Search results

Basic command: “ip link set vf mac xx:xx:xx:xx:xx:xx” i.e. ip link set enp33s0f0v0 mac ea:a7:86:7d:85:e0

I set the mac addresses in the script even for the VF's highlighted down below, but it seems to be showing a difference mac address than I called out in the script or was expecting to show in proxmox. Red = PF Orange = VF As you can see the mac I called out in the script set correctly for the...

Thank you for the reply Heromode! (again). I don't see any errors, looks clean. I will mess around with the the script in segments like you suggested see if I can find the point of failure, great advice. I will also search for SR IOV and the connectx5 cards see if I can find a post with...

[Unit] Description=Enable SR-IOV and detach guest VFs from host Requires=network.target After=network.target Before=pve-firewall.service [Service] Type=oneshot RemainAfterExit=yes # Create NIC VFs # Starting SR-IOV ExecStart=/usr/bin/bash -c '/usr/bin/echo 10 >...

I swear I watched a video from Wendel @ levelone on this. But I can't find it.

I am a total script numb cake here, and I appreciate what you've learned, taught and done here, Thank you! Couple of questions please to help me understand what's happening. " ExecReload=/usr/bin/bash -c 'echo 0000:01:00.3 > /sys/bus/pci/devices/0000\\:01\\:02.1/driver/unbind' " It looks...

Yes that was a typo, I did mean to say both switches (ICX boxes).

I am reading up on spanning tree and rapid spanning tree, is there any primer you recommend? I feel like I am having some congestion on the network, specifically on the vlan carrying the cable modem as after about 6 hours the download speeds seems to be very slow, but if I reset both routers and...

None at all thank you for your help! I do need to plan out the rest of the network conversion phase, mostly around taking the network more vertical with the vlans, using the proxmox to host the vm's/services and using pfsense or something else to handle all the intervlan routing. I think I can...

I did try and set up the 6610 like I did the 7250, but lag 1 was not an option on the 6610. Maybe someone else has some input and knowledge they want to drop ;)

I attached the configs for both if there is a more convenient way to post the configs I am happy to do that too, let me know. Let me know how I can improve my config please and thank you for helping!

I am no expert lol, so take this with a grain of mega salt... A sanity check would be to make sure if using windows that the firewall isn't blocking your tftp server application. command would be: copy tftp flash IPHERE grz10100.bin bootrom (boot works too) Can you sh ver , sh firmware ver...

When I enter conf t on the 7250 and enter "interface ?" I get a list of ethernet, group-ve, lag, loopback, management, tunnel, ve. When I enter conf t on the 6610 the interface ? doesn't show "lag". Would assuming that adding dual-mode to the interface eth 1/3/1 after tagging the vlans is the...

Ok, I figured out where I was going wrong on the connection between the switches at least. I connected the switches using a dynamic lag (LACP) but I didn't know that I had to set a primary port and then "trunk deploy" command on the 6610 as it has older firmware. So now both switches see each...

I need some config advice. I have a 7250 flashed, licensed, racked up with UPS + cable modem, POE wifi AP + home office all wired up working fine. I have a 6610 flashed, licensed, racked up with UPS + NAS, Disk shelf, Hypervisor machines, misc servers, Starlink and POE wifi AP in the shop...

Hey Trophy, The ufo on a stick assigns the IP's. The wifi router which is powered by poe is just a wifi router. What is your router situation? Something like OpnSense can do multi-wan pretty easy. If you want to serve ip to your own router setup, you do that from the power brick. Just make...

My understanding is a power cycle (aka unplugging or unseating) of the power supplies will refresh the bmc placing them back into their auto mode. But I have no idea how to reset them while in play.

I will keep this photo album open for starlink related things: https://photos.app.goo.gl/5xo8bdYxS9qhwZEd8

Took forever to run the very thick outdoor rated Cat-X (cat6 quad shield? or ??) cable, it has 3/4 inch diameter (1.5 inches long) ferrite choke about 6 inches from the RJ45 plug... So you have to drill a 7/8" hole to pass it through and if you want it to move through a conduit, it will take...

Fedex made it's delivery. Now I need to fight the 5 inches of snow we got to install it on the J mast on the roof... I am certainly going to tie off and make sure my ladder is firmly planted in the ground. And ofc it's Friday the 13th lol.