Search results

not work for 16G cause each boot time it reset bit and rewrite ttl,ttlV2 (8.2.3d) better to set eeos license.. but probably mostly jumped to 32G and there is no members of forum with eeos and fabric os Upgrade switches. need to change date and disable NTP under "single" boot (or /init/sh)...

Password for console and telnet is the same. and available in NVSRAM file encrypted. ".Recovery Password 0x00, 0x08" You won`t find information about changing submodel, cause it`s for special tech users, to perform an storage to accept any unbranded sas hdd. Onсe again - firmware generally is...

there is no cross-flash: you need to switch Submodel ID. (only after this new firmware version should be installed, in case of IBM only, but not Netapp for example) but there is also OS protection by part number (if it uses): you`ll get after time an error "controller mismatch". so this is...

you`re wrong: there is NO DIFFERENCE in Onyx: can take if from HP or Mellanox/Nvidia site. As it was for SX6 series. Cumulus demands license! and it`s more complicated to adjust switch and need to get license (but less expensive, B2B is excluded for compare)

..license that available. so there is no way or needs for converting, cause this is the same hardware (with naming in eeprom probably) AND Onyx firmware this is not the same that was with SX6036/6018/6012 under EMC firmware and Mellanox firmware.

If all ports (except mentioned) are lighting (green led if I right), then it working. If blinking or come down (you see it in console output "error message "administratively down"") then isn`t working right now. If doesn`t react at all, then maybe hardware issue in port (physical damage). Please...

at least switch doesn`t have additional licenses. default config disables ports (config, interface TenGigabyte.. 1/0/1-48, switchport) (config, dpod 1/0/1 reserve) VDX6740 SFP+ model have basic 24 active ports 10G, and no one 40G. show dpod. but it`s solvable. (pm only)

you can! logical chassis do nothing for you. "Network OS 7.1 supports logical chassis cluster (LC) mode only" in own cases have a lot of customers with only one switch per rack, of course with last firmware release.

reset factory can`t help you if firmware upgrade process isn`t ended. only netinstall will format CF-card and copy new filesystem of provided version. "show firmwaredownloadstatus" confirm that previous update finished? "show version" in case of Logical chassis will show 2 partitions. in case...

There is no problem to use Logic Chassis as "normal" switch: you don`t pay for it by performance. especially when this is the Only one variant (since 7 release if I remember). of course you can try to use netinstall flash to make clean install any version of NOS (don`t forget to save license keys)

there was no demands in request - I supposed you connect devices within 5m. this is DAC, not cable. MPO(MPI) cable + transceiver costs a lot. if you really need distance more them 50m.

mc2207128-003 (3m cause 1m,2m is rare) $10-30 on ebay

for 56Gb speed you need: -original QSFP+ Mellanox equipment (cards, switche, cables. only Mellanox offered FDR14 encoding) -change speed on port from 40Gb to 56Gb (for safety, switch won`t do it itself)

I had installed about hundred of these switches without problem. Maybe you too hurry: switch has some notes: 1.it`s slow (especially in compare with sn2700). to up IB connection need 3 minutes, for ethernet less (if I remember). 2.there is no light if connection is not up. 3.if you use...

then our questions is not major. looking for manual to setup routing between networks with "route" command in windows. or make a Bridge in "network settings" with your "network-internet" card and Mellanox-card (or Solidfire: depends which one in network) of course we not mentioned if "shared...

Model is written on card. IF ONLY this is VPI model (MCX354) in "System Devices" there is "......Mellanox...mt4099......" when you can change settings: auto (default IB, Ethernet, IB). but maybe this is only ethenet MCX314 model. is 7122f SFP+ model? then how did you connect it to QSFP port...

Yes, you need install a license to get variant not only "ib-single" mode, but also "vpi-single-switch" or "ethernet" in System Profile view. VPI is when you select IB or Eth type for Each port.

you can make printscrn or copy text output of "showlicense" if you want. this will need IF only you want to replace CF-card (if it dead). GUI BNA 12.2 trial can be downloaded from ICX Ruckus site. Won`t help with cookbook. maybe exists good youtube plays, or even Brocade classes records.

no problem at all to find it. ftp://188.64.160.99/pub/fw/ and COM1 console port (or ssh if you know ip of management). forget about ezswitch

anywhere, even on public FTP "swbd76"