Part way through following fodeesha's excellent guide, I hit a boot loop on my ICX 7150. I completed update_primary and got stuck in a boot loop updating the CPLD. It repeats this over and over. I know this upgrade cycle can take a while, but I waited about 20 minutes and it was still stuck in this loop.
Short version:
Long version:
Short version:
Code:
Installed CPLD Version 0x4:0x7
Recommended CPLD Version 0x4:0xa
Upgrading CPLD to 0x4:0xa
CPLD is upgraded Successfully !!!
!!WARNING: System is going to Power Cycle to load new CPLD !!
Code:
ICX7150-Boot>update_primary
Load addr=0x70000000
Change GMAC speed to 1000MB
Using bcm_xgs_gmac-0 device
TFTP from server 10.20.30.1; our IP address is 10.20.30.2
Filename 'SPR08090mc.bin'.
Load address: 0x70000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
####################################
6.3 MiB/s
done
Bytes transferred = 33554432 (2000000 hex)
img_sz=0x2000000 block_count = 0x20
NAND erase.spread: device 0 offset 0x0, size 0x2000000
Erasing at 0x1f00000 -- 100% complete.
OK
NAND write: device 0 offset 0x0, size 0x2000000
33554432 bytes written: OK
TFTP to Flash Done.
ICX7150-Boot>setenv ipaddr
ICX7150-Boot>saveenv
ICX7150-Boot>boot_primary
resetting ...
device 0 offset 0x0, size 0xc0000
using GPIO[7] to reset
Brocade Bootloader: 10.1.10T225 (Jun 25 2017 - 02:25:01 -0700)
Booted from partition 1
DRAM: Validate Shmoo parameters stored in flash ..... OK
ICX7150-12 (POE), PVT1
SYS CPLD VER: 0x4 Released Ver: 0x7
Writing Shmoo values into flash .....
device 0 offset 0x0, size 0xc0000
Enter 'b' to stop at boot monitor: 0
device 0 offset 0x0, size 0xc0000
bootdelay: ===
Booting image from Primary
NAND read: device 0 offset 0x0, size 0x2000000
33554432 bytes read: OK
## Loading kernel from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'kernel@2' kernel subimage
Description: Ruckus Linux MN VER=08.0.90mc
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x7024fc24
Data Size: 2400471 Bytes = 2.3 MiB
Architecture: ARM
OS: Linux
Load Address: 0x61008000
Entry Point: 0x61008000
Hash algo: crc32
Hash value: d980a458
## Loading kernel from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'kernel@2' kernel subimage
Description: Ruckus Linux MN VER=08.0.90mc
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x7024fc24
Data Size: 2400471 Bytes = 2.3 MiB
Architecture: ARM
OS: Linux
Load Address: 0x61008000
Entry Point: 0x61008000
Hash algo: crc32
Hash value: d980a458
Verifying Hash Integrity ... crc32+ OK
## Loading ramdisk from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'ramdisk@1' ramdisk subimage
Description: Ramdisk -rootfs
Type: RAMDisk Image
Compression: lzma compressed
Data Start: 0x704a06b0
Data Size: 27720752 Bytes = 26.4 MiB
Architecture: ARM
OS: Linux
Load Address: 0x00000000
Entry Point: 0x00000000
Hash algo: crc32
Hash value: e9b25165
Verifying Hash Integrity ... crc32+ OK
## Loading fdt from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'fdt@3' fdt subimage
Description: Flattened Device Tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x7049e458
Data Size: 8607 Bytes = 8.4 KiB
Architecture: ARM
Hash algo: crc32
Hash value: 6fc9a37b
Verifying Hash Integrity ... crc32+ OK
Loading fdt from 0x7049e458 to 0x65008000
Booting using the fdt blob at 0x65008000
Uncompressing Kernel Image ... OK
Using Device Tree in place at 65008000, end 6500d19e
Starting kernel ...
Mounting file system...
booting with 4.4 kernel
NAND Type: Micron NAND 2GiB (x 1)
PLATFORM MN
dd cmd: UBI
Config partition mounted
Resource partition is mounted!!
