smartctl 6.5 2016-05-07 r4318 [x86_64-linux-4.14.13-unRAID] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke,
www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Samsung based SSDs
Device Model: Samsung SSD 850 EVO 500GB
Serial Number: Serialz
LU WWN Device Id: 5 002538 d426ccda2
Firmware Version: EMT03B6Q
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Tue Jan 30 10:55:54 2018 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x53) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 265) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0
9 Power_On_Hours -O--CK 099 099 000 - 15
12 Power_Cycle_Count -O--CK 099 099 000 - 6
177 Wear_Leveling_Count PO--C- 099 099 000 - 2
179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0
181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0
182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0
183 Runtime_Bad_Block PO--C- 100 100 010 - 0
187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0
190 Airflow_Temperature_Cel -O--CK 072 054 000 - 28
195 ECC_Error_Rate -O-RC- 200 200 000 - 0
199 CRC_Error_Count -OSRCK 100 100 000 - 0
235 POR_Recovery_Count -O--C- 099 099 000 - 3
241 Total_LBAs_Written -O--CK 099 099 000 - 2208049683
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 1 Comprehensive SMART error log
0x03 GPL R/O 1 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x13 GPL R/O 1 SATA NCQ Send and Receive log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa1 SL VS 16 Device vendor specific log
0xa5 SL VS 16 Device vendor specific log
0xce SL VS 16 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
255 0 65535 Read_scanning was never started
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 256 (0x0100)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 28 Celsius
Power Cycle Min/Max Temperature: 23/45 Celsius
Lifetime Min/Max Temperature: 40/45 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 10 minutes
Min/Max recommended Temperature: 0/70 Celsius
Min/Max Temperature Limit: 0/70 Celsius
Temperature History Size (Index): 128 (103)
Index Estimated Time Temperature Celsius
104 2018-01-29 13:40 ? -
... ..( 22 skipped). .. -
127 2018-01-29 17:30 ? -
0 2018-01-29 17:40 40 *********************
1 2018-01-29 17:50 ? -
... ..( 9 skipped). .. -
11 2018-01-29 19:30 ? -
12 2018-01-29 19:40 29 **********
13 2018-01-29 19:50 ? -
14 2018-01-29 20:00 ? -
15 2018-01-29 20:10 28 *********
16 2018-01-29 20:20 35 ****************
17 2018-01-29 20:30 35 ****************
18 2018-01-29 20:40 37 ******************
19 2018-01-29 20:50 24 *****
20 2018-01-29 21:00 23 ****
21 2018-01-29 21:10 24 *****
22 2018-01-29 21:20 23 ****
23 2018-01-29 21:30 24 *****
24 2018-01-29 21:40 24 *****
25 2018-01-29 21:50 23 ****
26 2018-01-29 22:00 23 ****
27 2018-01-29 22:10 23 ****
28 2018-01-29 22:20 ? -
29 2018-01-29 22:30 43 ************************
30 2018-01-29 22:40 42 ***********************
31 2018-01-29 22:50 45 **************************
32 2018-01-29 23:00 40 *********************
33 2018-01-29 23:10 40 *********************
34 2018-01-29 23:20 40 *********************
35 2018-01-29 23:30 28 *********
... ..( 15 skipped). .. *********
51 2018-01-30 02:10 28 *********
52 2018-01-30 02:20 27 ********
... ..( 23 skipped). .. ********
76 2018-01-30 06:20 27 ********
77 2018-01-30 06:30 26 *******
78 2018-01-30 06:40 27 ********
79 2018-01-30 06:50 27 ********
80 2018-01-30 07:00 27 ********
81 2018-01-30 07:10 26 *******
82 2018-01-30 07:20 26 *******
83 2018-01-30 07:30 27 ********
84 2018-01-30 07:40 26 *******
85 2018-01-30 07:50 26 *******
86 2018-01-30 08:00 26 *******
87 2018-01-30 08:10 27 ********
88 2018-01-30 08:20 27 ********
89 2018-01-30 08:30 28 *********
90 2018-01-30 08:40 27 ********
91 2018-01-30 08:50 28 *********
92 2018-01-30 09:00 30 ***********
93 2018-01-30 09:10 31 ************
94 2018-01-30 09:20 34 ***************
95 2018-01-30 09:30 36 *****************
96 2018-01-30 09:40 28 *********
97 2018-01-30 09:50 29 **********
98 2018-01-30 10:00 28 *********
99 2018-01-30 10:10 29 **********
100 2018-01-30 10:20 27 ********
101 2018-01-30 10:30 27 ********
102 2018-01-30 10:40 28 *********
103 2018-01-30 10:50 28 *********
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 0 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC