I have no idea what I'm doing with this Brocade switch. (My "Cisco" SG500X refuses to handshake with the ISP provided ONT.)
With FTTH, Bell provides an SFP ONT and requires PPPoE to connect, on VLAN 35.
Yes, you CAN bypass the HomeHub 3000!! - Bell Canada | DSLReports Forums
On the Brocade, I have 1/3/8 configured to tag vlan 35, then I've tried:
a) an untagged/access vlan35 to my pfsense 2.4.3-p1
and
b) a tagged vlan35 with pfsense tagging vlan35
And the PPPoE won't connect either way. It just cycles endlessly, not receiving any response.
When I move the SFP into the Bell provided HH3000, it connects, so I know the ONT is connected/working, and I know my PPPoE login/password works (I'm not getting any auth failure anyway, just no response.)
PORT-VLAN 35, Name Fibe, Priority level0, Spanning tree Off
Untagged Ports: (U1/M1) 3 4
Tagged Ports: (U1/M1) 2
Tagged Ports: (U1/M3) 1 8
Uplink Ports: None
DualMode Ports: None
Mac-Vlan Ports: None
Monitoring: Disabled
icx6610(config)#show interfaces ethernet 1/3/8
10GigabitEthernet1/3/8 is up, line protocol is up
Port up for 18 hour(s) 59 minute(s) 25 second(s)
Hardware is 10GigabitEthernet, address is (removed)
Interface type is unknown
Configured speed 1Gbit, actual 1Gbit, configured duplex fdx, actual fdx
Member of 3 L2 VLANs, port is tagged, port state is FORWARDING
BPDU guard is Disabled, ROOT protect is Disabled, Designated protect is Disabled
Link Error Dampening is Disabled
STP configured to ON, priority is level1, mac-learning is enabled
Openflow is Disabled, Openflow Hybrid mode is Disabled, Flow Control is enabled
Mirror disabled, Monitor disabled
Mac-notification is disabled
Not member of any active trunks
Not member of any configured trunks
No port name
MTU 10200 bytes, encapsulation ethernet
300 second input rate: 1024 bits/sec, 2 packets/sec, 0.00% utilization
300 second output rate: 1048 bits/sec, 1 packets/sec, 0.00% utilization
29522 packets input, 10640590 bytes, 0 no buffer
Received 0 broadcasts, 5 multicasts, 29517 unicasts
0 input errors, 0 CRC, 0 frame, 0 ignored
0 runts, 0 giants
56876 packets output, 6627605 bytes, 0 underruns
Transmitted 356 broadcasts, 28525 multicasts, 27995 unicasts
0 output errors, 0 collisions
Relay Agent Information option: Disabled
Egress queues:
Queue counters Queued packets Dropped Packets
0 56876 0
1 0 0
2 0 0
3 0 0
4 0 0
5 0 0
6 0 0
7 0 0
So, what should I be doing on my Brocade to get it to take all VLAN 35 traffic, tag it, and egress? And what happens to untagged traffic that happens to come back in from the SFP?
With FTTH, Bell provides an SFP ONT and requires PPPoE to connect, on VLAN 35.
Yes, you CAN bypass the HomeHub 3000!! - Bell Canada | DSLReports Forums
On the Brocade, I have 1/3/8 configured to tag vlan 35, then I've tried:
a) an untagged/access vlan35 to my pfsense 2.4.3-p1
and
b) a tagged vlan35 with pfsense tagging vlan35
And the PPPoE won't connect either way. It just cycles endlessly, not receiving any response.
When I move the SFP into the Bell provided HH3000, it connects, so I know the ONT is connected/working, and I know my PPPoE login/password works (I'm not getting any auth failure anyway, just no response.)
PORT-VLAN 35, Name Fibe, Priority level0, Spanning tree Off
Untagged Ports: (U1/M1) 3 4
Tagged Ports: (U1/M1) 2
Tagged Ports: (U1/M3) 1 8
Uplink Ports: None
DualMode Ports: None
Mac-Vlan Ports: None
Monitoring: Disabled
icx6610(config)#show interfaces ethernet 1/3/8
10GigabitEthernet1/3/8 is up, line protocol is up
Port up for 18 hour(s) 59 minute(s) 25 second(s)
Hardware is 10GigabitEthernet, address is (removed)
Interface type is unknown
Configured speed 1Gbit, actual 1Gbit, configured duplex fdx, actual fdx
Member of 3 L2 VLANs, port is tagged, port state is FORWARDING
BPDU guard is Disabled, ROOT protect is Disabled, Designated protect is Disabled
Link Error Dampening is Disabled
STP configured to ON, priority is level1, mac-learning is enabled
Openflow is Disabled, Openflow Hybrid mode is Disabled, Flow Control is enabled
Mirror disabled, Monitor disabled
Mac-notification is disabled
Not member of any active trunks
Not member of any configured trunks
No port name
MTU 10200 bytes, encapsulation ethernet
300 second input rate: 1024 bits/sec, 2 packets/sec, 0.00% utilization
300 second output rate: 1048 bits/sec, 1 packets/sec, 0.00% utilization
29522 packets input, 10640590 bytes, 0 no buffer
Received 0 broadcasts, 5 multicasts, 29517 unicasts
0 input errors, 0 CRC, 0 frame, 0 ignored
0 runts, 0 giants
56876 packets output, 6627605 bytes, 0 underruns
Transmitted 356 broadcasts, 28525 multicasts, 27995 unicasts
0 output errors, 0 collisions
Relay Agent Information option: Disabled
Egress queues:
Queue counters Queued packets Dropped Packets
0 56876 0
1 0 0
2 0 0
3 0 0
4 0 0
5 0 0
6 0 0
7 0 0
So, what should I be doing on my Brocade to get it to take all VLAN 35 traffic, tag it, and egress? And what happens to untagged traffic that happens to come back in from the SFP?