CTRL-B Z for help | 9600 8N1 | NOR | Minicom 2.8 | VT102 | Offline | ttyUSB0
Please download UFI image to install packages
/etc/process_packages.sh: line 148: can't create /.pkg/error.log: nonexistent directory
Package installation is incomplete, related functionalities may not be available
dhcpd executable file is not present.
Starting up system statistics daemon...
Starting systatsd done
Starting up health monitor daemon...
Log Level 7: Daemonized systatsd
Systatsd Logging Env is not set, initializing loglevel to: 7
Setting connection to systemlogger
Starting hmond done
Hmond Logging Env is not set, initializing loglelvel to: I
Setting connection to systemlogger
Backup is fine
Kernel crashdump is disabled.
FIPS reset is enable.
Removing startup config & backup
Removing stacking.boot
Remodma_mem_base: 0x96000000, dma_mem_len: 0x8000000, warm_mem_base: 0x9f500000, warm_mem_len: 0xb00000
ving SSL_CERT_FILE
Removing SSH_RSA_HOSTKEY_FILE
Removing SSH_DSA_HOSTKEY_FILE
Creating TUN device
Starting TPM Infra
Group tss and User tss created
kernel.hostname = localhost
hostname set to localhost
Starting TCSD Daemon
TCSD Up and Running
Enabling time stamp.
Starting the FastIron.
USER=root
HOME=/
GCOV_PREFIX=/fast_iron
ethaddr=60:9c:9f:e7:0c:9d?
TERM=vt102
PATH=/sbin:/usr/sbin:/bin:/usr/bin
crashkernel=64M@0x70000000
ip=:10.20.30.1:10.20.30.1:255.255.255.0:MN:eth0:off
SHELL=/bin/sh
PWD=/
i2c-0 i2c Broadcom iProc I2C adapter I2C adapter 2
i2c-1 i2c Broadcom iProc I2C adapter I2C adapter 2
FIPS Disabled:PORT NOT DISABLED
platform type 90
OS>
Loaded Image SPR08090mc from Pri Built on (UTC): Mon Oct 4 17:51:11 2021
Enabling Console Logging
Installed CPLD Version 0x4:0x7
Recommended CPLD Version 0x4:0xa
Upgrading CPLD to 0x4:0xa
CPLD is upgraded Successfully !!!
!!WARNING: System is going to Power Cycle to load new CPLD !!
CPLD is upgraded Successfully !!!Applying factory defaults..
sil_ramfs_creat: Failed to create file /var/log/pdc/pdc_errorlog.txt
Could not create ramfs file!
pdc_errorlog
Could not open ramfs file!
fitrace_tmp.errorlogINFO: startup config data is not available, try to read from backup
INFO: startup config data in the backup area is not available
Stopping health monitor daemon...
Stopped health monitor daemon
Stopping system statistics daemon...
Sent SIGTERM to all processes
[ 80.290001] [BrcdSoftlockup]: root e501cd80 is not a valid rb_tree
Sent SIGKILL to all processes
Requesting system reboot
[ 81.790339] reboot: Restarting system
[ 81.834237] Asserting GHPIO[7] reset sequence from Kernel ...
Brocade Bootloader: 10.1.10T225 (Jun 25 2017 - 02:25:01 -0700)
Booted from partition 1
DRAM: Validate Shmoo parameters stored in flash ..... OK
ICX7150-12 (POE), PVT1
SYS CPLD VER: 0x4 Released Ver: 0x7
Writing Shmoo values into flash .....
