Search results

  1. J

    X10SLL-F + E3-1230 v3 - Can't boot ESXi 6 or 7 - Ubuntu 20.04 works

    This is some problems with UEFI boot, you can boot in non UEFI (bios) mode. Have same problem on X10SLH-F. Try bios 3.4 and 3.2 version, no change.
  2. J

    Looking for a way to reset Lenovo 930-24i to factory defaults

    https://forums.servethehome.com/index.php?threads/lsi-megacli-preboot-cli-storecli-megascu-megarec-sas2flash-and-megaoem-commands.457/ In this thread, DOS archive
  3. J

    Looking for a way to reset Lenovo 930-24i to factory defaults

    If no jumper to disable enclosure, boot in DOS and try Megarec3 util if it see you raid card. Megarec can clean flash and reflash firmware, but i don't know if it work with sas3508 chip.
  4. J

    Looking for a way to reset Lenovo 930-24i to factory defaults

    Find on Supermicro FAQ's Question If Direct Mapping Mode were accidentally enabled on AOC-SAS2LP-H8iR and has caused the card to stop working, how can a user disable it? Answer Enabling Direct Mapping Mode allows the RAID controller assign drive numbers based how fan-out cables are attached to...
  5. J

    LSI 9361-8i initiallization only on iMR firmware

    Hello! Have some problem with LSI MR 9361-8i raid controller. For some reason MR 9361-8i can boot only on iMR firmware. When I flash on controller MR firmware from LSI FW_16MB.rom or latest MR_4MB.rom it stuck on boot. UART output with MR firmware only. LSI Logic Boot loader V3.02.00.00-0001...
  6. J

    Does anyone want to take a dump on me?

    Don't know, buy it on ebay. No any labels except LSI. On this controller disabled raid 5 & 6 functionally. I have another, but can't reflash it, when flash full firmware from LSI_Preboot then system can't initialise it. Short J6B2 jumper, boot into DOS and megarec3 see it, clean flash, reboot...
  7. J

    Does anyone want to take a dump on me?

    Think this is section what you need But it maybe write this config throuhg UART intarface on controller or some special programming tool. Because some features can change for OEM orders.
  8. J

    SuperMicro H12SSL-NT / AOC-S3108 no Storage Health Information

    Esxi 7 free on X10SRH-CF LSA show integrated sas3008 and add-on sas3108. Install lsi provider, enable sfcbd-watchdog, restart server. Connect to server with administrator account. As I remember this procedure.
  9. J

    SuperMicro 3108 'Bricked'

    Glad that you success reanimate you controller. Think that Megacli.exe from directory "boot\LSI\FW\Recover" is renamed Megarec3. LSI PreBoot Installer for USB also have recovery ROM this is file "FW_16MB.rom" from directory "boot\LSI\FW\Recover".
  10. J

    SuperMicro 3108 'Bricked'

    Use megacli from folder Recover
  11. J

    SuperMicro 3108 'Bricked'

    Hi! You can try flash full 16MB firmware file from LSI PreBoot Installer. In this archive find megacli.exe and fw_16mb.rom in folder Recover. Recover script from LSI in this PreBoot image with error. So you can manually create bootable freedos usb disk and copy this file to it or do this with...
  12. J

    Inconsistencies in Supermicro PSU cable list

    PWS-865-PQ with 4 6pin PCI-E this is rev 1.0, with 2 6pin PCI-E 2 6+2 8pin PCI-E - rev2.0.
  13. J

    CS-743TQ problem with configure backplane to SGPIO

    So this was sideband cable. Supermicro have pinout sideband connector like Adaptec, LSI has different pinout. LSI00411 (L5-00221-00) SB pin/SFF-8643 pin/Definition 2 - B1 - SB3 1 - D1 - SB5 4 - B2 - SB1 3 - C1 - SB4 6 - A1 - SB7 5 - D2 - SB6 8 - A2 - SB0 7 - C2 - SB2 Adaptec...
  14. J

    CS-743TQ problem with configure backplane to SGPIO

    Hello! I am have server Supermicro X10SRH-CF board with integrated LSI 3008 IT mode controller and case CS-743TQ backplane SAS-743TQ rev 3.00. To backplane connect 6 sata disk, backplane connect to HBA adapter with cable LSI00411 (L5-00221-00). Configure backplane for SGPIO mode (get config...