Search results

I was not able to find the software which is needed to enable the backup and restore functions of the NV1616. Unless one has a source for the required software, the NV1616 will only function as a volatile block device.

@fohdeesha we will miss you even for a few days. Take care and hope you will be fully recovered quickly.

By the way, you could also use a free version of Ekahau HeatMapper to optimize your AP placements Free Wi-Fi heatmap coverage mapping software for homes and small offices - HeatMapper | Ekahau

I don't think their free offer is the software itself. Instead, they will feed your floor plan to their software and mail you back the result.

I am pretty sure you are going to have a lot of fun with your new toys. :-)

"A site map in a format supported by Ruckus ZonePlanner (supported formats are: bmp, dib, dwg, dxf, emf, gif, vsd, jpg, or wmf)" https://webresources.ruckuswireless.com/pdf/datasheets/ds-zoneplanner.pdf

As far as I know, just a firmware update. I am still waiting for my 4x R500 to show up.

Ruckus also offer a free site survey service: FREE Wireless-LAN Site Survey | RuckusSecurity.com Here is a youtube video on their site survey application:

I hope following will give you more info on the smart antenna system used in Ruckus AP products. BeamFlex Smart Antenna System http://a030f85c1e25003d7609-b98377aee968aad08453374eb1df3398.r40.cf2.rackcdn.com/feature-sheets/fs-beamflex.pdf ZoneFlex R500 Data Sheet...

Since I am a newbie to Ruckus AP, I will let others who have much more experience answer your questions.

You could get a Ruckus R600 from ebay for much less than $600 such as this: Ruckus R600 Dual-band Wireless Access Point | eBay Here is the R600 data sheet: http://a030f85c1e25003d7609-b98377aee968aad08453374eb1df3398.r40.cf2.rackcdn.com/datasheets/ds-r600-unleashed.pdf I just recently...

The vendor accepted my offer of $201 for three units.

Here are the results I obtained by running a low latency test and a high throughput test on my NV1616 production model card: ------------------------------------------------------------------------------------------------------------------------------------ Test 1 - Low Latency Test fio...

I suspect the NV1600 is using this controller. PM8607 NVMe2016 | Microsemi

FYI: Here is the review article on the 4GB version of this product. PMC NV1604 Flashtec NVRAM Drive Review | StorageReview.com - Storage Reviews

Thanks @javlk50k and @Rank for the information. I just brought two of the prototypes from the same vendor. Just by looking at the pictures on eBay, I suspect those two should also have 16GB of ram.

rpm = (max_rpm - min_rpm) * duty_cycle + min_rpm If we assume the following: max_rpm = 14700 min_rpm = 2650 duty_cycle = 0.5 The rpm should be: rpm = (14700 - 2650) * 0.5 + 2650 = 8675 rpm You could also try to set the duty cycle to 0% by just connecting the fan PWM pin to ground: rpm =...

I don't know whether this will work but you could try to connect your pulse generator output to the PWM input of you fan. Assuming your pulse generator is generating a square wave with 50% duty cycle. your fan should spin at the speed close to the midpoint between the maximum speed and the...

There are 27 occurrences of the string "460EX" in this document: https://www.mellanox.com/related-docs/prod_management_software/MLNX-OS_ETH_v3_6_3508_UM.pdf

SX6000 series is based on the SwitchX ASIC. The SwitchX Development Kit has an integrated PPC CPU. http://www.mellanox.com/page/products_dyn?product_family=126&mtag=switchx_dvk