device 0 offset 0x0, size 0xc0000
Enter 'b' to stop at boot monitor: 0
device 0 offset 0x0, size 0xc0000
bootdelay: ===
Booting image from Primary
NAND read: device 0 offset 0x0, size 0x2000000
33554432 bytes read: OK
## Loading kernel from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'kernel@2' kernel subimage
Description: Ruckus Linux MN VER=08.0.90mc
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x7024fc24
Data Size: 2400471 Bytes = 2.3 MiB
Architecture: ARM
OS: Linux
Load Address: 0x61008000
Entry Point: 0x61008000
Hash algo: crc32
Hash value: d980a458
## Loading kernel from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'kernel@2' kernel subimage
Description: Ruckus Linux MN VER=08.0.90mc
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x7024fc24
Data Size: 2400471 Bytes = 2.3 MiB
Architecture: ARM
OS: Linux
Load Address: 0x61008000
Entry Point: 0x61008000
Hash algo: crc32
Hash value: d980a458
Verifying Hash Integrity ... crc32+ OK
## Loading ramdisk from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'ramdisk@1' ramdisk subimage
Description: Ramdisk -rootfs
Type: RAMDisk Image
Compression: lzma compressed
Data Start: 0x704a06b0
Data Size: 27720752 Bytes = 26.4 MiB
Architecture: ARM
OS: Linux
Load Address: 0x00000000
Entry Point: 0x00000000
Hash algo: crc32
Hash value: e9b25165
Verifying Hash Integrity ... crc32+ OK
## Loading fdt from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'fdt@3' fdt subimage
Description: Flattened Device Tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x7049e458
Data Size: 8607 Bytes = 8.4 KiB
Architecture: ARM
Hash algo: crc32
Hash value: 6fc9a37b
Verifying Hash Integrity ... crc32+ OK
Loading fdt from 0x7049e458 to 0x65008000
Booting using the fdt blob at 0x65008000
Uncompressing Kernel Image ... OK
Using Device Tree in place at 65008000, end 6500d19e
Starting kernel ...
Mounting file system...
booting with 4.4 kernel
NAND Type: Micron NAND 2GiB (x 1)
PLATFORM MN
dd cmd: UBI
Config partition mounted
Resource partition is mounted!!
Please download UFI image to install packages
/etc/process_packages.sh: line 148: can't create /.pkg/error.log: nonexistent directory
Package installation is incomplete, related functionalities may not be available
dhcpd executable file is not present.
Starting up system statistics daemon...
Starting systatsd done
Starting up health monitor daemon...
Log Level 7: Daemonized systatsd
Systatsd Logging Env is not set, initializing loglevel to: 7
Setting connection to systemlogger
Starting hmond done
Hmond Logging Env is not set, initializing loglelvel to: I
Setting connection to systemlogger
Backup is fine
Kernel crashdump is disabled.
dma_mem_base: 0x96000000, dma_mem_len: 0x8000000, warm_mem_base: 0x9f500000, warm_mem_len: 0xb00000
Creating TUN device
Starting TPM Infra
Group tss and User tss created
kernel.hostname = localhost
hostname set to localhost
Starting TCSD Daemon
TCSD Up and Running
Enabling time stamp.
Starting the FastIron.
USER=root
HOME=/
GCOV_PREFIX=/fast_iron
ethaddr=60:9c:9f:e7:0c:9d?
TERM=vt102
PATH=/sbin:/usr/sbin:/bin:/usr/bin
crashkernel=64M@0x70000000
ip=:10.20.30.1:10.20.30.1:255.255.255.0:MN:eth0:off
SHELL=/bin/sh
PWD=/
i2c-0 i2c Broadcom iProc I2C adapter I2C adapter 2
i2c-1 i2c Broadcom iProc I2C adapter I2C adapter 2
FIPS Disabled:PORT NOT DISABLED
platform type 90
OS>
Loaded Image SPR08090mc from Pri Built on (UTC): Mon Oct 4 17:51:11 2021
Enabling Console Logging
Installed CPLD Version 0x4:0x7
Recommended CPLD Version 0x4:0xa
Upgrading CPLD to 0x4:0xa
CPLD is upgraded Successfully !!!
!!WARNING: System is going to Power Cycle to load new CPLD !!
CPLD is upgraded Successfully !!!Applying factory defaults..
sil_ramfs_creat: Failed to create file /var/log/pdc/pdc_errorlog.txt
Could not create ramfs file!
pdc_errorlog
Could not open ramfs file!
fitrace_tmp.errorlogINFO: startup config data is not available, try to read from backup
INFO: startup config data in the backup area is not available
Hotplugger Daemon Initialized ..
Stopping health monitor daemon...
External USB disk is not mounted or plugged in.
