Search results

Update on this, the plastic oozing out must be glue when they built the switch. I found another post of this forum talking the switch flashing PWR light is a boot failure, but you can access the switch on 192.168.1.1 so I plugged the switch in, hit that address and a cut down UI appeared. I...

Mine just went into rave mode. I popped the lid and found plastic oozed out the chip behind the 10gbe NIC.

Yep agree, however I've had a T1700X-16TS since 2018 and it has been bullet proof. I had a T1700G-28TQ from 2018 to mid 2024 when I upgraded to the 2.5GbE version, it was bullet proof except for an early firmware that had a memory leak. The SG3428X-M2 I replaced it with this year has been good...

Seller was going to send me an updated firmware and asked what version I had but after I said 1.9.1 they went radio silence. I've since messaged them about the failure and again radio silence. I'd probably have to pay to post it back and it is probably going to cost me just as much in postage...

Layer 3 (L3) is why it is pricey

I know the Intel 225 and 226 are meant to be trouble but under BSD the've worked flawlessly in pfSense and in TrueNAS Core. I got a TP-Link Realtek based 2.5Gb NIC and it has been nothing but trouble in my wife's PC. Works for the most part but randomly stops passing traffic. I put a cheap...

I had two Qotom 4th gen Intel AliExpress specials run pfSense in two houses for many years. I think one was purchased in 2015 and the other 2019 and both still work today. I upgraded the one from 2015 to a N100 based system with 6x 2.5GbE NICs from CWWK on AliExpress. I figured out that they are...

Well I left the switch running on my desk, and eventually two LAN ports stopped working, the switch also started buzzing near where the power adapter goes in. Then the power light went solid green instead of flashing. I tried factory resetting the switch but the reset button no longer appears to...

Yep 1.9.1 from earlier this year

Yep same, mine worked fine since April 2024 to October 2024. I'm wondering if these things don't like heat as moving into summer we have gone from ambient 15c to 25c

I'm running 3x Unifi nano APs and they draw 5w each so the original 52v 1.25a power supply should be sufficient. I did intend to upgrade my APs at some point so I got Hasivo to send me their 52v 2.5a power supply which is double what this switch came with. I have disconnected my access points...

Thanks @bugacha. Mine started doing it within a few minutes this morning too. No longer lasting a day I set explicit port speeds but that didn't change anything.

I purchased a Hasivo S600WP-4GT-2SX-S PoE switch from AliExpress in April and over the last week it has started crashing once per say where the switch is still on, but no longer passes traffic, and you can no longer reach the WebUI over HTTP, and it no longer responds to a ping. This causes the...

Hence why I only used one. DAC cables in the other SFP+ ports. With the T1700x-16ts I don't need to use transceivers in the TL-SG3428X-M2

I have just put in a SG3428x-M2 which is 24 2.5Gb RJ45 and 4 10Gb SFP+ ports. I picked it up for AU$600ish and it is working well. No noise, cool running. Probably similar to the SG3210x, just with more ports I guess. TP-Link transceivers I usually get off AliExpress. I also found the Horaco...

I was ab I was able to change the power limit from the default 65 to 130, but I changed it back again. I have yet to find a quality 52v 2.5a power supply. The only ones I've found have been from AliExpress. Probably of similar quality to that which would be supplied by Hasivo. Hasivo have not...

Good to know. I reached out to Hasivo to see if I could get a 120w power supply for my switch. But they tried to sell me a whole new switch. I'm considering upgrading my Nano HD access points some time in the not too distant future and looking at the U7 Pro or equivalent at the time they have...

I couldn't wait so I got the switch set up. I have the two 10Gb SFP+ ports in LACP back to my TP-Link SG3428X-M2 core switch. I set the LACP config on the TP-Link side to Active LACP and Hash Algorithm to SRC MAC + DST MAC, and it seems to work with that. My primary LAN and guest LAN seem to be...

My S600WP-4GT-2SX-SE has just arrived. I will get to look at it hopefully some time this week

I got a similar switch locally in Australia. The SG3428X-M2 has 24 2.5GbE ports instead of 16, but comes with an English UI. It works well and I have no complaints. https://www.tp-link.com/au/business-networking/omada-switch-l3-l2-managed/sg3428x-m2/