Search results

Thanks mangodoc. Regardless, it's great info to me that your 7024 can do all those. I may try asking my seller if he can just swap my Delta Broadcom 7040 with a DNI 7024.

Wow! I'm assuming that the Dell OS gives it that functionality? I may try loading it if that's the case. One thing that's not clear to me is that your sysinfo shows what seems to be active connection, e.g. only 4 10Gb interfaces but the unit has 24. Mine shows all 24 ports as 10Gb. What does...

I was aware that he has an LB6M. What I didn't know was the RJ45 ports on that model are only 1Gb. That's interesting. I assumed all these models are the same since they have the same OS. I think the Dell 8024F is also like the Delta, 10Gb only on all ports. Man, if the LB6M could do auto-neg...

That is the default config from factory. If you want to save a config you can type 'write memory' or 'reload' if you want to revert a unit back to factory settings. If by gigabit ports you mean the 4X RJ45 ports, I've a feeling these are also 10Gb ports in RJ45 form factor and they're not...

Ok, found my answer. The unit has 24 SFP+ and 4 RJ45 combo ports. The RJ45 ports only support 10Gb links, it doesn't support 1Gb links. The eBay listing shows "4x RJ-45 1000Base-T (100Mb/1G)" however, this is false. Below is the show sysinfo output. Delta Broadcom 10GbE 24-Port SFP+ 4x1GbE L3...

I looked at the available settings but still couldn't figure it out. For those who own this model (Delta Broadcom ET-DT7040), are you able to use the RJ45 ports with no problems or initial configuration?

Kartoff and Mangodoc, thanks for the input. I tried all 10Gb ports on the switch and confirmed that they're passing traffic, that's good. It's just the RJ45 ports that is the issue. What's odd is if I use the same cable on the pic, and attach it to the OOB ServicePort at the back, set the...

The replacement Delta Broadcom ET-DT7040 arrived and I confirmed that the 10GB SFP ports work. I now want to use one of the 4 RJ45 ports and connect it to our gigabit switch to use as extension. I tried it but no traffic was passing, I'm using a CAT6 cable. Do I need to configure them to work...

They're the same switch, just different branding I think. With the default Delta software, you can transfer via tftp, scp or ftp. I will RMA the switch that I received since all methods I tried failed to even activate the ports. Hopefully the replacement will be problem free.

That's great news. I have the same exact switch but I haven't been able to use it yet since none of the ports seems to be active. I've already tried doing a factory reset. I may look into getting the Dell firmware installed. I just need to know if a straight firmware dump can be achieved without...

After a little more research I think what I really want is to set up one of the 1Gb ports to be a trunk that will be connected to another switch. How do I achieve this?

I connected the management port (labeled out-of-band) to our existing switch and set it to dhcp, it was able to get an IP from our dhcp server. I can ssh to it within the network. What I want to do now is make this an extension switch. However, if I connect a device to any port regardles 10GB or...

I was able to connect to the console using the Macbook and running show version gives the output below. How do I switch the Interface Status to Up? (FASTPATH Routing) #show network Interface Status............................... Down IP Address..................................... 0.0.0.0...

No worries! I'm hoping the console connection will help me identify the issue.

Turns out what we have is a Delta Broadcom 10Gbe switch which has the same OS and is similar to the Quanta. The four gigabit ports on the right (which I used) should be management ports. The console port is at the back. Delta Broadcom 10GbE 24-Port SFP+ 4x1GbE L3 Switch ET-DT7040 - Quanta LB6M...

I did try ports 21 -24 and connected it to the main switch which is connected to a Sonicwall FW which is also set up as a DHCP server.

Yes a switch (our only one). I also tried holding the reset button at the back of the unit with no luck. The same alternating blue/red light in front. I ordered a console cable and will connect directly to see what the current config is.

We recently purchased this unit. I connected it to our network using one of the gigabit port however the port is not active. There is an alternating blue and red light on the left side of the unit. It's not pulling an IP. What does the blinking light mean?