Starting kernel ...
booting with 4.4 kernel
NAND Type: Micron NAND 2GiB (x 1)
PLATFORM MN
dd cmd: UBI
ubi0 error: ubi_io_read: error -74 (ECC error) while reading 1040384 bytes from PEB 841:8192, read 1040384 bytes
UBIFS error (ubi0:0 pid 565): ubifs_recover_leb: corruption -3
UBIFS error (ubi0:0 pid 565): ubifs_check_node: bad node length 263218
UBIFS error (ubi0:0 pid 565): ubifs_check_node: bad node at LEB 1134:884736
magic 0x6101831
crc 0x87f8e43e
node_type 1 (data node)
group_type 128 (unknown)
sqnum 1378685144455
len 263218
key (4194457, xentry, 0x00205e)
size 335548416
compr_typ 1344
data size 263170
data:
00000000: d6 c1 c7 35 d4 a1 e1 f2 c1 d0 ef 02 7e 99 b9 63 4f 17 43 76 22 8a 8d f7 1e d1 49 19 d3 0b a3 60
[trimmed]
00025fa0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
{ bunch of stack trace stuff }
Segmentation fault
Mounting Config partition failed, non-recoverable file system corruption
Reformatting the flash, please download config and keys again ...
ubidetach: error!: cannot detach mtd2
error 16 (Device or resource busy)
ubiformat: error!: please, first detach mtd2 (/dev/mtd2) from ubi0
Formatting Doneubi0 error: ubi_attach_mtd_dev: mtd2 is already attached to ubi0
ubiattach: error!: cannot attach mtd2
error 17 (File exists)
ubimkvol: error!: UBI device does not have free logical erasebloubi1: attaching mtd3
cks
!!!ERROR:ubimkvol failed for config partition
ubi1: scanning is finished
ubi1: attached mtd3 (name "resources", size 512 MiB)
ubi1: PEB size: 1048576 bytes (1024 KiB), LEB size: 1040384 bytes
ubi1: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
ubi1: VID header offset: 4096 (aligned 4096), data offset: 8192
ubi1: good PEBs: 504, bad PEBs: 8, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 677597375
ubi1: available PEBs: 0, total reserved PEBs: 504, PEBs reserved for bad PEB handling: 32
ubi1: background thread "ubi_bgt1d" started, PID 582
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 586
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "resources"
UBIFS (ubi1:0): LEB size: 1040384 bytes (1016 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes
UBIFS (ubi1:0): FS size: 476495872 bytes (454 MiB, 458 LEBs), journal size 23928832 bytes (22 MiB, 23 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 8068C335-3096-4AA2-983E-4659B278DEBA, small LPT model
UBIFS (ubi1:0): full atime support is enabled.
Resource partition is mounted!!
Restore is Done
Kernel crashdump is disabled.
Backup is fine
dma_mem_base: 0x96000000, dma_mem_len: 0x8000000, warm_mem_base: 0x9f500000, warm_mem_len: 0xb00000
Creating TUN device
Starting TPM Infra
Group tss and User tss created
kernel.hostname = localhost
hostname set to localhost
Starting TCSD Daemon
TCSD Up and Running
Enabling time stamp.
Starting the FastIron.
USER=root
HOME=/
GCOV_PREFIX=/fast_iron
ethaddr=78:a6:e1:2e:48:29?
TERM=vt102
PATH=/sbin:/usr/sbin:/bin:/usr/bin
crashkernel=64M@0x70000000
ip=192.168.0.210:192.168.0.14::255.255.255.0:MN:eth0:off
SHELL=/bin/sh
PWD=/
i2c-0 i2c Broadcom iProc I2C adapter I2C adapter 2
i2c-1 i2c Broadcom iProc I2C adapter I2C adapter 2
!!!WARNING: Unable to read Filesystem information!!!
Total no. of blocks in FS = 0
Total no. of free blocks = 0
FIPS Disabled:PORT NOT DISABLED
platform type 90
OS>
Loaded Image SPR08080e from Pri Built on (UTC): Tue Apr 9 10:25:33 2019
Enabling Console Logging
flash_file=0.
Upgrade from pre 8.0.80 image. Dual mode to VLAN config upgrade needed
Hotplugger Daemon Initialized ..
External USB disk is not mounted or plugged in.
set_board_level: gi_board_type = 116[ 628.362222] linux-kernel-bde: map phys range 0x3200000-0x3240000 to 0xb0d09000-0xb0d49000
[ 628.544467] linux-kernel-bde: map phys range 0x88100000-0x90100000 to 0xa8c00000-0xb0c00000
DMA pool size: 134217728
PHY Reset De-asserted
sw_pp_sdk_init:137 ToR init
SOC unit 0 attached to PCI device BCM56160_B0
Firmware version from File: 2.1.1
Pre Parsing Config Data ...
Done with Pre-allocating nexthop id's for Unicast & Openflow