Search results

@JimsGarage glad I ran into your YT channel the other day, got the Authentik going. Nice to see you here :cool: Speaking of MS-01, did you by any chance tried to do PCIe passthrough on USB4 port controller? For some reason and other have reported this too, it does not work. I'm hoping to only...

While I have not tried to make the AMT work on 1G switch, only 2.5G. I'm curious is your thunderbolt/usb-c dock 2.5G speed or 1G?

Damn, love it. Impressive rig. I hope you're not sitting anywhere close to this monster of a setup :cool: I do wonder how much your electric bill runs each month ;)

Sounds like IOMMU index change issue due to addition of new PCIe device to the system. Most likely Ethernet index number moved one step up or down. Do "ip addr" and note down the Ethernet interface name and manually edit that into /etc/network/interface.

Guys, have had good luck getting Intel AMT and MeshCentral going, sable to far. Anybody know if it possible to put Intel I-226LM NIC is low power mode, when not actively used, example 10Mbps to save power? Either in BIOS or force switch to negotiate only to 10Mbps?

I'll begin by asking what all fun things you do with your three cluster rig? :cool:

No need to be sorry, we are all here to learn and share.

Why would it not? Take a closer look? I've been using 22110 on this same card.

You need something like this, while it has two slots. 22110 drive in first slot will be recognized. https://www.aliexpress.com/item/1005005325573519.html

Samsung PM983 3.84TB M.2 22110 PCIe Gen3 X4 NVMe SSD MZ1LB3T8HMLA https://www.ebay.com/itm/284964024159 There are PCI M.2 cards out there that can do 22110 but thing to keep in mind that even through slot is x8, it can't do bifurcation, so you'll have to get card with PCI switch, which means...

The other day I used a spare power adapter rated at about 120W because original power supply was sitting inside cabinet and not long enough to reach. Boy, right after reboot and going in OS boot, machine went total blank. 120W watt that most Intel NUC use, can't even power this beast. So...

Folks, anybody kind enough to post pictures of MS-01 fan (CPU and NVME) that also clearly show fan connector? Sorry my machine is in mission mode and hate to take it down just yet. Got in touch with Aliexpress seller based on other poster recommendation, thanks! They do have these fan but want...

Ouch, that sucks. What was your use case like? Heavy load or mostly idling? Thermals are not the best on this machine, makes me wonder if CPU cooked itself. Did you try removing the battery to clear up the CMOS?

Yes, it works, been using it for a while now. Both with and without SR-IOV. Is IOMMU separated out for both ports if you run "lspci -v"?

As @ms264556 mentioned, a slim, about 2mm thick heatsink is included with the MS-01.

Few clever folks on here added a shim to extend the height to accommodate 15mm tall U.2, if custom modding is your thing.

If by first M.2 slot up mean one that's designated to take U.2 drive, yes, 7-8mm will be height clearance for any heatsink. Slot in the middle can take 1mm slim heatsink. And one of the far right (right below the fan) have zero clearance, so putting any heatsink on that one is no possible.

Thanks for the pointer. Having a spare won't hurt I figured and these laptop size fans are not really know to have good quality or longevity unlike Noctua, easy to find and replace.

Folks, is this for 3.5mm audio jack on MS-01 front panel? Anybody have had luck getting audio from this jack from a VM? 00:1f.3 Audio device: Intel Corporation Raptor Lake-P/U/H cAVS (rev 01) DeviceName: Onboard - Sound Subsystem: Device b015:1f4c Flags: bus master, fast...

Mine shipped back in March came with 17, updated to 22 yesterday. While the update process went smoothly, upon reboot screen was blank and that had me immediately regret the decision to update. Anyway, after clearing up the CMOS, screen finally came back. Phew... Did not dig into all the BIOS...