=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 57) A fatal error or unknown test error
occurred while the device was executing
its self-test routine and the device
was unable to complete the self-test
routine.
Total time to complete Offline
data collection: ( 60) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 6) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 199 051 Pre-fail Always - 106
3 Spin_Up_Time 0x0027 203 197 021 Pre-fail Always - 8833
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 208
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 063 063 000 Old_age Always - 27028
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 208
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 203
193 Load_Cycle_Count 0x0032 197 197 000 Old_age Always - 10321
194 Temperature_Celsius 0x0022 115 095 000 Old_age Always - 37
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 170 000 Old_age Always - 213471
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
SMART Error Log Version: 1
ATA Error Count: 9 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 9 occurred at disk power-on lifetime: 26364 hours (1098 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 00 00 00 00 40
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
e3 00 00 00 00 00 40 00 00:08:34.049 IDLE
ef 42 00 00 00 00 40 00 00:07:34.104 SET FEATURES [Enable AAM] [OBS-ACS-2]
ef 85 00 00 00 00 40 00 00:07:34.080 SET FEATURES [Disable APM]
Error 8 occurred at disk power-on lifetime: 26364 hours (1098 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 00 00 00 00 40 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 42 00 00 00 00 40 00 00:07:34.104 SET FEATURES [Enable AAM] [OBS-ACS-2]
ef 85 00 00 00 00 40 00 00:07:34.080 SET FEATURES [Disable APM]
Error 7 occurred at disk power-on lifetime: 26364 hours (1098 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 00 00 00 00 40 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 85 00 00 00 00 40 00 00:07:34.080 SET FEATURES [Disable APM]
Error 6 occurred at disk power-on lifetime: 26364 hours (1098 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 00 00 00 00 40
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
e3 00 00 00 00 00 40 00 3d+04:05:45.687 IDLE
ef 42 00 00 00 00 40 00 3d+04:04:45.711 SET FEATURES [Enable AAM] [OBS-ACS-2]
ef 85 00 00 00 00 40 00 3d+04:04:45.686 SET FEATURES [Disable APM]
Error 5 occurred at disk power-on lifetime: 26364 hours (1098 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 00 00 00 00 40 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 42 00 00 00 00 40 00 3d+04:04:45.711 SET FEATURES [Enable AAM] [OBS-ACS-2]
ef 85 00 00 00 00 40 00 3d+04:04:45.686 SET FEATURES [Disable APM]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Fatal or unknown error 90% 27028 -
# 2 Conveyance offline Fatal or unknown error 90% 26882 -
# 3 Conveyance offline Fatal or unknown error 90% 26857 -
# 4 Extended offline Fatal or unknown error 90% 26840 -
# 5 Extended offline Aborted by host 90% 26840 -
# 6 Extended offline Fatal or unknown error 90% 26840 -
# 7 Conveyance offline Fatal or unknown error 90% 26840 -
# 8 Conveyance offline Fatal or unknown error 90% 26837 -
# 9 Conveyance offline Fatal or unknown error 90% 26597 -
#10 Conveyance offline Fatal or unknown error 90% 26573 -
#11 Conveyance offline Fatal or unknown error 90% 26546 -
#12 Extended offline Interrupted (host reset) 40% 7289 -
#13 Conveyance offline Completed without error 00% 7283 -
#14 Short offline Completed without error 00% 7283 -
#15 Extended offline Completed without error 00% 6950 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.