####
Device type: disk
Transport protocol: SAS (SPL-3)
Local Time is: Fri Oct 23 18:57:03 2020 EDT
device is NOT READY (e.g. spun down, busy)
A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options.
Code:
# sginfo -a /dev/sdh
INQUIRY response (cmd: 0x12)
----------------------------
Device Type 0
Vendor: HGST
Product: HUH721010AL4204
Revision level: C386
Serial Number ' 7PGT####'
Read-Write Error Recovery mode page (0x1)
-----------------------------------------
AWRE 1
ARRE 1
TB 0
RC 0
EER 0
PER 0
DTE 0
DCR 0
Read Retry Count 1
Correction Span 0
Head Offset Count 0
Data Strobe Offset Count 0
Write Retry Count 1
Recovery Time Limit (ms) 0
Disconnect-Reconnect mode page (0x2)
------------------------------------
Buffer full ratio 0
Buffer empty ratio 0
Bus Inactivity Limit (SAS: 100us) 0
Disconnect Time Limit 0
Connect Time Limit (SAS: 100us) 0
Maximum Burst Size 160
EMDP 0
Fair Arbitration (fcp:faa,fab,fac) 0
DIMM 0
DTDC 0
First Burst Size 0
Format Device mode page (0x3)
-----------------------------
Tracks per Zone 65535
Alternate sectors per zone 0
Alternate tracks per zone 0
Alternate tracks per lu 0
Sectors per track 1404
Data bytes per physical sector 512
Interleave 1
Track skew factor 0
Cylinder skew factor 0
Supports Soft Sectoring 0
Supports Hard Sectoring 1
Removable Medium 0
Surface 0
Rigid Disk Geometry mode page (0x4)
-----------------------------------
Number of cylinders 437400
Number of heads 14
Starting cyl. write precomp 0
Starting cyl. reduced current 0
Device step rate 0
Landing Zone Cylinder 0
RPL 0
Rotational Offset 0
Rotational Rate 7200
Verify Error Recovery mode page (0x7)
-------------------------------------
EER 0
PER 0
DTE 0
DCR 0
Verify Retry Count 1
Verify Correction Span (bits) 0
Verify Recovery Time Limit (ms) 0
Caching mode page (0x8)
-----------------------
Initiator Control 0
ABPF 0
CAP 0
DISC 0
SIZE 0
Write Cache Enabled 1
MF 0
Read Cache Disabled 0
Demand Read Retention Priority 0
Demand Write Retention Priority 0
Disable Pre-fetch Transfer Length 65535
Minimum Pre-fetch 0
Maximum Pre-fetch 65535
Maximum Pre-fetch Ceiling 65535
FSW 0
LBCSS 0
DRA 0
NV_DIS 0
Number of Cache Segments 8
Cache Segment size 0
Non-Cache Segment size 0
Control mode page (0xa)
-----------------------
TST 0
TMF_ONLY 0
D_SENSE 1
GLTSD 0
RLEC 0
Queue Algorithm Modifier 0
QErr 0
DQue [obsolete] 0
TAS 0
RAC 0
UA_INTLCK_CTRL 0
SWP 0
RAERP [obs.] 0
UAAERP [obs.] 0
EAERP [obs.] 0
ATO 0
TAS 0
AUTOLOAD MODE 0
Ready AER Holdoff Period [obs.] 0
Busy Timeout Period 0
Extended self-test completion time 65535
Notch and Partition mode page (0xc)
-----------------------------------
Notched Drive 1
Logical or Physical Notch 0
Max # of notches 40
Active Notch 0
Starting Boundary 0x0
Ending Boundary 0x6ac9800
Pages Notched 00000000 0000100c
SAS logical unit mode page (0x18)
----------------------------------------------------
Transport Layer Retries 0
SAS SSP port control mode page (0x19)
-------------------------------------
Ready LED meaning 0
I_T Nexus Loss time 2000
Initiator response time-out 2000
Power Condition mode page (0x1a)
--------------------------------
Idle 1
Standby 0
Idle Condition counter (100ms) 20
Standby Condition counter (100ms) 0
Informational Exceptions mode page (0x1c)
-----------------------------------------
PERF 0
EBF 0
EWASC 1
DEXCPT 0
TEST 0
EBACKERR 0
LOGERR 0
MRIE 3
Interval Timer 0
Report Count 0
mode page: 0x00 [Vendor (non-page format)]
---------------
0x00 0x80
0x01 0x0e
0x02 0x00
0x03 0x00
0x04 0x00
0x05 0x02
0x06 0x00
0x07 0x00
0x08 0x00
0x09 0x00
0x0a 0x00
0x0b 0x30
0x0c 0x16
0x0d 0x14
0x0e 0x00
0x0f 0x00