Has anyone else updated their switches (atleast ICX 6110) to the 8.0.30u image?
I updated my homelab switch last night and although it's working normally, the temperatures reported jumped way up. Prior to the update, the CPU temp was reporting around 50-52C for the past year consistently according to my LibreNMS graphs. Starting after yesterday's update, the CPU temp is consistent at about 65C.
The switch is in my basement and temps there remain fairly consistent year round with no spike last night. No other servers in the rack show any temperature deviations.
The switch is nearly idle at all times, the CPU load never shows above 1%. It does my Layer3 switching with ACLs, and has 10Gbit links to the servers and an ICX6450. Only 3 PoE devices are plugged into it (VoIP phone, Unifi AC-Lite, Reolink IP camera).
Code:
SSH@brocore>show ver
Copyright (c) 1996-2016 Brocade Communications Systems, Inc. All rights reserved.
UNIT 1: compiled on Apr 23 2020 at 13:17:12 labeled as FCXR08030u
(10545591 bytes) from Primary FCXR08030u.bin
SW: Version 08.0.30uT7f3
Boot-Monitor Image size = 370695, Version:10.1.00T7f5 (grz10100)
HW: Stackable ICX6610-48-HPOE
==========================================================================
UNIT 1: SL 1: ICX6610-48P POE 48-port Management Module
Serial #: BXP2502J2B8
License: ICX6610_ADV_ROUTER_SOFT_PACKAGE (LID: dzrHKFHlHdN)
P-ENGINE 0: type E02B, rev 01
P-ENGINE 1: type E02B, rev 01
==========================================================================
UNIT 1: SL 2: ICX6610-QSFP 10-port 160G Module
==========================================================================
UNIT 1: SL 3: ICX6610-8-port Dual Mode(SFP/SFP+) Module
==========================================================================
800 MHz Power PC processor 8544E (version 0021/0023) 400 MHz bus
65536 KB flash memory
512 MB DRAM
STACKID 1 system uptime is 15 hour(s) 33 minute(s) 10 second(s)
The system started at 20:14:07 Eastern Fri May 15 2020
The system : started=warm start reloaded=by "reload"
SSH@brocore>show cha
The stack unit 1 chassis info:
Power supply 1 (AC - PoE) present, status ok
Model Number: 23-0000142-02
Serial Number: BBY
Firmware Ver: A
Power supply 1 Fan Air Flow Direction: Front to Back
Power supply 2 (AC - PoE) present, status ok
Model Number: 23-0000142-02
Serial Number: FRW
Firmware Ver: A
Power supply 2 Fan Air Flow Direction: Front to Back
Fan 1 ok, speed (auto): [[1]]<->2
Fan 2 ok, speed (auto): [[1]]<->2
Fan controlled temperature: 66.0 deg-C
Fan speed switching temperature thresholds:
Speed 1: NM<----->76 deg-C
Speed 2: 71<-----> 80 deg-C (shutdown)
Fan 1 Air Flow Direction: Front to Back
Fan 2 Air Flow Direction: Front to Back
MAC 1 Temperature Readings:
Current temperature : 53.0 deg-C
MAC 2 Temperature Readings:
Current temperature : 57.5 deg-C
CPU Temperature Readings:
Current temperature : 65.0 deg-C
sensor A Temperature Readings:
Current temperature : 59.0 deg-C
sensor B Temperature Readings:
Current temperature : 55.5 deg-C
sensor C Temperature Readings:
Current temperature : 41.0 deg-C
stacking card Temperature Readings:
Current temperature : 59.0 deg-C
Warning level.......: 68.0 deg-C
Shutdown level......: 80.0 deg-C
Side note, was anyone else's account deleted with the new forum switch?
@fohdeesha , can you please PM me the private switch site info again since it was in my deleted account's inbox?