Search results

Yes, this is probably some kind of custom-built budget version, but the strangest thing is they skimped on the connectors. All the components are there, even the LEDs indicating M2 drive activity. Probably if you solder the connectors onto this board, everything will work. The seller actually...

Yes, you're right. I just took the riser apart and there are four connectors, two for the top slot and two for the bottom. The problem is, there's nowhere to connect the remaining two on the Z12 board. None of the slots are soldered.

Can you attach the manual? I couldn't find one for the R162-Z12, only for the R162-Z10/Z11.

Hi, I need help with this server. I can't get the PСI-E slot bifurcation to work correctly. On a two-slot riser (connected to the board via a ribbon cable), only the top slot always works. I've tried setting PСI-E #2 to auto, x8+x8, x4+x4+x4+x4, but the result is always the same. Maybe someone...

I ran the program again. One of the addresses reported being flashed, and the second completed flashing again. After that, everything worked! Thank you!

Hello! I tried flashing Dell P640. Below is the console output. I installed 8259СL processors. The server won't start (it hums, but the screen is black). Processor 1 is completely cold, processor 2 is warm. Any ideas what this could be...

Hi all. I need help. FlexFabric 20/40 F8 module is connected to Cisco 9396PX with 40GbE QSFP-CR4 DAC cabels VC Q1.1 port status is "Not Linked". From Cisco side also No Link I have two such modules, two cables, both are connected to Cisco and both have this status. I don't know what to do with...

Hi all. I installed such an SSD in the HPE server, downloaded the drivers from the Lenovo website, after installation the driver asked to update the firmware and now nothing works... The update was successful, but now when I try to install the driver the device disappears from the device...

Hello. I am bought bl460c gen10 + m.2 kit (riser + interposer) Some of the entries alarmed me in quick specs doc So i have two questions,maybe i misunderstand something - If i put m.2 ssd in server and sata SSD will be it work or not? - If i put m.2 ssd for example 4Tb and 1Tbwill be it...

Hello! Docs for HPE Virtual Connect FlexFabric-20/40 F8 Module says: "Virtual Connect FlexFabric-20/40 F8 modules are supported on c7000 enclosures with the following SKUs: 5XXXXX-B21, 6XXXXX-B21, and 7XXXXX-B21" But what will happens if i put this modules in 4XXXXX-B21 chassis? Maybe somebody...

It's great news! So as i can understand its need only firmware upgrade?

Hello, i make new thread, but after find this. Help me please) Its possible upgrade v2 CPU to v3 CPU in DDR3 books?

Maybe someone can help explaine me next thing: If i have X3950 x6 with E7-8800 v2 CPU and DDR3 RAM compute books, can i upgrade E7-8800v2 CPUs to E7-8800v3 CPUs without upgrading compute books? In docs they say next Supported upgrades are: E7 v2 processors to E7 v4 processors (new DDR4 DIMMs...

So what about P-8124? Will it work in DL360 Gen10?

Look at Quanta LB4M (48x 10/100/100 + 2x 10G SFP+) or Quanta LB6M (full 10G) Nice switches for those price

Hello. I can’t get the mezzanine card to work in the Dell M520 serve. Mezzanine card p/n 073TM8. This is LPm16002B-D 16gb fiberchanel card. When i try to start server with this card i taking message "Unsupported mezzanine card istalled! System halted" In dell m610 this card works fine. Is there...

I watched russian webinar (HPE russia channel), speaker says that superdome 2 and superdome X chassis is same, but in superdome X they reworked XFM modules. So i think it will be work

I know, its a vary strange question, but..) It is possible to use Superdome 2 chassis (maybe with crossbar modules upgrade) with BL920s G8 or G9 blades? It seems like they physically compatible at first look.

8xxx Series is too expensive for me and i think its have same problems - licensing

Yes, disk shelves not a problem, i have 3x42U racks in my lab) But licensing is a real trouble( Maybe you tell me about newer models from mid-range segment? This is a very interest for me.