U-Boot -svn12133 (Oct 30 2014 - 17:38:21)
DEV ID = 0xdc14
SKU ID = 0xb344
DDR type: DDR3
MEMC 0 DDR speed = 750MHz
ddr_init2: Calling soc_ddr40_set_shmoo_dram_config
ddr_init2: Calling soc_ddr40_phy_calibrate
DDR phy calibration passed
Programming controller register
ddr_init2: Calling soc_ddr40_shmoo_ctl
Validate Shmoo parameters stored in flash ..... OK
Press Ctrl-C to run Shmoo ..... skipped
Restoring Shmoo parameters from flash ..... done
Running simple memory test ..... OK
Enabling DDR ECC reporting
GPIO Reaset Reason is 0x0
COLD BOOT: Clearing entire memory
BIST Start 0x0, END 0x3ffffff
clear_ddr: OK
Enabling DDR ECC correction
DDR Tune Completed
Micron MT29F16G08CBACA, blocks per lun: 80000 lun count: 1
1024 KiB blocks, 4 KiB pages, 27B OOB, 8-bit
NAND: chipsize !!!!In env_relocate_spec
NOw reading
!!!calling import
UBOOT: BE Mode
SICA24 Copper (POE), A1
SYS CPLD VER: 0x3, Released Ver: 0
Booted From: Uboot partition 1
Enter 'b' to stop at boot monitor: 0
ICX7250-Boot> dir
Unknown command 'dir' - try 'help'
ICX7250-Boot> setenv
baudrate bootcmd bootdelay bootfile consoledev defbootcmd ethact flash_addr
hostname image_name loadaddr maxcpus netmask quiet serverip stderr stdin
stdout ...
ICX7250-Boot> help
? - alias for 'help'
boot - boot default, i.e., run 'bootcmd'
boot_primary- boot_primary - primary boot; boot from primary partition
boot_secondary- boot_secondary - secondary boot; boot from secondary partition
bootm - boot application image from memory
cp - memory copy
cpld_read- Read from cpld
cpld_write- write to cpld
cplddl - cplddl - To perform cpld download
dump_cpld- Dump CPLD Registers
eeprom - EEPROM sub-system
ext2load- load binary file from a Ext2 filesystem
ext2ls - list files in a directory (default /)
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
gpio_read- Read from GPIO
gpio_write- write to GPIO
help - print command description/usage
hwinfo - Show HW Info
i2c - I2C sub-system
i2c_test- Test i2c bus
i2cread - I2c read
i2cwrite- I2c write
logging_disable- Disable Uboot Logs.
logging_enable- Enable Uboot Logs.
md - memory display
memtest - memtest - To perform memory test
mii - MII utility commands
mtdparts- define flash/nand partitions
mw - memory write (fill)
nand - NAND sub-system
ping - send ICMP ECHO_REQUEST to network host
powercycle- Do a Hard Reset
printenv- print environment variables
reset - Perform RESET of the CPU
saveenv - save environment variables to persistent storage
setenv - set environment variables
sf - SPI flash sub-system
show_image- Show Stored Images.
tftpboot- tftpboot- boot image via network using TFTP protocol
ubi - ubi commands
update_primary- update_secondary - secondary update; update primary partition
update_secondary- update_secondary - secondary update; update secondary partition
update_uboot- update_uboot - get the uboot image over tftp.
usb - USB sub-system
verify - Verify Image
version - print monitor, compiler and linker version
ICX7250-Boot>
ICX7250-Boot> printenv
baudrate=9600
ipaddr=172.21.6.124
serverip=172.21.7.253
netmask=255.255.0.0
image_name=SICA_UBOOT_0.0.8.bin
ver=10.1.01T215 (Oct 30 2014 - 17:38:34)
Environment size: 149/16380 bytes
ICX7250-Boot>
ICX7250-Boot> show_image
===========================
Primary : no current device selected
EMPTY
Secondary: no current device selected
EMPTY
===========================
ICX7250-Boot> fa
fatinfo fatls fatload factory false