Sent SIGTERM to all processes
Sent SIGKILL to all processes
Requesting system reboot
[ 76.820337] reboot: Restarting system
[ 76.864236] Asserting GHPIO[7] reset sequence from Kernel ...
Brocade Bootloader: 10.1.10T225 (Jun 25 2017 - 02:25:01 -0700)
Booted from partition 1
DRAM: Validate Shmoo parameters stored in flash ..... OK
ICX7150-12 (POE), PVT1
SYS CPLD VER: 0x4 Released Ver: 0x7
Writing Shmoo values into flash .....
device 0 offset 0x0, size 0xc0000
Enter 'b' to stop at boot monitor: 0
device 0 offset 0x0, size 0xc0000
bootdelay: ===
Booting image from Primary
NAND read: device 0 offset 0x0, size 0x2000000
33554432 bytes read: OK
## Loading kernel from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'kernel@2' kernel subimage
Description: Ruckus Linux MN VER=08.0.90mc
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x7024fc24
Data Size: 2400471 Bytes = 2.3 MiB
Architecture: ARM
OS: Linux
Load Address: 0x61008000
Entry Point: 0x61008000
Hash algo: crc32
Hash value: d980a458
## Loading kernel from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'kernel@2' kernel subimage
Description: Ruckus Linux MN VER=08.0.90mc
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x7024fc24
Data Size: 2400471 Bytes = 2.3 MiB
Architecture: ARM
OS: Linux
Load Address: 0x61008000
Entry Point: 0x61008000
Hash algo: crc32
Hash value: d980a458
Verifying Hash Integrity ... crc32+ OK
## Loading ramdisk from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'ramdisk@1' ramdisk subimage
Description: Ramdisk -rootfs
Type: RAMDisk Image
Compression: lzma compressed
Data Start: 0x704a06b0
Data Size: 27720752 Bytes = 26.4 MiB
Architecture: ARM
OS: Linux
Load Address: 0x00000000
Entry Point: 0x00000000
Hash algo: crc32
Hash value: e9b25165
Verifying Hash Integrity ... crc32+ OK
## Loading fdt from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'fdt@3' fdt subimage
Description: Flattened Device Tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x7049e458
Data Size: 8607 Bytes = 8.4 KiB
Architecture: ARM
Hash algo: crc32
Hash value: 6fc9a37b
Verifying Hash Integrity ... crc32+ OK
Loading fdt from 0x7049e458 to 0x65008000
Booting using the fdt blob at 0x65008000
Uncompressing Kernel Image ... OK
Using Device Tree in place at 65008000, end 6500d19e
Starting kernel ...
Mounting file system...
booting with 4.4 kernel
NAND Type: Micron NAND 2GiB (x 1)
PLATFORM MN
dd cmd: UBI
Config partition mounted
Resource partition is mounted!!
Please download UFI image to install packages
/etc/process_packages.sh: line 148: can't create /.pkg/error.log: nonexistent directory
Package installation is incomplete, related functionalities may not be available
dhcpd executable file is not present.
Starting up system statistics daemon...
Starting systatsd done
Starting up health monitor daemon...
Log Level 7: Daemonized systatsd
Systatsd Logging Env is not set, initializing loglevel to: 7
Setting connection to systemlogger
Starting hmond done
Hmond Logging Env is not set, initializing loglelvel to: I
Setting connection to systemlogger
Backup is fine
Kernel crashdump is disabled.
dma_mem_base: 0x96000000, dma_mem_len: 0x8000000, warm_mem_base: 0x9f500000, warm_mem_len: 0xb00000
Creating TUN device
Starting TPM Infra
Group tss and User tss created
kernel.hostname = localhost
hostname set to localhost
Starting TCSD Daemon
TCSD Up and Running
Enabling time stamp.
Starting the FastIron.
USER=root
HOME=/
GCOV_PREFIX=/fast_iron
ethaddr=60:9c:9f:e7:0c:9d?
