Hi everyone. Looking at the ICX7150-48ZP, what does the E2X10G vs the E8X10G designation mean? They both seem to have eight 10 gig ports. Is the former licensed for just 2 active?
Doesn't look like SFF-8087. I included a couple more photos with an SFF-8087 connector.
It does look like a SlimSAS connector but the 4i variant. I'm going to try a cable from Amazon just in case I need to return it.
Side question - Anyone know of a SATADOM device that could plug into...
I have one with 4 nodes running at a colo. Did you buy them all together or as separate pieces? I found out the hard way that the chassis are not all the same and the nodes will only power up on the right chassis.
Bought cheap Oculink via Amazon. Had errors, hangs and disappearing drives on POST. Got Supermicro cables and they are rock solid after over of year of operation.
Fortunately, it's no longer available: https://www.amazon.com/gp/product/B09C1WKLF8/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
I have a Corsair AX1200 that I purchased in January 2011. It's still going strong in my Corsair Obsidian 800D case (purchased the same time). I believe the motherboard has been upgraded 4 times, maybe 5. The first video card in that case/power supply was a 8800 GTX times 3 for triple SLI and...
Thanks for the help. Unfortunately, it's still not working for me:
IBM-SSG IBM-SSGSSNU7P6 E185 peripheral_type: disk [0x0]
PROTECT=0
Unit serial number: HSR031B10000822150Z3
LU name: 5000c500a1844b44
mode sense(6) cdb: [1a 00 01 00 fc 00]
Mode Sense (block...
Hello everyone. I picked up one of these drives off Ebay and I can't seem to get it recognized by my SAS controller (LSI 3008 onboard controller on a Supermicro MB). During POST (while the controller scans the bus), the drive doesn't show up. Other SAS and SATA drives show up fine, including...
Hi everyone. I'm trying to install a couple of these SATA SSDs into the built in M.2 riser on a Proliant X170R node for an ESXi datastore. It works and is recognized, but after a few minutes of operation, iLO5 reports that sensor 60 (AHCI HD) reports a high temp situation and the server shuts...
Is one access point enough to cover your home? Is it enough to handle all your wireless clients? You might benefit in adding an additional access point and theoretically splitting all your wireless clients between two APs and therefore, two separate gigabit connections.
Why not just mount the .ISO as virtual media thru the iLO and boot off of that? During post, hit F11 for the boot menu and select iLO virtual media.
If you go into Intelligent Provisioning you can also upgrade the firmware as long as the server has an internet connection. Truth be told...
Hi everyone. I'm looking for four vSAN cache drives for my cluster but I'm having trouble finding something affordable. Optane p4801x is too expensive. I have 4 nodes with 6 SATA SSDs (Samsung 960 Gig) each. I'm looking to run ESXi 7.0u2 or higher. Its doesn't have to certified as this is...
Here's the link: *New* HP 874491-001 Apollo R2600 Gen10 Barebones Chassis SFF W/ 4x Fans
Anyone familiar with these Apollo chassis? I can't find any details on 874491-001, but it looks like 867158-B21 - HPE Apollo r2600 24SFF-Prem Gen10 CTO Chassis. Next closest seller is in the $600 range...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.