ASUS KRPA-U16 PCIe bifurcation

Notice: Page may contain affiliate links for which we may earn a small commission through services like Amazon Affiliates or Skimlinks.

boomheadshot

Member
Mar 20, 2021
64
3
8
Is it possible?

I need an NVMe raid (2 x 2TB) for now, was thinking of going up to 4 x 2 TB. Got an ASUS Hyper M.2 X16 G4 and was hoping to set up all of the drives on the adapter.


But it only works if I have 1 SSD installed. Hey, it's good enough for now, 1 in the adapter and one in the M.2 slot on the mobo.

I know it's unsupported officially, but is there really no way to make it work? No bifurcation setting in the BIOS.

I guess I'll just have to sell the adapter and get some cheap adapters from aliexpress or something so each drive is on a separate PCIe slot if it won't be possible to get the ASUS adapter to work.

Oh, and I've got another limitation: I'm afraid I'll have to stick to my 0302 version because I've got an engineering sample (and I've only got a modded BIOS just for this version).
 
why not using the Oculink ? there are 6 x PCIe 3.0x4.
the adapters Oculink -> M.2 may cheap on aliexpress ?
 
Me again.
I have 2 custom bios for asus krpa-u16 for Milan and ROME based on Version 0701(Milan) and Version 4501(ROME). They have been working properly on my boards for over a year, dividing SNLOT No. 1 pci-e x16 into 4x4x4x4.
But I recently received a board with firmware Version 1002(Milan) and was unable to downgrade the bios version. The firmware message says that "the version I'm trying to flash is older than the one that has already been flashed".
Question: does anyone know how to downgrade the bios version?
bmc, flash from bios and dos works without problems, but everywhere there is a failure for the reason mentioned above.
 
OK, it's obvious. then the next question is how to get out of the file.cap to make a dump image that will not ruin the board and will save unique data such as mac, sn ......
 
OK, it's obvious. then the next question is how to get out of the file.cap to make a dump image that will not ruin the board and will save unique data such as mac, sn ......
i have seen this board only with BIOS chip in socket, so you can go back to prev. state any time.
 
I have 2 custom bios for asus krpa-u16 for Milan and ROME based on Version 0701(Milan) and Version 4501(ROME). They have been working properly on my boards for over a year, dividing SNLOT No. 1 pci-e x16 into 4x4x4x4.
mod. the new BIOS 1002 to same bifurcation is not an option ?
( i can try my luck tomorrow )
edit: i need your old mod. BIOS to look inside if possible.
 
Last edited:
is there an option to attach a file to a message?
oops :cool:

Gen3-KRPA-U16-M-ASUS-0701-bifurcation-23071201.rar
The uploaded file is too large for the server to process. :(
 
Last edited:
Heads up!

Formal BIOS Version 5401(ROME) and Version 2301(Milan) Just dropped today 8/17/2026. Any chance one of you mad lads would mod these new bios images to support bifurcation?
 
Apologies, but should the GLink1 display or selection show up in the bios menu?
no. i fixed only to "x4x4x4x4"
dividing SNLOT No. 1 pci-e x16 into 4x4x4x4.

mod. in the wild. PCIe Slot1 should be GLink1 x16 in stock BIOS.
it is probably not accepted by AFUxxx Tolls but IPMI should work.
have you tried smokeless UMAF ?
if not work for you i can try to unsupress BiFurcation options,
but you need to ask again every time a new BIOS comes out.
 
note i can't test this myself.
both Rome and Milan GLink1 to x4x4x4x4
would this work for a 4501 board running 7D12 (Rome)? just making sure since i really can't break this board. is it possible to change the slot that is bifurcated? i need the full length slot (slot 1) so it shouldn't be an issue now but i think i might need another bifurcated slot later on (running one of these: ASRock Hyper Quad M.2 Card: beste prijzen, echte reviews en specificaties - Tweakers)