TERM=vt102
PATH=/sbin:/usr/sbin:/bin:/usr/bin
crashkernel=64M@0x70000000
ip=:10.20.30.1:10.20.30.1:255.255.255.0:MN:eth0:off
SHELL=/bin/sh
PWD=/
i2c-0 i2c Broadcom iProc I2C adapter I2C adapter 2
i2c-1 i2c Broadcom iProc I2C adapter I2C adapter 2
FIPS Disabled:PORT NOT DISABLED
platform type 90
OS>
Loaded Image SPR08090mc from Pri Built on (UTC): Mon Oct 4 17:51:11 2021
Enabling Console Logging
Installed CPLD Version 0x4:0x7
Recommended CPLD Version 0x4:0xa
Upgrading CPLD to 0x4:0xa
CPLD is upgraded Successfully !!!
!!WARNING: System is going to Power Cycle to load new CPLD !!
CPLD is upgraded Successfully !!!Applying factory defaults..
sil_ramfs_creat: Failed to create file /var/log/pdc/pdc_errorlog.txt
Could not create ramfs file!
pdc_errorlog
Could not open ramfs file!
fitrace_tmp.errorlogINFO: startup config data is not available, try to read from backup
INFO: startup config data in the backup area is not available
Hotplugger Daemon Initialized ..
Stopping health monitor daemon...
External USB disk is not mounted or plugged in.
Sent SIGTERM to all processes
Sent SIGKILL to all processes
Requesting system reboot
[ 76.860343] reboot: Restarting system
[ 76.904241] Asserting GHPIO[7] reset sequence from Kernel ...
Brocade Bootloader: 10.1.10T225 (Jun 25 2017 - 02:25:01 -0700)
Booted from partition 1
DRAM: Validate Shmoo parameters stored in flash ..... OK
ICX7150-12 (POE), PVT1
SYS CPLD VER: 0x4 Released Ver: 0x7
Writing Shmoo values into flash .....
device 0 offset 0x0, size 0xc0000
Enter 'b' to stop at boot monitor: 0
device 0 offset 0x0, size 0xc0000
bootdelay: ===
Booting image from Primary
NAND read: device 0 offset 0x0, size 0x2000000
33554432 bytes read: OK
## Loading kernel from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'kernel@2' kernel subimage
Description: Ruckus Linux MN VER=08.0.90mc
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x7024fc24
Data Size: 2400471 Bytes = 2.3 MiB
Architecture: ARM
OS: Linux
Load Address: 0x61008000
Entry Point: 0x61008000
Hash algo: crc32
Hash value: d980a458
## Loading kernel from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'kernel@2' kernel subimage
Description: Ruckus Linux MN VER=08.0.90mc
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x7024fc24
Data Size: 2400471 Bytes = 2.3 MiB
Architecture: ARM
OS: Linux
Load Address: 0x61008000
Entry Point: 0x61008000
Hash algo: crc32
Hash value: d980a458
Verifying Hash Integrity ... crc32+ OK
## Loading ramdisk from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'ramdisk@1' ramdisk subimage
Description: Ramdisk -rootfs
Type: RAMDisk Image
Compression: lzma compressed
Data Start: 0x704a06b0
Data Size: 27720752 Bytes = 26.4 MiB
Architecture: ARM
OS: Linux
Load Address: 0x00000000
Entry Point: 0x00000000
Hash algo: crc32
Hash value: e9b25165
Verifying Hash Integrity ... crc32+ OK
## Loading fdt from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'fdt@3' fdt subimage
Description: Flattened Device Tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x7049e458
Data Size: 8607 Bytes = 8.4 KiB
Architecture: ARM
Hash algo: crc32
Hash value: 6fc9a37b
Verifying Hash Integrity ... crc32+ OK
Loading fdt from 0x7049e458 to 0x65008000
Booting using the fdt blob at 0x65008000
Uncompressing Kernel Image ... OK
Using Device Tree in place at 65008000, end 6500d19e
Starting kernel ...
Mounting file system...
booting with 4.4 kernel
NAND Type: Micron NAND 2GiB (x 1)
PLATFORM MN
dd cmd: UBI
Config partition mounted
Resource partition is mounted!!
Please download UFI image to install packages
/etc/process_packages.sh: line 148: can't create /.pkg/error.log: nonexistent directory
Package installation is incomplete, related functionalities may not be available
dhcpd executable file is not present.
Starting up system statistics daemon...
Starting systatsd done
Starting up health monitor daemon...
