Search results

Hi! Firstly, you can use it with a standard u.2 cable, when your board has an u.2 connector. This unit has only two pci-e 3.0 channel, so it's not an x4 drive just x2. Performance-wise is good in seqeuential read and write but in qd32 4k is very poor near 1mb/s. I din't now it's a firmware...

I've made it!!! After linux with nvme format, I can access the drive now from windows 10.

Yes! Can you give me some advice? Under linux I can see it, but gparted gives me I/O error if I want format or something else.... Maybe NVME format could help?

Hi! I've got a little problem using Huawei HSSD-D5223 Nvme drive. I can see it under HDsentinel and under win10 diskmanagment but can not format, and can not make a partition on the drive. Could it be the problem that the drive has 520 byte sector? Or something else?

Under linux the sg3 utils neither detect the drive, because it's a special pci-e drive and not nvme.

With HDD sentinel you can check it easily. Or you can download micron's own utility (realssd manager) to these drives and this software you can make everything that's why I prefer micron's utility. I've got 3x 175 gb p320h and it's a fantastic drive, high speed, lowest latency what I ever saw...

Hi! I want to buy this drive but not sure that's works with a standrad SAS controller that not TCG compatible. It's a new drive, never used, can I use it without TCG encrypton with a standard SAS controller or it's just works only in TCG mode?

Hi! I have an ADATA SR1020 2TB SSD and try to use it in my X99 setup but it doesn't work... I didn't see it in the nvme setup and under win 10... I use with a SFF8639 cable with this cable my Micron P320h works flawlessly... Any idea?

Hi! I have an ADATA SR1020 2TB SSD and try to use it in my X99 setup but it doesn't work... I didn't see it in the nvme setup and under win 10... I use with a SFF8639 cable with this cable my Micron P320h works flawlessly... Any idea?

How much written data were on these drives in smart info?

All of these drives came with 520 blocks... Made by HP, firmware is HP too...

How much written data were on these drives?

Same issues.... Had a WD Raptor 150Gb in 2005. In 2007 it failed and the joke is that it was waterccoled. The drive was never hotter than 41-42 celsius... And it was 200 us dollar...

This drive uses only 12V so I didn!t connect the others only the ground... :)

THANK YOU MAN!!!!!! YOU MADE MY DAY!!!! I changed the +12Volt pin to the corect position and now the drive works!!!!In the UEFI I didn't see it (I think because it's not a nvme drive) but under win 10 it works perfectly :) I buy this drive for 81 US Dollar from ebay and it has 6 work days and...

oops....You are right... But then I already made a big overvoltage to the drive? Maybe I killed it? How can you change to 3.3 volt? The other voltages is ok but 3.3 volt in a 4 pin conncetor I can not make...

With those cables the drive didn't even get power? Cause my drive doesn't get warmer after 30 minutes...

No other nvme ssd here... Make photo from what? SSD? Or cable?

It's support nvme as boot disk.... Asus rampage 5 extreme, x99 board... Natively support nvme. But if it's not support the drive, it shuould heat up anyway if I plug the power connector or am I wrong?

Ok, but it could be that this drive is bad... I have no other idea... Not heating up, not working, in the UEFI I didn't see it, I enable the asus hyper kit using in the uefi, m2 connector is enable... I can not make anything else....