Search results

Hi Jason, And where can that version be downloaded? When I visit https://sonic.broadcom.com/ it says there's a problem with the website

Hi guys, I have a dozen of Mellanox MCX354A-FCBS Rev A3 cards (dual 40GbE), I was able to convert them into Ethernet using the firmware in the Nvidia/Mellanox website Firmware for ConnectX®-3 EN, I'm using firmware 2.42.5000 (MCX314A-BCBT with PSID MT_1090110023) and both ports are connected at...

Thank you Marc

Just wondering if someone has access to the official Arista download portal to confirm if this version is officially exists? Best regards

Here is the output of the unit: #sh vers Arista DCS-7050SX-64-R Hardware version: 12.23 Serial number: SSJ163XXXXX Hardware MAC address: 444c.xxxx.xxxx System MAC address: 444c.xxxx.xxxx Software image version: 4.28.13M Architecture: i686 Internal build version: 4.28.13M-40288711.42813M...

Hi guys, I hope you're doing well. I have some 7050QX-32S devices that are running version 4.28.13M, which seems to be the latest release in the 4.28 train. However, I haven't been able to find official reference from Arista about that version, so I'm wondering if that an official release or an...

And here is the output of the "show hardware capacity" command #show hardware capacity Forwarding Resources Usage Table Feature Chip Used Used Free Committed Best Case High...

Hi guys, I hope you're doing well. I'm new to the 7280r family of Arista devices. I just got a DCS-7280QR-36, and I'm wondering if it can really support full DFZ in both IPv4 and IPv6? I run the FlexRoutes commands "#ip hardware fib optimize prefixes profile internet" and "#ipv6 hardware fib...

Hi DrMuffinMD, I hope you're doing good. I saw your post on Juniper firmware. I just got my first MX204 with firmware 18.2R2.6 and found a file for 23.4R1, but it appears I need to upgrade through intermediate versions. Do you have any older files you could share for a step-by-step upgrade...

Hi, Does anyone have the version junos-install-mx-x86-64-23.4R12-S3 for MX204? Unfortunately I don't have access to the Juniper download site. My MX204 is currently in version 18.2R2.6, can I go directly to the latest firmware version? Thanks,

Thanks

Hi, Does anyone has experience with this model? Thanks

Hi guys, I have an Arista DCS-7280QRA-C36S (this is my first time with this model), and I'm trying to set the 12 ports that support 100G mode in that speed, however, I don't know what are the ports that can be configured in 100G mode. I thought that are the odd ports 7-29, but when I configure...

Hi guys, I hope you're doing well. I was reading some reddit posts saying that Arista CVP server can be installed for free on premise, is that true? Do you know where could I get the installation image or url to install in on a CentOS server? Thanks, Best regards PS: I don't have access to...

The problem is what version to use in the dx010. The best version I have used it the one from Broadcom for Sonic Enterprise 3.1.2 https://sonic.broadcom.com/

Hi guys, I hope you're doing well, I have some EOL Arista switches and I currently monitor them using LibreNMS or Zabbix, however, after watching some CloudVision videos I am in love with the streaming telemetry, I'm wondering if there's an open source alternative to CloudVision for that kind of...

Hi guys, I was wondering if anyone has the image for firmware version 4.26.13M for Arista? Best regards,

Is there anyone else experiencing these issues with that hardware model? Best regards

Hi guys, I have been using Arista switches for long time and love them, a few years ago we purchased several Arista DCS-7170-64C and DCS-7060CX-32S, I prefer the first one since it has 64 100G ports instead of the 32 ports of the 7060CX-32S, and they don't use a lot of power. However, I have...

Hi guys, I hope you're doing well. I have some switches running the Enterprise Sonic by Broadcom release 3.1.2 due to better stability and working features compared with compiled version of Sonic.202305. However, I haven't seen a new version since long time ago. Do anyone know if the Broadcom...