Log Level 7: Daemonized systatsd
Systatsd Logging Env is not set, initializing loglevel to: 7
Setting connection to systemlogger
Starting hmond done
Hmond Logging Env is not set, initializing loglelvel to: I
Setting connection to systemlogger
Backup is fine
Kernel crashdump is disabled.
dma_mem_base: 0x96000000, dma_mem_len: 0x8000000, warm_mem_base: 0x9f500000, warm_mem_len: 0xb00000
Creating TUN device
Starting TPM Infra
Group tss and User tss created
kernel.hostname = localhost
hostname set to localhost
Starting TCSD Daemon
TCSD Up and Running
Enabling time stamp.
Starting the FastIron.
USER=root
HOME=/
GCOV_PREFIX=/fast_iron
ethaddr=60:9c:9f:e7:0c:9d?
TERM=vt102
PATH=/sbin:/usr/sbin:/bin:/usr/bin
crashkernel=64M@0x70000000
ip=:10.20.30.1:10.20.30.1:255.255.255.0:MN:eth0:off
SHELL=/bin/sh
PWD=/
i2c-0 i2c Broadcom iProc I2C adapter I2C adapter 2
i2c-1 i2c Broadcom iProc I2C adapter I2C adapter 2
FIPS Disabled:PORT NOT DISABLED
platform type 90
OS>
Loaded Image SPR08090mc from Pri Built on (UTC): Mon Oct 4 17:51:11 2021
Enabling Console Logging
Installed CPLD Version 0x4:0x7
Recommended CPLD Version 0x4:0xa
Upgrading CPLD to 0x4:0xa
CPLD is upgraded Successfully !!!
!!WARNING: System is going to Power Cycle to load new CPLD !!
CPLD is upgraded Successfully !!!Applying factory defaults..
sil_ramfs_creat: Failed to create file /var/log/pdc/pdc_errorlog.txt
Could not create ramfs file!
pdc_errorlog
Could not open ramfs file!
fitrace_tmp.errorlogINFO: startup config data is not available, try to read from backup
INFO: startup config data in the backup area is not available
Hotplugger Daemon Initialized ..
Stopping health monitor daemon...
External USB disk is not mounted or plugged in.
Sent SIGTERM to all processes
Sent SIGKILL to all processes
Requesting system reboot
[ 76.760342] reboot: Restarting system
[ 76.804238] Asserting GHPIO[7] reset sequence from Kernel ...
Brocade Bootloader: 10.1.10T225 (Jun 25 2017 - 02:25:01 -0700)
Booted from partition 1
DRAM: Validate Shmoo parameters stored in flash ..... OK
ICX7150-12 (POE), PVT1
SYS CPLD VER: 0x4 Released Ver: 0x7
Writing Shmoo values into flash .....
device 0 offset 0x0, size 0xc0000
Enter 'b' to stop at boot monitor: 0
device 0 offset 0x0, size 0xc0000
bootdelay: ===
Booting image from Primary
NAND read: device 0 offset 0x0, size 0x2000000
33554432 bytes read: OK
## Loading kernel from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'kernel@2' kernel subimage
Description: Ruckus Linux MN VER=08.0.90mc
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x7024fc24
Data Size: 2400471 Bytes = 2.3 MiB
Architecture: ARM
OS: Linux
Load Address: 0x61008000
Entry Point: 0x61008000
Hash algo: crc32
Hash value: d980a458
## Loading kernel from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'kernel@2' kernel subimage
Description: Ruckus Linux MN VER=08.0.90mc
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x7024fc24
Data Size: 2400471 Bytes = 2.3 MiB
Architecture: ARM
OS: Linux
Load Address: 0x61008000
Entry Point: 0x61008000
Hash algo: crc32
Hash value: d980a458
Verifying Hash Integrity ... crc32+ OK
## Loading ramdisk from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'ramdisk@1' ramdisk subimage
Description: Ramdisk -rootfs
Type: RAMDisk Image
Compression: lzma compressed
Data Start: 0x704a06b0
Data Size: 27720752 Bytes = 26.4 MiB
Architecture: ARM
OS: Linux
Load Address: 0x00000000
Entry Point: 0x00000000
Hash algo: crc32
Hash value: e9b25165
Verifying Hash Integrity ... crc32+ OK
## Loading fdt from FIT Image at 70000200 ...
Using 'conf@1' configuration
Trying 'fdt@3' fdt subimage
Description: Flattened Device Tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x7049e458
Data Size: 8607 Bytes = 8.4 KiB
Architecture: ARM
Hash algo: crc32
Hash value: 6fc9a37b
Verifying Hash Integrity ... crc32+ OK
Loading fdt from 0x7049e458 to 0x65008000
Booting using the fdt blob at 0x65008000
Uncompressing Kernel Image ... OK
Using Device Tree in place at 65008000, end 6500d19e
Starting kernel ...
Mounting file system...
booting with 4.4 kernel
NAND Type: Micron NAND 2GiB (x 1)
PLATFORM MN
dd cmd: UBI
Config partition mounted
Resource partition is mounted!!
Please download UFI image to install packages
/etc/process_packages.sh: line 148: can't create /.pkg/error.log: nonexistent directory
Package installation is incomplete, related functionalities may not be available
dhcpd executable file is not present.
Starting up system statistics daemon...
Starting systatsd done
Starting up health monitor daemon...
Log Level 7: Daemonized systatsd
Systatsd Logging Env is not set, initializing loglevel to: 7
Setting connection to systemlogger
Starting hmond done
Hmond Logging Env is not set, initializing loglelvel to: I
Setting connection to systemlogger
Backup is fine
Kernel crashdump is disabled.
dma_mem_base: 0x96000000, dma_mem_len: 0x8000000, warm_mem_base: 0x9f500000, warm_mem_len: 0xb00000
Creating TUN device
Starting TPM Infra
Group tss and User tss created
kernel.hostname = localhost
hostname set to localhost
Starting TCSD Daemon
TCSD Up and Running
Enabling time stamp.
Starting the FastIron.
USER=root
HOME=/
GCOV_PREFIX=/fast_iron
ethaddr=60:9c:9f:e7:0c:9d?
TERM=vt102
PATH=/sbin:/usr/sbin:/bin:/usr/bin
crashkernel=64M@0x70000000
ip=:10.20.30.1:10.20.30.1:255.255.255.0:MN:eth0:off
SHELL=/bin/sh
PWD=/
i2c-0 i2c Broadcom iProc I2C adapter I2C adapter 2
i2c-1 i2c Broadcom iProc I2C adapter I2C adapter 2
FIPS Disabled:PORT NOT DISABLED
platform type 90
OS>
Loaded Image SPR08090mc from Pri Built on (UTC): Mon Oct 4 17:51:11 2021
Enabling Console Logging
Installed CPLD Version 0x4:0x7
Recommended CPLD Version 0x4:0xa
Upgrading CPLD to 0x4:0xa
CPLD is upgraded Successfully !!!
!!WARNING: System is going to Power Cycle to load new CPLD !!
CPLD is upgraded Successfully !!!Applying factory defaults..
sil_ramfs_creat: Failed to create file /var/log/pdc/pdc_errorlog.txt
Could not create ramfs file!
pdc_errorlog
Could not open ramfs file!
fitrace_tmp.errorlogINFO: startup config data is not available, try to read from backup
INFO: startup config data in the backup area is not available
Hotplugger Daemon Initialized ..
External USB disk is not mounted or plugged in.
Stopping health monitor daemon...
Sent SIGTERM to all processes
Sent SIGKILL to all processes
Requesting system reboot
[ 76.660339] reboot: Restarting system
[ 76.704237] Asserting GHPIO[7] reset sequence from Kernel ...
Brocade Bootloader: 10.1.10T225 (Jun 25 2017 - 02:25:01 -0700)
Booted from partition 1
DRAM: Validate Shmoo parameters stored in flash ..... OK
ICX7150-12 (POE), PVT1
SYS CPLD VER: 0x4 Released Ver: 0x7
Writing Shmoo values into flash .....
device 0 offset 0x0, size 0xc0000
Enter 'b' to stop at boot monitor: 0
ETC ETC